• Transactions of the Korean Society of Automotive Engineers
• /
• v.18 no.6
• /
• pp.84-90
• /
• 2010

This paper presents the shape optimization process for the automotive wheel bearing seal lip using the finite element method and the response surface method. First, to predict performance of the bearing seal lip, we used the non-linear finite element analysis. And then, we compared the analysis results with the test results to verify the finite element model. The objective function in optimizing process was obtained from results of the mud slurry test, which is one of many tests for evaluating performance of wheel bearing. After the mud slurry test for the four models which have the similar cross-sectional shape, we measured the wear area of the seal lip and the moisture content in grease. The objective function has been chosen by comparing the results of mud slurry test and characteristics of seal lip, such as contact force, contact area, contact pressure, and interference. Finally, within limited design parameters, we suggested the optimized shape of seal lip, which is expected to improve the wear and the sealing effect of it.

• Tribology and Lubricants
• /
• v.31 no.3
• /
• pp.125-140
• /
• 2015

In this paper, we present the results of the wear analysis of journal bearings on a stripped-down single-cylinder engine during start-up and coast-down by motoring. We calculate journal bearing wear by using a modified specific wear rate considering the fractional film defect coefficient and load-sharing ratio for the asperity portion of a mixed elastohydrodynamic lubrication (EHL) regime coupled with previously presented graphical data of experimental lifetime linear wear in radial journal bearings. Based on the calculated wear depth, we obtain a new oil film thickness for every crank angle. By examination of the oil film thickness, we determine whether the oil film thickness at the wear scar region is in a mixed lubrication regime by comparing dimensionless oil film thickness, h/σ, to 3.0 at every crank angle. We present the lift-off speed and the crank angles involved with the wear calculation for bearings #1 and #2. The dimensionless oil film thickness, h/σ, illustrates whether the lubrication region between the two surfaces is still within the bounds of the mixed lubrication regime after scarring of the surface by wear. In addition, we present in tables the asperity contact pressure, the real minimum film thickness at the wear scar region, the modified specific wear rate, and the wear angle, α, for bearings #1 & #2. To show the real shape of the oil film at wear scar region, we depict the actual oil film thickness in graphs. We also tabulated the ranges of bearing angles related with wear scar. We present the wear volume for bearings #1 and #2 after one turn-on and turn-off of the engine ignition switch for five kinds of equivalent surface roughness. We show that the accumulated wear volume after a single turn-on and turn-off of an ignition switch normally increases with increasing surface roughness, with a few exceptions.

• Tribology and Lubricants
• /
• v.9 no.2
• /
• pp.63-69
• /
• 1993

The wear properties of two types of $Si_3N_4$(silicon nitride) exposed to high and low humidity were examined experimentally for various sliding speed. Bearing steel was used as the disk material at pin-on-disk type sliding. Wear rates of pressureless sintered-plus-hot-isostatic pressed Si3N4 were slightly lower than those of pressureless sintered $Si_3N_4$. It was observed that adsorbed moisture and sliding speed markedly influenced the wear properties of $Si_3N_4$. The highest wear rate was obtained under the high humidity and low sliding speed condition. As the sliding speed was increased, wear rates were decreased and the humidity effect on the wear rates of $Si_3N_4$ was lowered. The result that the $Si_3N_4$ pin showed a high wear rate under the high humidity condition was explained by the property change due to the adsorbed moisture, plowing action by the hard particles of $Fe_2O_3$ from the disk, and the corrosion effect at $Si_3N_4$ surface. Increase in sliding speed was supposed to have reduced the humidity effect on wear rate of $Si_3N_4$ by raising the temperature of both the bearing steel disk and $Si_3N_4$ pin specimen.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.18 no.10
• /
• pp.2597-2605
• /
• 1994

The wear behavior of two types of $Si_3N_4$ exposed to high and low humidity was examined at various sliding speeds, using bearing steel as disk material under pin-on-disk type sliding conditions. Higher wear rates were obtained at a high humidity than at a low humidity. As the sliding speed was increased, the wear rates were decreased and the effect of humidity on the wear rates of $Si_3N_4$ was reduced. The result that the $Si_3N_4$ pin showed higher wear rate under the high humidity condition was explained by the decrease in microhardness of $Si_3N_4$ due to the chemisorbed moisture on the pin and plowing action by the hard particles of $Fe_2O_3$ from the disk. An increase in the sliding speed is supposed to reduce the effect of humidity on the wear rate of $Si_3N_4$ by raising the average temperature of the disk surface and the local temperature at pin-disk contact point.

