• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.497-502
• /
• 2018

In Korea, passenger car and van using LPG fuel including taxi constantly increased due to the high cost of fuel. Recently, the emission standard has continuously tightened in the world. In this investigation was conducted the greenhouse gas emission characteristics of LPG vehicles according to the displacement and weight. Exhaust emission characteristics of 13 test LPG vehicles from about 1.0 L to 3.0 L displacements were measured and analyzed by using chassis dynamometer and emission analyzer. It is revealed that the greenhouse gas emission was showed the increasing tendency as the displacement and curb weight increased. Also, greenhouse gas emission of SC03 driving cycle has highest value and that of HWFET driving cycle shows the lowest value.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.538-548
• /
• 2018

The thermo-acoustic instability in the combustion process of a gas turbine is caused by the interaction of the heat release mechanism and the pressure perturbation. These acoustic vibrations cause fatigue failure of the combustor and decrease the combustion efficiency. This study is to develop a segmented dynamic thermo-acoustic model to understand combustion instability of gas turbine. Therefore, this study required a dynamic analysis rather than static analysis, and developed a segmented model that can analyze the performance of the system over time using the Matlab/Simulink. The developed model can confirm the thermo-acoustic combustion instability and exhaust gas concentration in the combustion chamber according to the equivalent ratio change, and confirm the thermo-acoustic combustion instability for the inlet temperature and the load changes. As a result, segmented dynamic thermo-acoustic model has been developed to analyze combustion instability under the operating condition.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.411-418
• /
• 2018

The polymer electrolyte membranes, CL-SPEEK/Cellulose composite membrane I, II, III with the improved electrochemical and mechanical properties were prepared and characterized. The engineering plastic polyether ether ketone (PEEK) and cellulose were sulfonated and cross-linked. The membranes were prepared by sol-gel casting method with different amount of cross-linking reagent. In conclusion, the composite membranes I, II, III showed improved thermostability, tensile strength and oxidative durability. Proton conductivity of the membranes was also improved and the composite membrane I showed 0.1312 S/cm at $80^{\circ}C$ which was the best of those composite membranes.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.512-522
• /
• 2018

This study was conducted to investigate on the combustion characteristic with the effects of mat thickness and fuel kinds in a metal-fiber burner. The mode transition point is confirmed by the K value, which was defined as the rate of flow velocity and laminar burning velocity. The ($T^4_{sur}-T^4_{\infty}$) is highest at methane flame with 3 T thickness. Through the measurement of the unburned mixture temperature, the possibility of submerged flame in surface combustion burner was confirmed. The rapid emission of CO occurs nearby limit blow out (LBO) because of the increase of flow velocity. In case of NOx, the trend is similar with surface temperature. However, it also considered that the NOx emission is affected by residence time with flame position.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.458-465
• /
• 2018

This study reports the fabrication of anion exchange membranes (AEMs) containing two kinds of functional groups: i) trimethylphosphite (TMP) and ii) trimethylamine (TMA). We carried out the synthesis of polymers to enhance thermal stability and ion conductivity. The alternative polymer was prepared using 2,2-bis(4-hydroxy-3-methylphenyl)propane and decafluorobiphenyl. The membrane was fabricated by solution casting method. The thermal stability of membranes was examined by TGA. The physiochemical properties of membranes were also investigated in terms of water uptake, swelling ratio, ion exchange capacity, and ion conductivity. The hydroxide ion conductivity of the membranes reached about 20.2 mS/cm for quaternary ammonium poly(arylene ether) (QA-PAE) containing TMA moiety and 5.1 mS/cm for quaternary phosphonium PAE (QP-PAE) containing TMP moiety at $90^{\circ}C$.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.434-441
• /
• 2018

The pore size of nickel (Ni) bottom electrode layer (BEL) for low-temperature solid oxide fuel cells embedded with ultrathin-film electrolyte was controlled by changing the substrate surface morphology and deposition process parameters. For ~150-nm-thick Ni BEL, the upper side of an anodic aluminum oxide (AAO) substrate with ~65-nm-sized pores provided ~1.7 times smaller pore size than the lower side of the AAO substrate. For ~100-nm-thick Ni BEL, the AAO substrate with ~45-nm-sized pores provided ~2.6 times smaller pore size than the AAO substrate with ~95-nm-sized pores, and the deposition pressure of ~4 mTorr provided ~1.3 times smaller pore size than that of ~48 mTorr. On the AAO substrate with ~65-nm-sized pores, the Ni BEL deposited for 400 seconds had ~2 times smaller pore size than the Ni BEL deposited for 100 seconds.

• Transactions of the Korean hydrogen and new energy society
• /
• v.29 no.5
• /
• pp.466-472
• /
• 2018

The investigation of cryogenic liquid pool spreading is an essential procedure to assess the hazard of cryogenic liquid usage. In this experimental study, to measure the evaporation velocity when the pool is spreading, liquid nitrogen was continuously released onto unconfined concrete ground. Almost all of the reported results are based on a non-spreading pool in which cryogenic liquid is instantaneously poured onto bounded ground for a very short period of time. A simultaneous measurement of the pool location using thermocouples and of the pool mass using a digital balance was carried out to measure the evaporation velocity and the pool radius. A greater release flow rate was found to result in a greater average evaporation velocity, and the evaporation velocity decreased with the spreading time and the pool radius.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.3
• /
• pp.311-317
• /
• 2016

This paper presents the flow characteristics of a ball valve used for a gas pipeline. Understanding of the internal flow of a ball valve is an important to analyze the physical phenomena of the valve. Present experimental study was performed by IEC 60534-2-3, the international standard for an industrial control valve testing procedure. Pressure measured at upstream and downstream of the valve, flow-rate and gas temperature passing the inside of the gas pipeline were measured with respect to valve opening rates. Throughout the experimental measurement of the ball valve, empirical equation of the pressure drop between the ball valve according to the mass flow rates is successively obtained using a polynomial curve fitting method. In addition, flow coefficient for determining the valve capacity is also analyzed with respect to valve opening rates using the curve fitting method.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.3
• /
• pp.306-310
• /
• 2016

In Na-base Battery for ESS, ${\alpha}-Al_2O_3$ and metal bonding was used to prevent direct reaction between electrolyte and electrode. The hard metal was metalized at $1600^{\circ}C$ in a flowing hydrogen gas for high bonding strength. In this study, instead of hard metal metalizing, Ni was plated on ${\alpha}-Al_2O_3$ by electroless Ni plating technique and then bonded with metal. To enhance the bonding strength, surface of ${\alpha}-Al_2O_3$ was treated with $H_3PO_4$. The effects of strength and leakage of joining as a function of acid treatment time on ${\alpha}-Al_2O_3$ are described.

• Transactions of the Korean hydrogen and new energy society
• /
• v.27 no.2
• /
• pp.176-181
• /
• 2016

Recent years, supercapacitors have been attracting a growing attention as an efficient energy storage, due to their long-lifetime, device reliability, simple device structure and operation mechanism and, most importantly, high power density. Along with the increasing interest in flexible/stretchable electronics, the supercapacitors with compatible mechanical properties have been also required. A eutectic gallium-indium (EGaIn) liquid metal could be a strong candidate as a soft electrode material of the supercapacitors because of its insulating surface oxide layer for electric double layer formation. Here, we report the electrochemical study on the charging/reaction process at the interface of EGaIn liquid metal and electrolyte. Numerical fitting of the charging current curves provides the capacitance of EGaIn/insulating layer/electrolyte (${\sim}38F/m^2$). This value is two orders of magnitude higher than a capacitance of a general metal electrode/electrolyte interface.