• Journal of Korean Tunnelling and Underground Space Association
• /
• v.10 no.2
• /
• pp.119-128
• /
• 2008

In the case of a circular shaft, it is expected that asymmetric loads should apply on the surface rather than symmetric loads due to geographical factors and the non-homogeneity of the jointed rock masses. In this study, discontinuous numerical analysis was carried in order to analyze the characteristics of asymmetric load distribution on the wall of the circular shaft due to anisotropy caused by heterogeneity of rock masses affected by the discontinuities like as a Joint. And it was also analyzed that the effect of the mechanical properties varied with the rock mass rating and horizontal stress with depth had influence in the asymmetric load on the wall of the shaft. In the case of considering the effect of the joint as variable, asymmetric load ratio $(R_p)$, which was defined as the ratio of the load subtracted minimum from maximum to minimum, was below 25% in the hard rock. As regarding the variation of the rock mass rating with depth as variable, the value of $R_p$ was below than 25% in the hard rock, and the value between 30% and 40% in the soft rock. On the other hand, the $R_p$ of fractures rock was between $45{\sim}50%$ which value was much higher than that in better rock mass rating.

• Tunnel and Underground Space
• /
• v.10 no.2
• /
• pp.180-195
• /
• 2000

Grouting has been practiced as a reliable technique to improve the mechanical properties of rock mass. But, the study of ground improvement by greeting is rare especially in jointed rock mass. In this study, joint compression test and direct shear test were performed on pure rock joint and cement milk grouted rock joint to examine the grouting effect on the property of rock joint. In the pure rock joint compression test, joint closure varied non-linearly with normal stress. But after cement milk grouting, the normal deformation characteristics of the joint was linear at the low normal stress level. As normal stress increased. deformation of the sample rapidly increased due to the stress concentration at the joint asperities. Peak shear strength of the grouted joint in low normal stress was higher than that of non-grouted joint due to the cohesion, decreased exponetially as the grout thickness increased. Thus after cement milk grouting, the failure envelope modified to a curve that has cohesion due to grout material hydration with decreased friction angle. Shear stiffness and peak dilation angle of the grouted joint decreased as the grout thickness increased. The peak shear strength from the direct shear test on grouted rock joint was represented by an empirical equation as a fuction of grout thickness and roughness mean amplitude.

• Proceedings of the Korean Society for Noise and Vibration Engineering Conference
• /
• 2013.04a
• /
• pp.690-691
• /
• 2013

• Proceedings of the KSEEG Conference
• /
• 2001.04a
• /
• pp.175-180
• /
• 2001

• Interaction and multiscale mechanics
• /
• v.4 no.1
• /
• pp.49-64
• /
• 2011

A methodology for jointed rock mass characterization starts with a research based on geological data and tests in order to define the geotechnical models used to support the decision about location, orientation and shape of cavities. Afterwards a more detailed characterization of the rock mass is performed allowing the update of the geomechanical parameters defined in the previous stage. The observed results can be also used to re-evaluate the geotechnical model using inverse methodologies. Cases of large underground structures modeling are presented. The first case concerns the modeling of cavities in volcanic formations. Then, an application to a large station from the Metro do Porto project developed in heterogeneous granite formations is also presented. Finally, the last case concerns the modeling of large cavities for a hydroelectric powerhouse complex. The finite element method and finite difference method software used is acquired from Rocscience and ITASCA, respectively.

• Proceedings of the Korean Geotechical Society Conference
• /
• 1993.10b
• /
• pp.235-247
• /
• 1993

The 62 m span Olympic lee Hockey cavern in Gjovik, Norway, is located in jointed gneiss of average RaD = 70% and has a rock cover of only 25 to 50m, thus posing challenging design p problems. The investigations prior to construction included two types of stress measurements, cross-hole seismic tomography, special coe logging, Q-system classification and numerical modelling with UDEC-BB. Predicted maximum deformations were 4 to 8 mm; surprisingly small due to the high horizontal stresses recorded. Extensometer (MPBX) installations from the surface prior to construction, precision surface levelling and MPBX installed from inside the cavern give a combined measure of maximum deformations in the range 7 to 8 mm with the 62 m span fully e excavated, and three adjacent caverns for the Postal Services also completed.

