• 한국가스학회지
• /
• 제26권2호
• /
• pp.9-13
• /
• 2022

벨트나 체인을 이용한 감속기는 간단한 장치이긴 하지만 공간을 많이 차지하여 공간상의 제약이 있기 때문에 전동휠체어 구동부에는 부적합하다. 하지만 유성기어형태의 감속기는 동일 축에서 감속이 이루어지기 때문에 부피를 작게 할 수 있어 공간의 제약이 벨트나 체인형태의 감속기보다 덜하다. 따라서 본 연구에서는 수·전동전환이 가능한 휠체어의 구동부에 대한 연구를 통하여 유성기어형태를 이용한 감속기로 큰 추진력을 얻을 수 있는 구동부를 개발하였다. 그에 따라 감속기에 적용되는 유성기어의 치형을 Kisssoft 프로그램을 이용하여 설계를 진행하였다. 또한 기존 휠체어 바퀴에 적용 가능하도록 구동부의 설계를 진행하였고, 구동부의 수·전동 전환원리 및 작동원리에 대한 메커니즘의 최적화를 진행하였다. 연구내용을 토대로 하나의 선기어와 2개의 유성기어, 하나의 링기어를 갖는 유성기어 형태의 휠체어 감속기 구동부의 최종 설계 및 제작을 진행하였다.

• 드라이브 ㆍ 컨트롤
• /
• 제17권1호
• /
• pp.1-12
• /
• 2020

This study was to develop a simulation model of a compound planetary gear reducer for the final driving shaft using a gear analysis software (KISSsoft, Version 2017, KISSsoft AG, Switzerland). The aim of this study is to analyze transmission error and the tooth load distribution through micro-geometry using the simulation model. The tip and root relief were modified with Micro-geometry in the profile direction, and crowning was modified with Micro-geometry in the lead direction. The transmission error was analyzed using the PPTE (Peak to Peak Transmission Error) value, and the tooth load distribution was analyzed for the concentrated stress on the tooth surface. As a result of modifying tip and relief in the profile direction, the transmission error was reduced up to 40.7%. In the case of modifying crowning in the lead direction, the tooth load was more evenly distributed than before and decreased the stress on the tooth surface. After modifying the profile direction for the 1st and 2nd planetary gear train, the bending and contact safety factors were increased by 31.7% and 17%, and 18.3% and 12.5% respectively. Moreover, the bending and safety factors after modifying lead direction were increased by 59.5% and 32.7%, respectively for the 1st planetary gear train, and 59.6% and 43.6%, respectively for the 2nd planetary gear train. In future studies, the optimal design of a compound planetary gear reducer for the final driving shaft is needed considering both the transmission error and tooth load distribution.

• International journal of advanced smart convergence
• /
• 제9권3호
• /
• pp.199-206
• /
• 2020

A wheelchair is an essential rehabilitation assistant device for the movement of paraplegia patients and generally paralyzed patients who cannot walk normally. In particular, the applicability of the manual/motorized wheelchair is gradually increasing. Until now, decelerators using belt, chain and worm gears, etc have been widely used. However, a decelerator takes a large space although it is a simple device and thus is not ideal for the driving part of manual/motorized wheelchair. For these reasons, in this study we developed a driving part producing a large driving force through a decelerator using planetary gears rather than conventional worm gear-based decelerator. We designed the tooth profile of the planetary gears for decelerator using Kisssoft program, In addition, we designed the driving part so as to apply it to the wheels of conventional wheelchairs, and then optimized the mechanism for the principles of manual/motorized transposition of the driving part and the operational principles. Based on the results of this study, we finally designed and manufactured a driving part for wheelchair decelerator in the form of planetary gears with 1 sun gear, 2 planetary gears and 1 ring gear.

• 한국기계가공학회지
• /
• 제18권12호
• /
• pp.7-14
• /
• 2019

A marine turning gear controls the position of the piston-crank mechanism by rotating the flywheel of the marine engine at a low speed, which is the main auxiliary machine that enables the disassembly and maintenance of the engine. In this study, the safety factor for surface durability and tooth bending strength was improved by the design modification of the marine turning gear based on the spur planetary gear. Angular velocity, torque, and efficiency of the turning gear were measured using a reliability evaluation tester, and a multibody dynamics model for analysis corresponding to the test results was developed. Finally, it was confirmed that the design improvements improved the tooth surface damage of the sun gear in the 3^rd reduction stage.

