• Transactions of the Korean Society of Automotive Engineers
• /
• v.15 no.3
• /
• pp.133-140
• /
• 2007

The purpose of this study was to evaluate the effects of gasoline fuel to the LPI engine. Firing test bench was used in order to assess the effect on gasoline-injected LPI engine. Gasoline fuel was supplied into the reverse direction(3-4-2-1 cylinder) at 3.0 bar with commercial gasoline fuel pump. Engine test was performed using the firing test mode at end of line. The deviations of excess air ratio of each cylinder and maximum combustion pressure using gasoline fuel were within 0.1 and $1{\sim}2\;bar$. Engine start time was measured with changing coolant temperature at $20^{\circ}C,\;40^{\circ}C,\;80^{\circ}C$, respectively. Residual gasoline volume in the fuel line was measured about 32 cc after firing test and it was less than 2 cc within 10 seconds purging. To simulate the end of line, the residual gasoline in the fuel line was purged during 5 and 10 seconds. Start time of LPI engine with LPG fuel were 0.61 and 0.58 seconds. This work showed that severe problems such as misfiring and liner scuffing were not occurred applying gasoline fuel to LPI engine.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.2
• /
• pp.72-82
• /
• 2005

The objective of this paper is to describe the optimization of design parameters in a large-sized commercial bus heater system by using CFD(computational fluid dynamics) analysis and Taguchi method. In order to obtain the best combination of each control factor which results in a desired performance of heater system, the parameter design of the Taguchi method is adopted for the robust design considering the dynamic characteristic. The research activity may be divided into four phases. The first one is analyzing the problem, i.e., ascertaining the influential factors. In the second phase the levels were set in such a way that their variation would significantly influence the response. In the third phase the experimental runs were designed. In the final phase the planned runs were carried out numerically to evaluate the optimal combination of factors which is able to provide the best response. In this study, eight factors were considered for the analysis: one with two level and seven with three level combinations comprising the $L_{18}(2^1{\times}3^7)$ orthogonal array. The results of this study can be summarized as follows ; (i)The optimum condition of control factor is a set of <$A_2\;B_1\;C_3\;D_3\;E_1\;F_2\;G_3\;H_2$> where A is shape of the outer fin, B is pitch of the outer fin, C is height of the outer fin, D is the inner fin number, E is the inner fin height, F is length of the flame guide, G is diameter of the heating element and H is clearance between air guide and heating element. (ii)The heat capacity of heated discharge air under the optimum condition satisfies the equation y=0.6M w here M is a signal factor. (iii)The warm-up rate improves about three times, more largely as com pared with the current condition, which results in about 9.2minutes reduction.

• Journal of Korea Port Economic Association
• /
• v.35 no.4
• /
• pp.147-168
• /
• 2019

This paper explores strategies for building an automobile logistics cluster in PyeongtaekDangjin Port, which needs to be developed and operated for automobile related value-added logistics services. The future of Korean automobile exports seems gloomy, but many domestic ports, including PyeongtaekDangjin Port, are struggling to secure a position as automobile ports by expanding port facilities to attract exports and transshipment vehicles. PyeongtaekDangjin Port is currently the best automobile port as it is under good conditions for building an automobile logistics cluster. Ssangyong Motor Co., Kia Motors Corp., Samsung Electronics Co., and LG Electronics Inc., which are located nearby, can secure enough land to build an automobile logistics cluster by developing a port distribution complex in the future. This will promote the sustainable development of PyeongtaekDangjin Port by creating a logistics hub, specifically an automobile logistics hub, which would allow diverse cultures and experiences to respond appropriately to future mobility development.

• Advanced Composite Materials
• /
• v.17 no.3
• /
• pp.259-275
• /
• 2008

This study aims to optimize the mechanical and electrical properties of electrically conductive polymer composites (CPCs) for use as a material of bipolar plates for PEM fuel cells. The thin CPCs consisting of conductive fillers and polymer resin were fabricated by a preform molding technique. Expanded graphite (EG), flake-type graphite (FG) and carbon fiber (CF) were used as conductive fillers. This study tested two types of CPCs, EG/FG filled CPCs and EG/CF filled CPCs, to optimize the material properties. First, the characteristics of EG/FG filled CPCs were investigated according to the FG ratio for 7 and $100{\mu}m$ sized FG. CPCs using $100{\mu}m$ FG showed optimal material properties at 60 wt% FG ratio, which were an electrical conductivity of 390 S/cm and flexural strength of 51 MPa. The particle size was an important parameter to change the mechanical and electrical behaviors. The flexural strength was sensitive to the particle size due to the different levels of densification. The electrical conductivity also showed size-dependent behavior because of the different contributions to the conductive network. Meanwhile, the material properties of EG/CF filled CPCs was also optimized according to the CF ratio, and the optimized electrical conductivity and flexural strength were 290 S/cm and 58 MPa, respectively. The electrical conductivity of this case decreased similarly to the EG/FG filled case. On the other hand, the behavior of the flexural strength was more complicated than the EG/FG filled case, and the reason was attributed to the interaction between the strengthening effect of CF and the deterioration of voids.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.13 no.6
• /
• pp.105-112
• /
• 2005

This study aims at evaluating the environmental impacts stemmed from the End-of-Life Vehicle(ELV) treatment systems in Korea, using Life Cycle Assessment(LCA) method. In this study, both environmental burden from the ELV dismantling process & recycling processes and environmental benefit which were derived from the avoided environmental impacts by substituting recycled materials for virgin materials were considered. First of all, the key issues which were defined as the environmental aspects that account for more than $1\%$ out of the total environmental impacts were identified from the Life Cycle Impact Assessment(LCIA). $CO_2$, crude oil, natural gas, coal, etc. were found out to be the key issue parameters. From the LCI Analysis and LCIA studies, it was shown that the significant environmental aspects were related with the recycling process of ferro scrap, the shredding process of compressed car bodies and the dismantling process of end-of-life engines. In particular, the recycling process of ferro scrap has the most significant effects on the environmental impacts of the ELV treatment systems. Based on these results, it is recommended to improve the recycling process of ferro scrap in order to make the ELV treatment systems more environmentally sound.