• Tunnel and Underground Space
• /
• v.20 no.5
• /
• pp.352-359
• /
• 2010

Stability of twin tunnels depends on the pillar width and the ground condition. In this study, large scale model tests were conducted for investigating the influence of the pillar width of twin tunnels on their behavior in the regular horizontal jointed rock mass. Jointed rocks was composed of concrete blocks. Pillar width of twin tunnels varied in 0.29D, 0.59D, 0.88D and 1.18D, where D is the tunnel width. During the test, pillar stress, lining stress, tunnel distortion, and ground displacement were measured. Lateral earth pressure coefficient was kept in a constant value 1.0. As a result, it was found that the pillar stress and the displacement of the ground and tunnel were increased by decreasing pillar width. The maximum displacement rate was measured just after the upper excavation in each construction sequence. And the maximum influence position was the right shoulder of the preceeding tunnel at the pillar side. It was also found that for the stability assessment the inner displacement was more critical than the crown displacement. The influence zone was formed at the pillar width 0.59D~0.88D that was smaller than 0.8D~2.0D, which was proposed by experience for a good ground condition. And it would be concluded that horizontal joints could also influence on the stability of the twin tunnels.

• Geomechanics and Engineering
• /
• v.13 no.4
• /
• pp.535-570
• /
• 2017

There are only few cases where cause and location of failure of a rock structure are limited to a single discontinuity. Usually several discontinuities of limited size interact and eventually form a combined shear plane where failure takes place. So, besides the discontinuities, the regions between adjacent discontinuities, which consist of strong rock and are called material or rock bridges, are of utmost importance for the shear strength of the compound failure plane. Shear behaviour of persistent and non-persistent joint are different from each other. Shear strength of rock mass containing non-persistent joints is highly affected by mechanical behavior and geometrical configuration of non-persistent joints located in a rock mass. Therefore investigation is essential to study the fundamental failures occurring in a rock bridge, for assessing anticipated and actual performances of the structures built on or in rock masses. The purpose of this review paper is to present techniques, progresses and the likely future development directions in experimental testing of non-persistent joint failure behaviour. Experimental results showed that the presence of rock bridges in not fully persistent natural discontinuity sets is a significant factor affecting the stability of rock structures. Compared with intact rocks, jointed rock masses are usually weaker, more deformable and highly anisotropic, depending upon the mechanical properties of each joint and the explicit joint positions. The joint spacing, joint persistency, number of rock joint, angle of rock joint, length of rock bridge, angle of rock bridge, normal load, scale effect and material mixture have important effect on the failure mechanism of a rock bridge.

• Tunnel and Underground Space
• /
• v.12 no.4
• /
• pp.291-303
• /
• 2002

In this study, three-dimensional block generation program was developed using the discontinuities input data for three-dimensional mechanical and hydro-mechanical analysis. Shi's two dimensional theory and program was extended to those of three-dimension and the deformations of blocks were calculated. The two-dimensional hyro-mechanical theory of DDA was also extended to three-dimensional theory and coupling deformation of the underground cavern was analyzed considering discontinuities.

• Tunnel and Underground Space
• /
• v.5 no.1
• /
• pp.11-21
• /
• 1995

일반적으로 NATM공법에서 지보의 설계는 암반반응곡선의 개념을 통해 수행된다. 그러나 암반반응곡선은 암질이 좋고 과지압에 의한 문제가 심각하지 않은 지역에 적용되며, 따라서 주로 불연속면에 의해 암반의 거동이 영향을 받는 지역에서는 시공과정에 직접 적용하기가 힘들다. 본 연구에서는 암반 블록에 대한 블록반응곡선을 연구하여, 블록반응곡선상에서 지보를 설계하였다. 각각의 차분시각에서의 변위와 응력을 얻기위해서 개별요소 프로그램인 UDEC을 사용하였다. 블록은 Mohr-Coulomb 모델이며, 불연속면은 Barton-Bandis 모델이다. 블록과 불연속면의 물성은 실험실 실험을 통하여 구하였다. 블록반응곡선을 이용한 지보설계과정을 이해하기 위하여 간단한 모델분석을 실시하였다. 동일한 형상의 키블록이 공동의 천장, 측벽, 바닥에 존재할 경우, 각 블록의 안정성 판단 및 지보의 설계를 실시하였다. 또한 초기지압의 영향을 알아보기 위하여, 측압계수(K)를 달리하여 해석해보았다. 현재 건설중인 공동에 대한 안정성 판단 및 지보설계를 블록반응곡선을 이용하여 설계하였다.