• 한국기계가공학회지
• /
• 제19권10호
• /
• pp.36-43
• /
• 2020

A marine turning gear is the main auxiliary machine that enables the disassembly of and maintenance on the main engines. In this study, a marine turning gear based on a helical planetary reducer was developed through analysis of a marine turning gear based on a spur planetary reducer. Nonlinear numerical analysis was performed to determine the ideal contact ratio between the sun gear and the idle gear. Based on this, the surface durability, tooth bending strength, and contact ratio were calculated. In addition, the helix direction was selected to utilize the existing bearings. Gears were manufactured based on the helical gear design values, and the turning gear was evaluated using the FTA standards of MAN Co. Ltd. As a result, a lifetime of 3,000 to 5,000 hours was verified, the maximum torque measured was 105kNm, and the efficiency was measured to be 87.4%.

• 한국기계가공학회지
• /
• 제20권5호
• /
• pp.8-16
• /
• 2021

This study develops a shaft analysis model for the optimization of the power transmission system. The finite element method was used for the shaft analysis model. The shaft and gear were assumed Timoshenko beams. Strength was evaluated according to DIN 743, and gear misalignment was calculated through ISO 6336 and the coordinate system rotation. The analysis software for a power transmission system was developed using Visual Studio 2019. The analysis results of the developed program were compared with those of commercial software (MASTA, KISSsoft, and Romax). We confirmed that the force, deformation, and safety factors at each node were the same as those of the commercial software. The absolute value of the gear misalignment of the developed program and commercial software was different. However, the gear misalignment tended to increase with increasing the displacement in the tooth width direction.

• 농업과학연구
• /
• 제43권4호
• /
• pp.656-664
• /
• 2016

Gear reducers are widely used for various agricultural machinery applications such as greenhouses, tractors, and agricultural vehicles. However, thermal deformation and surface pitting at gear tooth flank frequently occur in gear reducers due to high torque. Thus, surface heat treatment of gears is required to improve wear and fatigue resistance. The objective of this study was to simulate the load capacity of the agricultural gear reducer. The simulation was performed for the following three surface heat treatment methods: untreated gears, nitriding heat treatment, and induction hardening method, those mostly used for agricultural gear reducers. The load capacity of the gear reducer was simulated using the safety factor, limit bending stress, and limit contact stress of the gear. The simulation of the load capacity was conducted using KISSsoft commercial software for gear analysis. The main results of simulation test were as follows: first, the nitriding heat treatment resulted in the highest safety factor for bending stress, which was increased about 77% from those of the untreated gears. Second, the induction hardening was the highest safety factor for contact stress, which was increased about 150% from those of the untreated gears. The safety factor for contact stress of the induction hardening was increased about 64% from those of the nitriding heat treatment. The study result suggested that the surface heat treatments could enhance load capacity and that the method of surface heat treatment should be determined based on simulation results for appropriate use scenarios.

• 농업과학연구
• /
• 제46권4호
• /
• pp.723-735
• /
• 2019

The power-train is the most important component of an agricultural tractor. In this study, the strength of the driving gear transmission of an 82 kW-class tractor was analyzed using equivalent torque during plow tillage. The load measurement system consisted of an engine revolution speed sensor, torque-meters, revolution speed sensors for four axles, and pressure sensors for two hydraulic pumps. The load data were measured during plow tillage for four speed stages: F2 (2.78 km/h), F5 (5.35 km/h), F7 (7.98 km/h), and F8 (9.75 km/h). Aspects of the gear-strength such as bending stress, contact stress, and safety factors were analyzed under two torque conditions: the equivalent torque at the highest plow load for the F8 speed stage and the maximum engine torque. The simulation results using KISSsoft showed that the maximum engine torque conditions had a lower safety factor than did the highest equivalent torque condition. The bending safety factors were > 1 at all gear stages, indicating that gear breakage did not occur under actual measured operating conditions, nor under the maximum torque conditions. However, the equivalent torque condition in the contact stress safety factor was > 1, and the maximum torque condition was < 1 at the first gear pair. The method of analysis using the equivalent torque showed lower stress and higher safety factor than did the method using maximum torque. Therefore, when designing a tractor by applying actual working torque, equivalent torque method would support more reliable product development.

