• 한국소음진동공학회논문집
• /
• 제12권5호
• /
• pp.338-345
• /
• 2002

The study presents a new testing and analysis method for brake judder on vehicle. For the identification of the excitation mechanism of a brake judder, it is necessary to measure the dynamic brake disc geometry during braking on vehicle. The non-contact sensor system was used to monitor the brake disc geometry. Brake torque variation (BTV) caused by disc thickness variation (DTV) is the primary excitation for brake judder. The mechanical effects generating BTV are linked not only to initial manufacturing tolerances but also to uneven wear. Therefore, the brake disc geometry should be strictly managed to initial condition. The aim of this study has been to measure the dynamic DTV and runout on vehicle and analyze the influence of test parameters on brake judder and compare the disc component with vehicle matching about the DTV Profile. As a result of this study, The amplitude of brake judder is proportional to vehicle speed and fluid pressure fluctuation on braking. The major sources of brake judder are directly related to disc thickness variation and side runout variation of corner assembly (disc, hub. bearing).

• 대한기계학회논문집A
• /
• 제37권11호
• /
• pp.1387-1395
• /
• 2013

차륜 불평형은 차륜의 무게중심이 윤축의 기하학적 중심축에서 벗어나 있을 때 발생한다. 차륜 불평형을 수정하지 않고 주행하면 불평형에 의한 원심력이 차체의 진동을 발생시키게 되며 차륜의 마모를 촉진시키거나 차축 베어링에 손상을 주게 된다. 본 연구에서는 철도차량 동적해석을 통하여 차륜 불평형이 차량 임계속도와 차체 진동에 미치는 영향을 검토하였다. 차륜 불평형은 임계속도를 감소시키고 차체 공진을 유발할 수 있음을 알 수 있었다. 또한 차륜의 정적, 동적 불평형에 따른 차체진동을 해석함으로써 불평형 수정은 양면 밸런싱이 필요함을 밝혔다.

• Macromolecular Research
• /
• 제17권8호
• /
• pp.603-608
• /
• 2009

Novel ultra-high molecular weight polyethylene (UHMWPE)/zirconia composites were previously prepared by the in situ polymerization of ethylene using a Ti-based Ziegler-Natta catalyst supported on to the surface of zirconia, as a bearing material for artificial joints. Tribological tests revealed that a uniform dispersion of zirconia in UHMWPE markedly increased the wear resistance. The effects of zirconia content on the oxidation behavior of the ${\gamma}$-ray-treated UHMWPE/zirconia composite surfaces were examined. The oxidation index that estimates the oxidation degree as the content of total carbonyl compounds was monitored using Fourier transform infrared spectroscopy-attenuated total reflectance. The changes in the surface composition due to the oxidation were confirmed by electron spectroscopy for chemical analysis. The extent of oxidation decreased with increasing zirconia content, which was attributed to the increased crystallinity as well as the decreased polymer portion of the UHMWPE/zirconia composites.

• Archives of Reconstructive Microsurgery
• /
• 제19권2호
• /
• pp.88-92
• /
• 2010

The forefoot reconstruction is a challenging field for plastic surgeons. Weight bearing tolerability and stability are important factor of choosing reconstruction methods, but cosmetic aspect has to be considered. 51 year old man visited our clinic with extensive degloving injury on right forefoot by roller. The soft tissue defect started from metatarsal area to the toe tip including nails. We harvested the anterolateral thigh flap and transferred it to the forefoot defect area with nerve coaptation. The flap was successful without skin necrosis or other complications. Secondary flap debulking surgery was performed after ten months from initial operation. Patient was satisfied with functional and cosmetic outcomes. The patient was able to wear shoes and walk with adequate sensory recovery. As there is few report about reconstruction of forefoot soft tissue defects, we report a unique case of the anterolateral thigh innervated free flap reconstruction in degloving injury.

• Tribology and Lubricants
• /
• 제36권6호
• /
• pp.359-364
• /
• 2020

Numerical investigation of the groove trap effect with variation in the groove-edge radius of curvature is presented here. The trap effect is evaluated in a two-dimensional sliding bearing using computational fluid dynamics (CFD). This simulation is based on the discrete phase model (DPM) and standard k - ε turbulence model using commercial CFD software, FLUENT. The numerical results are evaluated by comparisons with streamlines and particle trajectories in the grooves. Grooves are applied to various lubrication systems to improve their lubrication characteristics, such as load carrying capacity increment, leakage reduction, frictional loss reduction, and preventing three-body abrasive wear due to trapping effect. This study investigates the grove trapping effect for various groove-edge radius of curvature values and Reynolds numbers. The particle is assumed to be made of steel, with a circular shape, and is injected as a single particle in various positions. One-way coupling is used in the DPM model because the single particle injection condition is applied. Further, the "reflect" condition is applied to the wall boundary and "escape" condition is used for the "pressure inlet" and "pressure outlet" boundaries. From the numerical results, the groove edge radius is found to influence the groove trap effect. Moreover, the groove trap effect is more effective when applying the groove edge radius.

