• 한국운동역학회지
• /
• 제15권1호
• /
• pp.29-44
• /
• 2005

The purpose of this study is to reveal the effects of two different kicks, the drop kick and the punt kick, into the kicking motion, through the kinetic comparative analysis of the kicking motion, which is conducted when one kicks a soccer goal. To grasp kinetic changing factors, which is performed by individual's each body segment, I connected kicking motions, which were analyzed by a two dimension co-ordination, into the personal computer to concrete the digits of it and smoothed by 10Hz. Using the smoothed data, I found a needed kinematical data by inputting an analytical program into the computer. The result of comparative analysis of two kicking motions can be summarized as below. 1. There was not a big difference between the time of the loading phase and the time of the swing phase, which can affect the exact impact and the angle of balls aviation direction. 2. The two kicks were not affected the timing and the velocity of the kicking leg's segment. 3. In the goal kick motion, the maximum velocity timing of the kicking leg's lower segment showed the following orders: the thigh(-0.06sec), the lower leg(-0.05sec), the foot(-0.018sec) in the drop kick, and the thigh(-0.06sec), the lower leg(-0.05sec), the foot(-0.015sec) in the punt kick. It showed that whipping motion increases the velocity of the foot at the time of impact. 4. At the time of impact, there was not a significant difference in the supporting leg's knee and ankle. When one does the punt kick, the subject spreads out his hip joint more at the time of impact. 5. When the impact performed, kicking leg's every segment was similar. Because the height of the ball is higher in the punt kick than in the drop kick, the subject has to stretch the knees more when he kicks a ball, so there is a significant affect on the angle and the distance of the ball's flying. 6. When one performs the drop kick, the stride is 0.02m shorter than the punt kick, and the ratio of height of the drop kick is 0.05 smaller than the punt kick. This difference greatly affects the center of the ball, the supporting leg's location, and the location of the center of gravity with the center of the ball at the time of impact. 7. Right before the moment of the impact, the center of gravity was located from the center of the ball, the height of the drop kick was 0.67m ratio of height was 0.37, and the height of the punt kick was 0.65m ratio of height was 0.36. The drop kick was located more to the back 0.21m ratio of height was 0.12, the punt kick was located more to the back 0.28m ratio of height was 0.16. 8. There was not a significant difference in the absolute angle of incidence and the maximum distance, but the absolute velocity of incidence showed a significant difference. This difference is caused from that whether players have the time to perform of not; the drop kick is used when the players have time to perform, and punt kick is used when the players launch a shifting attack. 9. The surface reaction force of the supporting leg had some relation with the approaching angle. Vertical reaction force (Fz) showed some differences in the two movements(p<0.05). The maximum force of the right and left surface reaction force (Fx) didn't have much differences (p<0.05), but it showed the tendency that the maximum force occurs before the peak force of the front and back surface (Fy) occurs.

• 대한기계학회논문집A
• /
• 제34권10호
• /
• pp.1367-1375
• /
• 2010

본 연구에서는 핫스템핑 소재로 사용되는 보론합금강판 22MnB5의 단일 겹치기 점용접에서 용접부의 강도 향상을 위한 최적화를 수행하였다. 최적화 과정은 다구찌 실험계획법에 의해 행해졌으며 공정변수는 전류, 가압력 및 통전시간으로 선정하였고, 잡음인자로서 핫스템핑 시 소재의 가열온도와 유지시간을 고려하였다. 가열조건에 따라 22MnB5 표면의 알루미늄 도금층과 모재 간의 확산반응에 의해 화합물층 두께에 산포가 발생하였으며 이러한 산포는 너겟의 형성에 영향을 미치는 것을 알 수 있었다. 한편 용접부의 인장전단강도를 목적함수로 하였을 때, 이러한 가열조건에 강건한 최적의 용접 조건은 전류 8kA, 가압력 4kN, 통전시간 18cycle로 선정되었다. 최적 조건의 검증 결과 용접부의 인장전단강도 는 32kN으로서 요구되는 규격인 23kN보다 크게 증가되었다.

