• Journal of the Korean Electrochemical Society
• /
• v.2 no.3
• /
• pp.117-122
• /
• 1999

This study investigated the corrosion rate of aluminum in alkaline solution. It was performed to observe the effects of alloy element, alkalinity (KOH concentration), solution temperature, and inhibitor and its concentration in the solution. Among species of aluminum, AA-1050 showed the lowest corrosion rate due to its high purity $(>199\%)$, whereas alloys containing Mg anuor Mn were highly corroded, relatively. The corrosion rate could be reduced over than $50\%$ by saturating the solution with ZnO, while ZnAc did not work as an inhibitor. The inhibition effect of ZnO increased with increasing the alkalinity and solution temperature. It was found that the corrosion rate linearly increased with the concentration of KOH in first order and exponentially decreased with the inverse of the solution temperature. An analysis of the corroded material covered the surface of aluminum was made by SEM and EDS. According to the analytical results by using XRD, it was confirmed that $Al(OH)_3$ was produced from the corrosion of aluminum in KOH solution.

• Korean Journal of Materials Research
• /
• v.29 no.12
• /
• pp.798-803
• /
• 2019

The self-discharge behavior of zinc-air batteries is a critical issue induced by corrosion and hydrogen evolution reaction (HER) of zinc anode. The corrosion reaction and HER can be controlled by a gelling agent and concentration of potassium hydroxide (KOH) solution. Various concentrations of KOH solution and polyacrylic acid have been used for gel electrolyte. The electrolyte solution is prepared with different concentrations of KOH (6 M, 7 M, 8 M, 9 M). Among studied materials, the cell assembled with 6 M KOH gel electrolyte exhibits the highest specific discharge capacity and poor capacity retention. Whereas, 9 M KOH gel electrolyte shows high capacity retention. However, a large amount of hydrogen gas is evolved with 9 M KOH solution. In general, the increase in concentration is related to ionic conductivity. At concentrations above 7 M, the viscosity increases and the conductivity decreases. As a result, compared to other studied materials, 7 M KOH gel electrolyte is suitable for Zn-air batteries because of its higher capacity retention (92.00 %) and specific discharge capacity (351.80 mAh/g) after 6 hr storage.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1997.11a
• /
• pp.393-396
• /
• 1997

Electro Discharge Machining (EDM) is a so-call non-conventional machining technique. This paper presents the experimental results of an EDM technique for the fabircation of microholes on #7440 pyrex glans. With various applied voltages and at various concentration of KOH solution, the glass substrate have been microdrilled using the copper electrodes of which diameters are 250$\mu\textrm{m}$ to 450$\mu\textrm{m}$, respectively. The machined throughholes have been observed the top diameter, the bottom diameter, hollow width and hole diameter of the hole, and machining time hale been measured. The experimental results show that the machining time decreases as the concentration of KOH solution increases or the applied voltage increase. Also, The top diameter increases as the concentration of KOH solution decreases or the allied voltage increases. The bottom and hollow width decreases as the of KOH solution increases or the applied voltage decreases.

• Polymer(Korea)
• /
• v.37 no.5
• /
• pp.592-599
• /
• 2013

In this study, polyacrylonitrile (PAN)-based porous carbon nanofibers were prepared from PAN polymer solution by electrospinning and KOH activation with various concentrations, and the characterization of pore structures and carbon dioxide adsorption was investigated. Manufactured PAN-based activated carbon nanofibers tend to decrease diameter and increase surface oxygen functional groups depending on the increasing concentration of KOH solution. In addition, according to the results of nitrogen adsorption for pore properties analysis, it indicated increase of the specific surface area in conformity with increasing concentration of KOH solution. Micropore volume of treated activated carbon nanofibers (ANCF) by 4 M KOH was the largest compared with other samples and mesopore volume of treated ANCF by 8 M KOH was the largest volume, respectively. The concentration of KOH effects textural and surface properties, as represented by BET and XPS, which enhance carbon dioxide adsorption capacity at 0 and $25^{\circ}C$.

• Journal of the Korean institute of surface engineering
• /
• v.49 no.2
• /
• pp.119-124
• /
• 2016

Plasma electrolytic oxidation (PEO) is a promising coating process to produce ceramic oxide on valve metals such as Al, Mg and Ti. The PEO coating is carried out with a dilute alkaline electrolyte solution using a similar technique to conventional anodizing. The coating process involves multiple process parameters which can influence the surface properties of the resultant coating, including power mode, electrolyte solution, substrate, and process time. In this study, ceramic oxide coatings were prepared on commercial Al alloy in electrolytes with different KOH concentrations (0.5 ~ 4 g/L) by plasma electrolytic oxidation. Microstructural and electrochemical characterization were conducted to investigate the effects of electrolyte concentration on the microstructure and electrochemical characteristics of PEO coating. It was revealed that KOH concentration exert a great influence not only on voltage-time responses during PEO process but also on surface morphology of the coating. In the voltage-time response, the dielectric breakdown voltage tended to decrease with increasing KOH concentration, possibly due to difference in solution conductivity. The surface morphology was pancake-like with lower KOH concentration, while a mixed form of reticulate and pancake structures was observed for higher KOH concentration. The KOH concentration was found to have little effect on the electrochemical characteristics of coating, although PEO treatment improved the corrosion resistance of the substrate material significantly.