• Proceedings of the Korean Society For Composite Materials Conference
• /
• 2004.04a
• /
• pp.63-66
• /
• 2004

In this study, a hybrid composite journal bearing composed of carbon fiber reinforced phenolic composite liner and metal backing was manufactured to solve the seizure problem of metallic journal bearing materials because the carbon fiber has self-lubricating ability and the phenolic resin has thermal resistance characteristics. To estimate the wear resistance of carbon fiber phenolic composite, wear tests were performed at several pressures and velocities. The oil absorption characteristics, coefficient of thermal expansion, strength and stiffness of the composite were also tested. Using the measured stiffness values, the thermal residual stresses in the composite were calculated to check the reliability of the composite journal bearing.

• Journal of Power Electronics
• /
• v.8 no.2
• /
• pp.181-191
• /
• 2008

The task performed by induction motors grows increasingly complex in modern industry and hence improvements are sought in the field of fault diagnosis. It is essential to diagnose faults at their very inception, as unscheduled machine down time can upset critical dead lines and cause heavy financial losses. Artificial intelligence (AI) techniques have proved their ability in detection of incipient faults in electrical machines. This paper presents an application of AI techniques for the detection of inter-turn insulation and bearing wear faults in single-phase induction motors. The single-phase induction motor is considered a proto type model to create inter-turn insulation and bearing wear faults. The experimental data for motor intake current, rotor speed, stator winding temperature, bearing temperature and noise of the motor under running condition was generated in the laboratory. The different types of fault detectors were developed based upon three different AI techniques. The input parameters for these detectors were varied from two to five sequentially. The comparisons were made and the best fault detector was determined.

• Journal of the Korean Society for Heat Treatment
• /
• v.34 no.3
• /
• pp.130-136
• /
• 2021

With the development of the industry, bearings that require higher durability and efficiency are required, and various methods to reduce friction and wear of bearings are being studied. In this study, a wear test was conducted for STB2, a bearing steel material, by machining a micro-line pattern on the race surface of the bearing by machining. The pattern pitch of the specimens was processed to 40㎛, 80㎛, and 150㎛, and the coefficient of friction characteristics were investigated for the unpatterned specimen and the specimen with a DLC thin film deposited on the surface. As a result of the wear test, the pattern pitch showed the smallest coefficient of friction at 40㎛, and it was confirmed that the smaller the pattern pitch, the better the tribology characteristics.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.5
• /
• pp.1-7
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• Journal of the Korean Society of Manufacturing Process Engineers
• /
• v.11 no.4
• /
• pp.25-30
• /
• 2012

The transportation is almost dependent on a single fuel petroleum with transportation energy dilemma. Hybrid Electric Vehicle(HEV) technology holds more advantages on efficiency improvements for petroleum consumption at the transportation. And bearing is recognized as the important component of gearbox. Gearboxes for HEV transmission have been ensured the highest reliability over some years in withstanding high dynamic loads. At the same time, the demands of lightweight design and cost minimization are required by thought-out design, high-quality material, superior production quality and maintenance. In order to design a reliable and lightweight gearbox, it is necessary to analyze bearing rating life methods between standard and different bearing companies with calculation methods for modification factors. In this paper, the influence of life time of bearings will be pointed out. Bearing contact stress and load stress distribution of HEV gearbox are obtained and compared with Romaxdesigner and BearinX. And the unequal wear of the left bearing for the gearbox intermediate shaft is investigated between simulation and test.

• Journal of Mechanical Science and Technology
• /
• v.17 no.2
• /
• pp.215-220
• /
• 2003

Trepan prevents the wear of the inside part of a bearing when the initial shaft rotates. It continuously contacts with the eccentric part of the shaft in rotation and is loaded repeatedly. Therefore, even if an early crack of a trepan part is small, the crack may progress by the repeated load. If the crack progresses, very small chips come out. This Is put in the rotor and prevents the rotation of the compressor, There can be leaks in a microgroove and extreme wear can occur due to lack of oil on the surface contact part. Therefore, this study was carried out to compare and investigate the trepan strength and deflection characteristics between trepan locations and dimension changes using the finite element method and search a motor bearing for a model with bigger stiffness of a trepan part and the same deflection.