• 한국운동역학회지
• /
• 제21권4호
• /
• pp.437-447
• /
• 2011

In this study, the lower limbs joints were analyzed for features based on the biomechanical characteristics of landing techniques according to height and landing on the ground type (flats and downhill). In order to achieve the objectives of the study, changes were analyzed in detail contents such as the height and form of the first landing on the ground at different angles of joints, torso and legs, torso and legs of the difference in the range of angular motion of the joint, the maximum angular difference between joints, the lower limbs joints difference between the maximum moment and the difference between COM changes. The subjects in this study do not last six months did not experience joint injuries 10 males in 20 aged were tested. Experimental tools to analyze were the recording and video equipment. Samsung's SCH-650A model camera was used six units, and the 2 GRF-based AMTI were used BP400800 model. 6-unit-camera synchronized with LED (photo cell) and Line Lock system were used. the output from the camera and the ground reaction force based on the data to synchronize A/D Syc. box was used. To calculate the coordinates of three-dimensional space, $1m{\times}3m{\times}2m$ (X, Y, Z axis) to the size of the control points attached to the framework of 36 markers were used, and 29 where the body was taken by attaching a marker to the surface. Two kinds of land condition, 40cm and 60cm in height, and ground conditions in the form of two kinds of flat and downhill slopes ($10^{\circ}$) of the landing operation was performed and each subject's 3 mean two-way RM ANOVA in SPSS 18.0 was used and this time, all the significant level was set at a=.05. Consequently, analyzing the landing technique as land form and land on the ground, the changes of external environmental factors, and the lower limbs joints' function in the evaluation were significantly different from the slopes. Landing of the slop plane were more load on the joints than landing of plane. Especially, knee extensor moment compared to the two kinds of landing, slopes plane were approximately two times higher than flat plane, and it was statistical significance. Most of all not so much range of motion and angular velocity of the shock to reduce stress was important. In the further research, front landing as well as various direction of motion of kinetic, kinetic factors and EMG variables on lower limbs joints of the study in terms of injury-prevention-approach is going to be needed.

• 한국산학기술학회논문지
• /
• 제10권12호
• /
• pp.3833-3838
• /
• 2009

본 논문은 산업용 로봇을 이용하여 운동화의 특성을 측정하는 측정장비를 소개한다. 여기서 사용된 로봇은 6관절의 퓨마타입 로봇(삼성전자의 FARA AT2 모델)을 인간의 보행 동작을 구현할 수 있도록 보완하였다. 보행 동작은 고속카메라로 분석한 후, 로봇 관절각들을 추출하여 동작구현에 사용한다. 3가지 종류의 경도 아웃솔(신발 겉창)로 만들어진 신발 시편을 준비하고, 이 로봇 시스템을 이용하여 걸음동작을 구현하여 신발에 따른 지면 충격력을 측정한다. 걸음동작에서 발생하는 발 앞축 부분을 굽히기 위해 요구되는 굽힘 모멘트의 측정과 걸음동작에서 발생하는 요동현상의 측정에 사용한다. 동일한 압축변형을 유지하도록 시스템을 설정하고, 신발을 측정한 결과 아웃솔의 경도에 따라 지면반력의 크기는 선형적으로 증가하는 추세가 관찰되었다. 또한 굽힘 모멘트와 요동현상 역시 아웃솔의 경도에 따라 선형적으로 증가하는 추세가 관찰되었다. 상기의 몇 가지 실험을 통하여, 본 로봇 시스템은 일관성 있는 실험결과를 제공하였으며, 따라서 산업용 로봇을 이용하여 신발의 유용한 특성 정보 도출이 가능하며, 추후 신발설계의 활용에 대한 가능성을 보여준다.