• Journal of the Korean Electrochemical Society
• /
• v.4 no.4
• /
• pp.166-171
• /
• 2001

In an aluminum-air unit cell used alkaline solution, Hydrogen evolution rates were investigated far the observation of the effects of alloy element, inhibitor and its concentration in electrolyte, KOH concentration, solution temperature, and current density loaded to cell. Hydrogen evolution rates were reduced up to $50\%$ by saturating the solution with ZnO, while ZnAc(Zinc Acetate) did not work as inhibitor. The inhibition effect of ZnO increased with increasing the KOH concentration and solution temperature. They were linearly increased with the KOH concentration and current density in first order and exponentially increased with the solution temperature.

• Journal of Korean Society of Environmental Engineers
• /
• v.34 no.1
• /
• pp.55-62
• /
• 2012

The present paper investigates the performance of the KOH aqueous solution as an absorbent to capture carbon dioxide ($CO_2$). The chemical absorption was carried out according to consecutive reactions that are generated in the order of $K_2CO_3$ and $KHCO_3$. The overall absorption was completed with following the physical absorption. When the absorption was conducted with the KOH as the limiting reactants in batch a reactor, $K_2CO_3$ production rate was the 1st order reaction for $OH^-$. However, $KHCO_3$ generation reaction was independent of the $CO_3^{2-}$ concentration and the rate was calculated to be $0.18gCO_2/min$ for all KOH absorbents, which is the same value of the reaction rate using $K_2CO_3$ aqueous solution as the absorbents. The overall $CO_2$ capture ratio of the 5% KOH absorbent was estimated to be 19% and the individual value in section 1 and 2 was 57 and 12%, respectively. The amount of $CO_2$ absorbed in the solution was very slightly less than the theoretical value, which was ascribed to the side reaction that produces $K_2CO_3{\cdot}KHCO_3{\cdot}1.5H_2O$ during the reaction and the consequent diminish in $CO_2$ absorption in the KOH solution.

• Journal of the Korean Ceramic Society
• /
• v.18 no.3
• /
• pp.147-151
• /
• 1981

On the calcium silicate hydrothermal reaction, the effect of NaOH and KOH Studied. Forincreasing the yield of fibers and to promote crystal growth, Rotary autoclae has been used. By addition NaOH solution, approximately 150${\mu}{\textrm}{m}$ of pectolite was grown. By addition KOH solution, approximately 30${\mu}{\textrm}{m}$ of 11$\AA$-Tobermorite was grown under the conditon of 21$0^{\circ}C$ 10 days reaction. These results indicate that 11$\AA$-Tobermorite was stabilized by KOH over a wide Temperature and composition range.

• Transactions of the Korean hydrogen and new energy society
• /
• v.33 no.4
• /
• pp.330-336
• /
• 2022

In order to evaluate the possibility as a separator in alkaline water electrolysis, the high temperature characteristics were evaluated by measuring the membrane resistance and durability of 5 types of commercial anion exchange membranes in 7 M KOH solution and at 80℃. The membrane resistance of AEM membrane measured in 7 M KOH solution and at 80℃ had a lower value of about 8-24 times compared to the other membranes. The durability of AEM membrane tested with the soaking time in 7 M KOH solution and at 80℃ showed a very good stability and that of FAAM40 and FAAM75-PK showed secondly a good stability. The thermal stability with the soaking time in 7 M KOH solution and at 80℃ of FAAM40 and FAAM75-PK membrane analyzed by thermo-gravimetric analysis showed a good stability compared to the other membranes.

• Journal of the Korean Crystal Growth and Crystal Technology
• /
• v.5 no.3
• /
• pp.278-283
• /
• 1995

The potassium titanate fibres were synthesized with wet process by the addition of KOH solution to the TiOz gel produced by the reaction between element titanium particles and $H_2O_2$ solution at $50^{\circ}C$. And then they were characterized by XRD, SEM and FT - IR. It was found that potassium titanate fibres were mainly affected by KOH/TiOz mole ratio, synthesis time and aging time in this wet process employed. For $KOH/TiO_2 = 1/1$, synthesizing time 24 hrs, aging time 24 hrs and calcination temperature of TEX>$900^{\circ}C$ for 1 hr, their products were mainly found to be potassium tetratitanate which had thin and long fibres in the range of 10 ~ 20 mm. As the synthesizing time increased and the amount of KOH decreased, potassium tetratitanate was converted into potassium hexatitanate. Also, the length of their fibres became short.