• 열처리공학회지
• /
• 제21권1호
• /
• pp.10-19
• /
• 2008

To investigate the effect of ultrasonic nano-crystalline surface modification (UNSM) treatment on rolling contact fatigue and residual stress properties of bearing steels, this paper carried out a rolling contact fatigue test, measured residual stress and retained austenite, performed a wear test, observed microstructure, measured micro hardness, and analyzed surface topology. After the UNSM treatment, it was found that the surface became minute by over $100{\mu}m$. The micro surface hardness was changed from Hv730~740 of base material to Hv850~880 with about 20% improvement, and hardening depth was about 1.3 mm. The compressive residual stress was measured as high as -700~-900 MPa, and the quantity of retained austenite was reduced to 27% from 34%. The polymet RCF-6 ball type rolling contact fatigue test showed over 4 times longer fatigue lifetime after the UNSM treatment under 551 kgf load and 8,000 rpm. In addition, this paper observed the samples, which went through the rolling contact fatigue test, with OM and SEM, and it was found that the samples had a spalling phenomenon (the race way is decentralized) after the UNSM treatment. However, before the treatment, the samples had excessive spalling and complete exploration. Comparison of the test samples before and after the UNSM treatment showed a big difference in the fatigue lifetime, which seems to result from the complicated effects of micro particles, compressive residual stress, retained austenite, and surface topology.

• 대한금속재료학회지
• /
• 제46권8호
• /
• pp.477-481
• /
• 2008

The secondary hardening and fracture behavior in P/M high speed steels bearing V content of 9 to 10 wt% have been investigated in terms of austenitizing temperature and precipitation behavior. Austenitizing was conducted at 1,100 and $1,175^{\circ}C$ of relatively low and high temperatures. Coarse primary carbides retained after austenitization were mainly V-rich MC type. They give a significant influence on hardeness and toughness, as well as wear resistance. Tempering was performed in the range of $500{\sim}600^{\circ}C$. The peak hardness resulting from the precipitation of the fine MC secondary carbides was observed near 520, irrespective of austenitizing temperature. Aging acceleration(or deceleration) did not occur with increasing austenitizing temperature because it mainly influences contents of V and C of matrix through the dissloution of coarse primary MC containing lots of V and C. The precipitation of secondary MC carbides, which also contain V and C, did not change the aging kinetics itself. In the 10V alloy containing much higher C content, the impact toughness was lower than 9V alloy, because of the larger amount of primary carbide and high hardness.

• 공업화학
• /
• 제2권4호
• /
• pp.356-362
• /
• 1991

가황계에 따른 NR/BR 블렌드의 물리적 기계적 특성의 변화를 가교밀도의 차이로 해석하였다. 경화제의 비율 및 함량이 증가함에 따라 가황속도 및 최대 토오크는 증가를 보였으며, 가교밀도도 증가하였다. 가교밀도의 증가에 따라 경도, 300% 모듈러스, 반발탄성 및 마모특성은 증가를 보인 반면에 발열에 의한 온도 상승 및 $60^{\circ}C$에서의 tan $\delta$는 감소를 보였다. 따라서 높은 하중이 가해지는 트럭/버스 타이어의 트레드 부위에 사용하는 경우 회전저항이 적은 semi-EV 가황계가 가장 적절한 가황 시스템으로 판단되었다.

• Tribology and Lubricants
• /
• 제36권1호
• /
• pp.11-17
• /
• 2020

In manufacturing operations, oil plays a crucial role in reducing friction and wear among interacting surfaces at varying velocities, loads, and temperature. Hydrocarbon oil is considered the origin of lubrication oils. However, this base oil has been limited in its use as it is a principal cause of pollution. This research focuses on identifying a biodegradable base oil lubricant that possesses a stable coefficient of friction and viscosity with temperature. Friction analysis is conducted by employing a pin on a disk tribotester with a fixed load of 10 N at varying sliding speeds ranging from 0.06 m/s to 0.34 m/s. Oil viscosity analysis is perfomed at room temperature by using a rotary viscometer. Tests are performed using canola oil and paraffin oil as lubricants. The results indicate that the viscosity of canola oil is more efficient than paraffin oil. The non-dimensional characteristic number according to the Stribeck curve reveals an elastohydrodynamic lubrication regime with canola oil lubrication. A comparison of both lubricants reveals that, the friction efficiency of canola oil and paraffin oil does not differ considerably. However, the friction in canola oil is observed to decrease more than that in paraffin oil at an elevated sliding speed. The tests confirm that canola oil is potent in minimizing the friction coefficient of SCM440 bodies interacting with one another as well as acted upon by load.

• Tribology and Lubricants
• /
• 제28권3호
• /
• pp.136-141
• /
• 2012

In this paper, we investigated the friction characteristics of $W100^{\circ}{\o}L25m$ ellipse type surface pattern, on bearing steel. These characteristics are researched by utilizing a pin-on-disk wear test machine, under various velocities and other conditions. The reduction of friction is a necessary requirement for the improved efficiency of industrial parts. As the speed increases, there is a decrease in the effect of the dimple of friction characteristic in low velocity, with substantially little change to density. Conversely, as the load increases, the test direction of ellipse type dimple pattern, resulting in a difference in the texture of these two components. At a dimple density of 7.5% the friction characteristic is easily demonstrated, with a consistent change in both speed and load.