• 한국운동역학회지
• /
• 제16권1호
• /
• pp.101-108
• /
• 2006

The purpose of this study was to compare GRF characteristics during walking wearing jogging and roller shoes. Twelve male middle school students (age: $15.0{\pm}0.0\;yrs$, height: $173.6{\pm}5.0\;cm$, weight: $587.6{\pm}89.3\;N$) who have no known musculoskeletal disorders were recruited as the subjects. Kinematic data from six S-VHS camcorders(Panasonic AG456, 60 fields/s) and GRF data from two force platform; (AMII OR6-5) were collected while subjects walked wearing roller and jogging shoes in random order at a speed of 1.1 m/s. An event sync unit with a bright LED light was used to synchronize the video and GRF recordings. GRF data were filtered using a 20 Hz low pass Butterworth. digital filter and further normalized to the subject's body weight. For each trial being analyzed, five critical instants and four phases were identified from the recording. Temporal parameters, GRFs, displacement of center of pressure (DCP), and loading and decay rates were determined for each trial. For each dependent variable, paired t-test was performed to test if significant difference existed between shoe conditions (p <.05). Vertical GRFs at heel contact increased and braking forces at the end of initial double limb stance reduced significantly when going from jogging shoe to roller shoe condition. Robbins and Waked (1997) reported that balance and vertical GRF are closely related It seems that the ankle and knee joints are locked in an awkward fashion at the heel contact to compensate for the imbalance. The DCP in the antero-posterior direction for the roller shoe condition was significantly less than the corresponding value for the jogging shoe condition. Because the subjects tried to keep their upper body weight in front of the hip to prevent falling backward, the DCP for the roller shoe condition was restricted The results indicate that walking with roller shoes had little effect on temporal parameters, and loading and decay rates. It seems that there are differences in GRF characteristics between roller shoe and jogging shoe conditions. The differences in GRF pattern may be caused primarily by the altered position of ankle, knee, and center of mass throughout the walking cycle. Future studies should examine muscle activation patterns and joint kinematics during walking with roller shoes.

• 한국운동역학회지
• /
• 제19권4호
• /
• pp.627-636
• /
• 2009

본 연구는 한국무용 시 내면의 아름다움뿐만 아니라, 외면으로 표현되고 기술적으로 한층 세분화된 한국무용의 호흡에 대한 중요성을 인식하는 연구의 필요성을 갖고, 호흡의 사용이 한국무용 걸음체 동작에 어떠한 영향을 미치는 가를 분석하여, 무용의 추상적인 아름다움을 과학적인 근거로 명확하게 제공하는 데 연구의 목적을 갖는다. 연구 결과, 호흡을 사용한 걸음체가 호흡을 사용하지 않는 걸음체 보다 신체중심과 골반이 이동변위가 낮게 나타났다. 슬관절과 족관절의 각변위에서 호흡을 사용하는 걸음체가 호흡을 사용하지 않는 걸음체보다 굴곡되어 굽힘이 많이 사용되었고, 이것은 굴신이 일어나고 있는 시전에서 나타났다. 호흡을 사용한 걸음체 동작은 수직지면반력에서 호흡을 사용하지 않은 걸음체에서 볼 수 없는 pre정점이 나타났고 이것은 한국무용 걸음체 시 호흡이 시작되는 들숨의 시점을 의미하며, 뒤꿈치 닿는 구간(1정점)에서 호흡을 사용한 걸음체의 부하 값이 날숨에 의해 호흡을 사용하지 않는 걸음체 보다 부하 값이 더 크게 나타났다. 전후지면반력 결과 호흡을 사용한 걸음체가 제동력이 더욱 크게 나타났다.

• 한국운동역학회지
• /
• 제24권1호
• /
• pp.1-9
• /
• 2014

The purpose of this study was to investigate the muscle mechanical properties of the pelvic axial pre-rotational movement for the Jireugi in the Taekwondo Juchumseogi stance. Eleven elite Taekwondo Poomsae athletes participated. Each participant performed 5 right hand Jireugi in Juchumseogi stance as fast and strong as possible while their motion was recorded by a 3D motion analysis system and the ground reaction forces by two force plates. The power and work of the muscular group surrounding the waist were analyzed to verify the effect of the stretch-shortening cycle (SSC) theory. The cause of the greater power seems to be the application of the SSC by the muscles surrounding the waist during the preparation phase of the pre-rotation group. For the none pre-rotation group, they only used the concentric contraction of the muscles surrounding the waist. Because the pre-rotation group used the SSC theory, they had the effect of shortening of the range of movement, creating a fast and more powerful rotation, thus anticipating the increase the magnitude of impact.

