• Journal of the Korean Recycled Construction Resources Institute
• /
• v.5 no.3
• /
• pp.320-326
• /
• 2017

This study is based on the hot air welding application method of EVA sheet to test the tensile strength performance changes due to the hot air welding speed, temperature and chemical attack. For the parameters of the study, the hot air welding method that directly heats the overlap between the sheets and the adhesion surface was controlled, and the maximum temperature for application was set to $20^{\circ}C$, $0^{\circ}C$, $-5^{\circ}C$, $-10^{\circ}C$. According to the results of the testing, the tensile strength of the overlap area was the highest between the temperatures of 20 at 5~6m/min and between the low temperatures at 3~4m/min of hot air welding speed.

• Journal of Korean Society of Coastal and Ocean Engineers
• /
• v.25 no.5
• /
• pp.291-300
• /
• 2013

Typhoon simulation method is widely used to estimate sea surface wind speeds during the typhoon periods. Holland (1980) model has been regarded to provide relatively better results for observed wind data. JTWC or RSMC best track data are available for typhoon modeling, but these data show slightly different because the data generation process are different. In this paper, a Newton-Raphson method is used to solve the two nonlinear equations based on the Holland model that is formed by the two typhoon parameters, i.e. the longest radius of 25 m/s and 15 m/s wind speeds, respectively. The solution is the radius of maximum wind speed which is of importance for typhoon modeling. This method is based on the typhoon wind profile of JMA and it shows that Holland model appears to fit better the characteristics of typhoons on the temporal and spatial changes than that of the other models. In case of using RSMC best track data, the method suggested in this study shows better and more reasonable results for the estimation of radius of maximum wind speed because the consistency of the input data is assured.

• Journal of the Korea Concrete Institute
• /
• v.18 no.3 s.93
• /
• pp.321-330
• /
• 2006

In order to remodel old aged reinforced concrete buildings, it is often required to extend the residence area of the buildings by increasing the slab area. The slab area is usually extended by attaching a new slab to the existing slab with hinged joint or rigid joint. Transmission of the loads of the attached slabs to the existing slabs depends on the connecting methods, such as hinged or rigid connection. In this research, 8 specimens and 24 RC slabs connected by rigid joints were tested. The new slab was connected to the existing slab by three types of rigid joints using dowel bars and longitudinal tensile bars. Main parameters of the slabs were three types of the rigid joints, anchor length of steel bars(0, 50, 60, 100, and 120mm), development length of steel bars(100, 200, and 300mm), and the spacing of the steel bars(150, 200, 300, and 450mm). The test results indicated that the flexural strength of the RC test slabs having various types of rigid joints was approximately the same to that of the slab without any connections.

• Proceedings of the KWS Conference
• /
• 2010.05a
• /
• pp.51-51
• /
• 2010

Recently just as in the automobile industry, shipbuilders also try to reduce material consumption and weight in order to keep operating costs as low as possible and improve the speed of production. Naturally industry is ever searching for welding techniques offering higher power, higher productivity and a better quality. Therefore it is important to have a details research based on the various welding process applied to steel and other materials, and to have the ability both to counsel interested companies and to evaluate the feasibility of implementation of this process. Submerged-arc welding (SAW) process is usually used about 20% of shipbuilding. Similar to gas metal arc welding(GMAW), SAW involves formation of an arc between a continuously-fed bare wire electrode and the work-piece. The process uses a flux to generate protective gases and slag, and to add alloying elements to the weld pool and a shielding gas is not required. Prior to welding, a thin layer of flux powder is placed on the work-piece surface. The arc moves along the joint line and as it does so, excess flux is recycled via a hopper. Remaining fused slag layers can be easily removed after welding. As the arc is completely covered by the flux layer, heat loss is extremely low. This produces a thermal efficiency as high as 60% (compared with 25% for manual metal arc). SAW process offers many advantages compared to conventional CO2 welding process. The main advantages of SAW are higher welding speed, facility of workers, less deformation and better than bead shape & strength of welded joint because there is no visible arc light, welding is spatter-free, fully-mechanized or automatic process, high travel speed, and depth of penetration and chemical composition of the deposited weld metal. However it is difficult to application of thin plate according to high heat input. So this paper has been focused on application of the field according to SAW process for thin plate in ship-structures. For this purpose, It has been decided to optimized welding condition by experiments, relationship between welding parameters and bead shapes, mechanical test such as tensile and bending. Also finite element(FE) based numerical comparison of thermal history and welding residual stress in A-grade 3.2 thickness steel of SAW been made in this study. From the result of this study, It makes substantial saving of time and manufacturing cost and raises the quality of product.