• Journal of Sensor Science and Technology
• /
• v.5 no.6
• /
• pp.15-24
• /
• 1996

In this study, as a part of the basic study for the application of optical fiber sensors to smart composite structures, the integrity of optical fiber sensors embedded within the composite structures was examined and then the laser signal transmitted through optical fiber sensors during the deformation of host structures was investigated. Firstly, it was found that bending test could be substituted for tensile test by comparing cumulative failure distribution based on weakest link theory and introducing the correction factor. Weibull parameters were obtained through the experiments and the correction factor was found to be applied to cumulative failure distribution derived from bending test. The integrity of embedded optical fiber sensors due to the thermal effect was evaluated by the comparison of the mean tensile strengths of cured and uncured optical fibers. Secondly, relationships between stress-strain curve obtained in tensile test of composite laminate and the intensity of laser signal transmitted through embedded optical fibers were examined and the possibility of the effective damage detection using optical fiber sensors was studied.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.19 no.11
• /
• pp.521-528
• /
• 2018

Military vehicles use run-flat wheels for emergency situations. Run-flat wheels can run required distance in a defined duration with the pressure loss tire. For the application of a run-flat system, wheels are designed in 2 pieces, including an inner rim and outer rim. These rims are assembled using clamping bolts. Clamping bolts determine the durability of military vehicle wheels because fracture of clamping bolts account for most wheel failures. For improving wheel durability, clamping bolt durability must be improved. In this study, wheel test conditions and bolt design were investigated. Existing test standards are not sufficient to conduct endurance tests. Supplementary conditions were investigated. Using these modified test conditions, the durability of wheels including clamping bolts was tested and verified. Results found the durability of wheels improved more than 168%. This study also proposes improvements in the design process of clamping bolts.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.20 no.12
• /
• pp.24-29
• /
• 2021

Recently, owing to the high demand for eco-friendly cars in the automotive industry, noise and vibrations have become major challenges. The use of laminated damping steel is increasing in response to these demands. Laminated damping steel is primarily used in sound insulation plates. The vibration energy is converted into thermal energy due to the viscoelastic resin being located between two steel sheets and being able to damp the vibrations when an external force, such as, noise or vibration is applied to the steel plate. Laminated damping steel is chiefly applied to dash panels in automotive body parts, and because of its structure, junction technology for bonding with other components is necessary. However, there has not been sufficient research conducted on junctions. In this study, regardless of the electrode shape, in the range of 4.0 ~ 8.0 kA welding current, the same welding force and welding time were applied which were 2.8 kN and 200 m/s (12 cycles) and the tensile shear load and nugget size were analyzed after the resistance spot welding between different materials of laminated damping steel with a thickness of 1.035 mm. The results show that in the range of 5 ~ 8 kA welding current, 1.035 mm laminated damping steel meets the MS181-15 standard, which is the technical standard of Hyundai-Kia Motors.

• Information Systems Review
• /
• v.22 no.4
• /
• pp.59-74
• /
• 2020

This paper investigates the asymmetric effect of social sentimental on an individual stock price return. For this purpose, four companies such as POSCO, Korean Electricity, AMORE PACIFIC, KIA Motors are chosen from KOSPI listed companies in terms of dataperspective. The main estimation results are as follows: the positive opinions affect only the stock prices return of three companies while the negative opinions affect all of the companies. It shows that positive or negative texts give asymmetric effect on stock price return and the effect of negative opinions is bigger than that of positive opinions. The results imply that investors are more sensitive to the negatives since they have the tendency of loss aversion. Also, it indicates that subjective opinion on SNS can be used as the proxy for the investment sentiment.

• Journal of Venture Innovation
• /
• v.1 no.2
• /
• pp.35-46
• /
• 2018

The research on the efficiency analysis of domestic auto parts companies is mostly based on the calculation of the magnitude of the performance creation such as the sales amount compared to the input assets. However, the performance indicators such as sales, operating profit, and net profit are directly related to the cost structure and This cost structure is affected by changes in the firm's asset and capital structure. As a result, it is considered that efficient capital procurement needs to be done at the same time to create efficient management performance through proper investment. This study focuses on this point and attempts to measure the efficiency of procurement capital relative to the sales and other performance indicators generated by the first 33 suppliers who supply parts to Hyundai Kia Motors. Among the methods of evaluating efficiency, the DEA model based on the linear programming method is most widely used as a nonparametric method but The efficient frontier-based DEA model has the limitation that it can not use the variables that have a downward influence on the efficiency. This is inadequate to directly consider variables such as borrowings and total liabilities related to capital procurement. In this study, the efficiency of capital procurement was measured using Worst Practice DEA and the improvement direction of the capital procurement aspect of domestic auto parts companies was suggested