• Proceedings of the Korean Institute of Building Construction Conference
• /
• 2012.05a
• /
• pp.65-67
• /
• 2012

The butt-joint system is widely used as the method of roof composite waterproofing system. However, there is stilll no objective research about proper distance, and proper structure associated with the performance in butt-joint system. In this research, we find proper distance and proper structure in butt-joint system through tensile strength test at joint, and comparative analyze with practical construction material of composite waterproofing sheet.

• Proceedings of the Korea Concrete Institute Conference
• /
• 2000.10b
• /
• pp.977-982
• /
• 2000

As a newly structural system, RCS composite system has been researched last two decades. However mechanism of exterior T-type joint for RCS composite system is not well known. This research is focus on the exterior T-type joint for RCS composite system. Specimens are designed by the ASCE guideline, tested and compared with the inner RCS joint. Test variables include face bearing plate(FBP), extended face bearing plate(E-FBP) and U-bar. The tests indicate that the strength of exterior T-type joint is higher than that of the guideline by ASCE. The U-bar has a significant effect on the joint strength and absorbing the strain energy.

• Journal of the Korean Geotechnical Society
• /
• v.31 no.12
• /
• pp.59-69
• /
• 2015

This study examined the magnitude and distribution of earth pressure on the support system in a jointed rock mass due to the different joint sets as well as varying the rock type and joint condition (joint shear strength and joint inclination angle). Based on a physical model test and its numerical simulation, a series of numerical parametric analyses were conducted using a discrete element method. The results showed that the induced earth pressure was affected significantly by a joint set depending on the inclusion of the joint inclination angle, which induces a joint sliding condition, but the number of joint sets alone was not important, even though the earth pressure could be increased slightly as the number of joint sets is increased. In addition, the study results were compared with Peck's earth pressure for soil ground, which indicated that the earth pressure in a jointed rock mass could be considerably different from that in soil ground. The study suggests that the effects of joint sets as well as rock type and joint condition are important factors affecting the earth pressure in a jointed rock mass and they should be considered when designing a support system in a jointed rock mass.

• International Journal of Reliability and Applications
• /
• v.12 no.2
• /
• pp.103-116
• /
• 2011

A series-parallel system with independent but non-identical components is considered. The expressions have been derived for the joint reliability importance (JRI) of m (${\geq}2$) components, chosen from a series-parallel system. JRIs of components of two different series-parallel systems are studied analytically and graphically.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1180-1185
• /
• 2004

The purpose of this study is to develop a Multi-joint rehabilitation system (CMRS : C&R Lab. Multi-joint Rehabilitation System). This study presents the mechanism of rehabilitation system that enables rehabilitation of multi-joint with kinematical analysis for joints of human body. Also, the relative positioning between human subjects and the head part to rehabilitate for the mechanism is based on robotics and anatomy. This study was verified with simulations. Finally, Automation of positioning was realized. Rehabilitation exercises in passive mode were enabled with the results.

• Journal of the Korea institute for structural maintenance and inspection
• /
• v.22 no.4
• /
• pp.91-99
• /
• 2018

Mechanical Properties of Rock Slope as a safe and effective interpretation should be thoroughly investigated. Clinometer, however, this new measurement due to the restrictions of the research for the joint orientation is needed. In this study, characteristics of the joint orientation can be used to analyze the joint orientation of developing a joint survey system that can be applied to the field. The system is developed and Analysis software to hardware. Hardware is composed to measure the joint orientation of measuring module, measuring the transfer of data transfer module. From the software is measuring module from the data to analyze the orientation of the joint development, and drone joint orientation survey system named. Can not be measured by the investigation, including regional development approach is a system that has been difficult if the Field Application of the lab test results of the joint orientation and effectively.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2004.10a
• /
• pp.1160-1165
• /
• 2004

The purpose of this study was to calculate three dimensional angular displacements, moments and joint reaction forces of the ankle joint during the waist pulling, and to assess the ankle joint reaction forces according to different perturbation modes and different levels of perturbation magnitude. Ankle joint model was assumed 3-D ball and socket joint which is capable of three rotational movements. We used 6 cameras, force plate and waist pulling system. Two different waist pulling systems were adopted for forward sway with three magnitudes each. From motion data and ground reaction forces, we could calculate 3-D angular displacements, moments and joint reaction forces during the recovery of postural balance control. From the experiment using falling mass perturbation, joint moments were larger than those from the experiment using air cylinder pulling system with milder perturbation. However, JRF were similar nevertheless the difference in joint moment. From this finding, we could conjecture that the human body employs different strategies to protect joints by decreasing joint reaction forces, like using the joint movement of flexion or extension or compensating joint reaction force with surrounding soft tissues. Therefore, biomechanical analysis of human ankle joint presented in this study is considered useful for understanding balance control and ankle injury mechanism.

• Proceedings of the Korean Society of Tribologists and Lubrication Engineers Conference
• /
• 2001.06a
• /
• pp.265-270
• /
• 2001

Hip joint simulator which Is an essential device for evaluating the wear of biomaterials (ultrahigh molecular weight polyethylene, Co-Cr alloy, alumina, etc.) used in total hip joint replacement was developed. This hip joint simulator mimics the joint motion and joint loading of human gait by adapting the 4 degree of freedom in kinematic motion (flexing/extension, adduction/abduction, Internal rotation/external rotation) and axial loading, Four stations are operated by 8 servo-motors and harmony drives. Joint leading was imposed by displacement control from a ball screw, LM guide, and spring system. Each kinematic link system operates separately or coupled modes. A heater and a thermocouple were installed for keeping the body temperature in each station.

• Knowledge Management Research
• /
• v.9 no.2
• /
• pp.109-127
• /
• 2008

This cross-level study of 77 samples from Korean 1st-tier suppliers participating in knowledge-sharing networks examined the impact of partnering(joint establishment of goal and joint problem solving system) on supplier relationship outcomes(competativeness improvement and innovative idea suggestion). The findings showed that joint establishment of goal and joint problem solving system were positively related to both supplier's competativeness improvement and its innovative idea suggestion. Whereas, joint problem solving system did account for a significant variance only in innovative idea suggestion. The findings, further, demonstrated that mutual trust moderated the relationship between joint problem solving system and supplier relationship outcomes. Implications for theory and practice are suggested.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2001.04a
• /
• pp.631-634
• /
• 2001

In this study, the graphic simulation system of multi joint manipulator is developed to analyze and optimize the remote handling processes for the spent fuel assembly. This system consists of a 3-D graphical modeling system, a device assembling system, and a motion simulation system. To analyze and optimize the processes involved in multi-joint manipulator operation such as NFBC transportation process and bottom nozzle removal process, the virtual work place is implemented using a computer graphic technology. This virtual workcell is exactly same as that of the real environment. This graphic simulation system of the multi-joint manipulator can be effectively used for designing the main processes and maintenance processes of the spent fuel management.