• Journal of the Korean Arthroscopy Society
• /
• v.9 no.2
• /
• pp.201-205
• /
• 2005

Purpose: The purpose of this study is to evaluate the result of arthroscopic excision of painful Os subtibiale and Os subfibulare. Materials and Methods: Sixteen patients who had accessory bone in the ankle joint were treated by arthroscopy. Os subtibiale was four cases and os subfibulare twelve. The average follow-up period was 9 months$(range:6{\sim}42months)$. All patients were evaluated clinically with physical examination and radiologically with simple X-ray and for further evaluation, eight with bone scan, three with computed tomography and twelve with magnetic resonance image. We estimated the result of resection with Ogilvie-Harris's criteria. Results: All parameters of subjective and functional evaluation were improved with statistical significance(p<0.05). At final evaluation, eight patients still complained of mild pain and among them, three patients for synovitis, three for tendinitis on MRI and two for incomplete resection. Conclusion: The arthroscopic resection is a very effective method for painful os subtibiale and subfibulare using small incisions and for treatment of associated lesion. The preoperative radiological evaluation is essential and magnetic resornance image is useful for detecting of associated lesion.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.40 no.10
• /
• pp.1976-1985
• /
• 2015

The amount of packets in palyout buffer of video streaming receiver can be changed by network condition, and saturated and exhausted by the delay and jitter. Especially, if the amount of incoming video traffic exceeds the maximum allowed playout buffer, buffer overflow problem can be generated. It makes the deterioration of video image and the discontinuity of playout by skip phenomenon. Also, if the incoming packets are delayed by network confusion, the stop phenomenon of video image is made by buffering due to buffer underflow problem. To solve these problems, this paper proposes the video streaming receiver with token bucket scheme which automatically establishes the important parameters like token generation rate r and bucket maximum capacity c adapting to the pattern of video packets. The simulation results using network simulator-2 (NS-2) and joint scalable video model (JSVM) show that the proposed token bucket scheme with automatic establishment parameter provides better performance than the existing token bucket scheme with manual establishment parameter in terms of the generation number of overflow and underflow, packer loss rate, and peak signal to noise ratio (PSNR) in three test video sequences.

• Journal of the Mineralogical Society of Korea
• /
• v.3 no.1
• /
• pp.1-6
• /
• 1990

Clacic amphiboles along the tremolite (Tr)-tschermakite(Ts) joint were synthesized using a piston-cylinder appratus. At 750-85$0^{\circ}C$and 12-2 kb, amphibole+corundum coexist with zoisite($\pm$talc, chlorite, and Mg-staurolite), but with anorthite($\pm$cholorite, spinel, pyroxenes, and sapphirine) at lower P. At 90$0^{\circ}C$, amphibole+corundum+clinopyroxene($\pm$anorthite, forsterite, sapphirine, and garnet) are stable over the P range 12-18 kb. These amphibole-bearing assemblages are replaced at high P by clcinopyroxene+talc+chlorite+zoisite at 650-75$0^{\circ}C$, and at higher temperatures by garnet+clinopyroxene($\pm$zoisite, orthopyroxene, and Mg-staurolite). Synthetic amphiboles with Ts>~45 mol% contain as much as 0.15 excess cations per formula unit(pfu) based on 23 oxygens(anhydrous formula), whereas less tschermakitic ones are deficient in cation occupancy by up to 0.18 pfu. This trend is attributed to the 야/trioctahedral substitution in Ca-amphiboles. Compositions of synthetic amphiboles display systematic changes with P and T governed by coexisting mineral assemblages. The Ts content (=[8-Si-Na]/2) increases with increasing T( Ts/ T=~0.1 nik% K-1) in the range 750-85$0^{\circ}C$, but remains nearly constant at 850-90$0^{\circ}C$. Pressure dramatically affects the Ts content of Ca-amphiboles:it increases with P at 8-12 kb( Ts/ T=2-3 mol% K-1), but significantly decreases at 12-21 kb( Ts/ P=-2.5 mol% Kb-1). Hence, the most tschermakitic amphiboles, containing 60$\pm$5 mol % Ts, or 1.2$\pm$0.1 tetrahedral Al, occur at 12 kb and 850-90$0^{\circ}C$. Compositions of Ca-amphiboles defined by a simple reaction, 3 Tr+2 zoisite+7 corundum+H2O=5 Ts, are reversed and used to estimate thermodynamic parameters of tschermakite assuming ideal mixing of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$of Tr-Ts solid solutions. Predicted standard molal entropy and enthalpy of tschermakite are : S$^{\circ}$=566.9$\pm$13.7 J mol-1K, -1and H$^{\circ}$=-12518.36$\pm$15.17 kJ mol.-1