• 한국정밀공학회지
• /
• 제18권5호
• /
• pp.137-146
• /
• 2001

A robust controller with the sliding mode is proposed for stable dynamic walking of the biped robot in this paper. For the robot system to be controlled, which is modeled as 14 DOF rigid bodies by the method of multi-body dynamics, the joint angle trajectories are determined by the velocity transformation matrix. Also Hertz force model and Hysteresis damping element are utilized for the ground reaction and impact forces during the contact with the ground. The biped robot system becomes unstable since those forces contain highly confused noise components and some discontinuity, and modeling uncertainties such as parameter inaccuracies. The sliding mode control is applied to solve above problems. Under the assumption of the bounded estimation errors on the unknown parameters, the proposed controller provides a successful way to achieve the stability and good performance in spite of the presence of modeling imprecisions of uncertainties.

• Biomaterials and Biomechanics in Bioengineering
• /
• 제3권2호
• /
• pp.71-84
• /
• 2016

The finite element method is wide used in simulation in the biomechanical structures, but a lack of studies concerning finite element mesh quality in biomechanics is a reality. The present study intends to analyze the importance of the mesh quality in the finite element model results from humeral structure. A sensitivity analysis of finite element models (FEM) is presented for the humeral bone and cartilage structures. The geometry of bone and cartilage was acquired from CT scan and geometry reconstructed. The study includes 54 models from same bone geometry, with different mesh densities, constructed with tetrahedral linear elements. A finite element simulation representing the glenohumeral-joint reaction force applied on the humerus during $90^{\circ}$ abduction, with external load as the critical condition. Results from the finite element models suggest a mesh with 1.5 mm, 0.8 mm and 0.6 mm as suitable mesh sizes for cortical bone, trabecular bone and humeral cartilage, respectively. Relatively to the higher minimum principal strains are located at the proximal humerus diaphysis, and its highest value is found at the trabecular bone neck. The present study indicates the minimum mesh size in the finite element analyses in humeral structure. The cortical and trabecular bone, as well as cartilage, may not be correctly represented by meshes of the same size. The strain results presented the critical regions during the $90^{\circ}$ abduction.

• 한국운동역학회지
• /
• 제26권2호
• /
• pp.161-166
• /
• 2016

Objective: The purpose of this study was to determine the knee and ankle joint kinematics and kinetics by comparing downhill walking with valley-shape combined slope walking. Method: Eighteen healthy men participated in this study. A three-dimensional motion capture system equipped with eight infrared cameras and a synchronized force plate, which was embedded in the sloped walkway, was used. Obtained kinematic and kinetic parameters were compared using paired two-tailed Student's t-tests at a significance level of 0.05. Results: The knee flexion angle after the mid-stance phase, the mean peak knee flexion angle in the early swing phase, and the ankle mean peak dorsiflexion angle were greater during downhill walking compared with valley-shape combined slope walking (p < 0.001). Both the mean peak vertical ground reaction force (GRF) in the early stance phase and late stance phase during downhill walking were smaller than those values during valley-shape combined slope walking. (p = 0.007 and p < 0.001, respectively). The mean peak anterior GRF, appearing right after toe-off during downhill walking, was also smaller than that of valley-shape combined slope walking (p = 0.002). The mean peak knee extension moment and ankle plantar flexion moment in late stance phase during downhill walking were significantly smaller than those of valley-shape combined slope walking (p = 0.002 and p = 0.015, respectively). Conclusion: These results suggest that gait strategy was modified during valley-shape combined slope walking when compared with continuous downhill walking in order to gain the propulsion for lifting the body up the incline for foot clearance.