• 농업과학연구
• /
• 제43권3호
• /
• pp.441-449
• /
• 2016

Agricultural tractors are designed using the empirical method due to the difficulty of measuring precise load cycles under various working conditions and soil types. Especially, directly drives various tractor implements, the power take off (PTO) gear. Therefore, alternative design methods using gear design software are needed for the optimal design of tractors. The objective of this study is to simulate fatigue life of the PTO gear according to the operating point of the tractor engine. The PTO gear was made with SCr415 alloy steel with carburizing and quenching treatments. The fatigue life of the PTO gear was simulated by using bending and contact stress according to the torque of the load levels. The PTO gear simulation was conducted by the KISSsoft commercial software for gear analysis. Bending and contact stress were calculated by the ISO 6336:2006 Method A and B. The simulation of fatigue life was calculated by the Miner's cumulative damage law. The total fatigue life of tractors can be estimated to 3,420 hours; thus, 3,420 hours of fatigue life were used in the simulation of the PTO gear of tractors. The main simulation results showed that the maximum fatigue life of the PTO gear was infinite fatigue life at maximum engine power. Minimum fatigue life of the PTO gear was 19.61 hours at 70% of the maximum engine power. Fatigue life of the PTO gear changed according to load of tractor. Therefore, tractor work data is needed for optimal design of the PTO gear.

• 한국농업기계학회:학술대회논문집
• /
• 한국농업기계학회 2017년도 춘계공동학술대회
• /
• pp.15-15
• /
• 2017

본 연구는 필드 작업 시 작업조건에 따른 정식기의 PTO 부하를 측정하고, 이를 이용하여 작업조건에 따른 안전율 시뮬레이션을 목적으로 수행하였다. 부하 계측 시스템은 PTO 축의 부하를 측정하기 위한 토크 센서, 토크 센서에서 발생한 신호를 수집하기 위한 데이터 수집장치, 노트북에 전원을 공급하기 위한 파워 컨트롤러로 구성하였다. 토크센서에서 입력된 부하 데이터를 처리하기 위한 소프트웨어는 Labview(Version 2011, National Instrument, USA)를 사용하였다. 포장시험은 유사한 토양 조건에서 4회 반복 시험을 수행하였으며, 작업속도 고속 조건에서 4개의 주간거리(26, 35, 43, 80cm)와 3개의 식부깊이 (85, 105, 136mm)에 대하여 수행하였다. 안전율 시뮬레이션을 위한 소프트웨어는 KISSsoft(Version 2016, Kissling & Co. AG, Switzerland)를 사용하였다. 식부깊이 85mm에서 주간거리 26, 35, 43, 80cm일 때 작업시 각각 굽힘 안전율은 2.2874, 2.4507, 2.7139, 2.8064로 나타났으며 접촉 안전율은 1.1787, 1.2799, 1.3205, 1.3275로 나타났다. 식부깊이 105mm에서 주간거리 26, 35, 43, 80cm일 때 작업 시 각각 굽힘 안전율은 2.1261, 2.2781, 2.4879, 2.5866로 나타났으며 접촉 안전율은 1.1296, 1.1425, 1.2710, 1.2507로 나타났다. 식부깊이 136mm에서 주간거리 26, 35, 43, 80cm일 때 작업 시 각각 굽힘 안전율은 1.6587, 1.6651, 1.7824, 2.2198로 나타났으며 접촉 안전율은 1.0030, 1.0104, 1.0450, 1.1931로 나타났다. 주간거리에 따른 식부깊이의 굽힘 안전율과 접촉 안전율은 가장 차이가 큰 주간거리 80cm에서 식부깊이가 85, 105, 136mm일 때 작업 시 각각 굽힘 안전율은 2.8064, 2.5866, 2.2198로 나타났으며 접촉 안전율은 1.3275, 1.2507, 1.1931로 나타났다. 시뮬레이션 결과 정식기 베벨기어의 안전율은 주간거리가 짧을수록, 식부깊이가 깊을수록 더 낮게 나타났다. 그러므로 정식 작업 시 정식기의 부하와 내구성을 고려하여 적절한 작업조건을 선정해야 함을 알 수 있다. 또한 향후 다양한 토양 조건 및 작업 단수 등에 따른 포장시험을 추가로 진행하여 여러 조건에서의 안전율 시뮬레이션을 수행할 예정이다.