• Journal of Gastric Cancer
• /
• v.16 no.1
• /
• pp.21-27
• /
• 2016

Purpose: Transducer-like enhancer of split 1 (TLE1) is a member of the Groucho/TLE family of transcriptional co-repressors that regulate the transcriptional activity of numerous genes. TLE1 is involved in the tumorigenesis of various tumors. We investigated the prognostic significance of TLE1 expression and its association with clinicopathological parameters in gastric cancer (GC) patients. Materials and Methods: Immunohistochemical analysis of six tissue microarrays was performed to examine TLE1 expression using 291 surgically resected GC specimens from the Soonchunhyang University Cheonan Hospital between July 2006 and December 2009. Results: In the non-neoplastic gastric mucosa, TLE1 expression was negative. In GC, 121 patients (41.6%) were positive for TLE1. The expression of TLE1 was significantly associated with male gender (P=0.021), less frequent lymphatic (P=0.017) or perineural invasion (P=0.029), intestinal type according to the Lauren classification (P=0.024), good histologic grade (P<0.001), early pathologic T-stage (P=0.012), and early American Joint Committee on Cancer stage (P=0.022). In the Kaplan-Meier analysis, the TLE1 expression was significantly associated with longer disease-free (P=0.022) and overall (P=0.001) survival rates. Conclusions: We suggested that TLE1 expression is a good prognostic indicator in GCs.

• Journal of the Microelectronics and Packaging Society
• /
• v.15 no.4
• /
• pp.77-86
• /
• 2008

The reliability of leaded and lead-free solders of BGA type packages on a printed circuit board was investigated by employing the standard drop test and 4-point bending test. Tested solder joints were examined by optical microscopy to identify associated failure mode. Three-dimensional finite element analysis(FEM) with ANSYS Workbench v.11 was carried out to understand the mechanical behavior of solder joints under the influence of bending or drop impact. The results of numerical analysis are in good agreement with those obtained by experiments. Packages in the center of the PCB experienced higher stress than those in the perimeter of the PCB. The solder joints located in the outermost comer of the package suffered from higher stress than those located in center region. In both drop and bending impact tests, the lead-free solder showed better performances than the leaded solders. The numerical analysis results indicated that stress and strain behavior of solder joint were dependent on various effective parameters.

• Journal of Korean Society of Steel Construction
• /
• v.26 no.4
• /
• pp.263-275
• /
• 2014

In this study, connection of steel reinforced concrete(SRC) column and composite beam which consists of H-section and U-section members were tested under cyclic loading. An essential point of the composite beam is the structural performance of welded joint between the H-section and the U-section members. To improve the structural performance of joint of two beam members, vertical stiffeners, trapezoidal stiffeners, and top bars were used. Five full-scaled specimens were designed to study the effect of a number of parameters on cyclic performance of connections such as H-section beam size($H-500{\times}200{\times}10{\times}16$, $H-600{\times}200{\times}11{\times}17$), the presence of stiffeners and top bars, and the presence of no weld access hole(WAH) method. Based on the test results, deformation capacity of the specimens with H-500 series beam and H-600 series beam were 4% and 3% rotation angle, which is the requirement for the Special Moment Frame and Intermediate Moment Frame(IMF), respectively. Test result showed that deformation capacity of connection with stiffeners and top bars is greater than that of connection without stiffeners and top bars. Finally, energy dissipation capacity and strain profile of specimens were summarized.