• Structural Engineering and Mechanics
• /
• v.15 no.1
• /
• pp.151-157
• /
• 2003

A new approach to the analysis of horizontally curved beams is presented in this paper. The proposed method simplifies a two-dimensional structure into a one-dimensional structure just like a normal beam for structural analysis and, therefore, reduces the computational effort significantly.

• The Magazine of the Society of Air-Conditioning and Refrigerating Engineers of Korea
• /
• v.10 no.3
• /
• pp.220-227
• /
• 1981

The purpose of this paper is to investigate the potential ability of sintered metal tube to promote heat transfer. In the experiment for Freon - 11, the boiling heat transfer on the sintered metal tube of bronze element is investigated and compared with that of the bronze tube (bare tube) atmospheric pressure. The experimental results are obtained as follows : 1) For sintered metal tubes of bronze element with particle diameters which ranges from $79({\mu})\;to\;461({\mu})$ and bare tube, boiling characteristic curves are expressed as : a) Sintered metal tube $$q{\propto}{\Delta}T^{1.05\~1.373}$$ b) Brae tube $$q{\propto}{\Delta}T^{3.096}$$ 2) Compared with that of the bare tube at low temperature difference$({\Delta}T_{sat})$, boiling heat transfer coefficient of the sintered bronze tube are relatively high. 3) There is tendency that curves of boiling heat transfer coefficients of sintered ·bronze tube and bare tube approach each other at rather high temperature difference. It is due to the increasing rate of the former heat transfer coefficient along with temperature difference is smaller than that of the latter. 4) Referring to particle diameter, optimum condition, i. e. , maximum heat transfer coefficient is found to be at approximately 2 mm thickness of sintered layer with $D_p=150({\mu})$.

• Proceedings of the KIEE Conference
• /
• 2002.11c
• /
• pp.163-168
• /
• 2002

The voting algorithm for action selection performs self-improvement by Reinforcement learning algorithm in the dynamic environment. The proposed voting algorithm improves the navigation of the robot by adapting the eligibility of the behaviors and determining the Command Set Generator (CGS). The Navigator that using a proposed voting algorithm corresponds to the CGS for giving the weight values and taking the reward values. It is necessary to decide which Command Set control the mobile robot at given time and to select among the candidate actions. The Command Set was learnt online by means as Q-learning. Action Selector compares Q-values of Navigator with Heterogeneous behaviors. Finally, real-world experimentation was carried out. Results show the good performance for the selection on command set as well as the convergence of Q-value.

• Geomechanics and Engineering
• /
• v.8 no.1
• /
• pp.97-111
• /
• 2015

The kinematical approach of limit analysis is used to estimate the three dimensional stability analysis of rock slopes with nonlinear Hoek-Brown criterion under earthquake forces. The generalized tangential technique is introduced, which makes limit analysis apply to rock slope problem possible. This technique formulates the three dimensional stability problem as a classical nonlinear programming problem. A nonlinear programming algorithm is coded to search for the least upper bound solution. To prove the validity of the present approach, static stability factors are compared with the previous solutions, using a linear failure criterion. Three dimensional seismic and static stability factors are calculated for rock slopes. Numerical results of indicate that the factors increase with the ratio of slope width and height, and are presented for practical use in rock engineering.

• Structural Engineering and Mechanics
• /
• v.23 no.1
• /
• pp.97-113
• /
• 2006

A simply supported hybrid plate consisting of top and bottom functionally graded elastic layers and an intermediate actuating or sensing homogeneous piezoelectric layer is investigated by an elasticity (piezoelasticity) method, which is based on state space formulations. The general spring layer model is adopted to consider the effect of bonding adhesives between the piezoelectric layer and the two functionally graded ones. The two functionally graded layers are inhomogeneous along the thickness direction, which are approached by laminate models. The effect of interlaminar bonding imperfections on the static bending and free vibration of the smart plate is discussed in the numerical examples.

• Journal of Microbiology and Biotechnology
• /
• v.16 no.12
• /
• pp.1882-1889
• /
• 2006

A 16S rDNA clone library was generated to investigate the bacterial diversity in intertidal sediment from the coast of the Yellow Sea, P. R. China. A total of 102 clones were sequenced and grouped into 73 OTUs using a phylogenetic approach. The sequenced clones fell into 11 bacterial lineages: Proteobacteria, Bacteroidetes, Planctomycetes, Chloroflexi, Acidobacteria, Actinobacteria, Firmicutes, Spirochaetes, and candidate divisions of BRCl, OP3, and OP1l. Based on a phylogenetic analysis of these bacteria, together with the ten most closely related sequences deposited in the GenBank, it was concluded that intertidal bacteria are most likely derived from marine bacteria with a remarkable diversity, and some are particularly abundant in intertidal sediment.

• Structural Engineering and Mechanics
• /
• v.11 no.4
• /
• pp.357-372
• /
• 2001

In this paper, cantilevered tall structures are treated as cantilever bars with varying cross-section for the analysis of their free longitudinal (or axial) vibrations. Using appropriate transformations, exact analytical solutions to determine the longitudinal natural frequencies and mode shapes for a one step non-uniform bar are derived by selecting suitable expressions, such as exponential functions, for the distributions of mass and axial stiffness. The frequency equation of a multi-step bar is established using the approach that combines the transfer matrix procedure or the recurrence formula and the closed-form solutions of one step bars, leading to a single frequency equation for any number of steps. The Ritz method is also applied to determine the natural frequencies and mode shapes in the vertical direction for cantilevered tall structures with variably distributed stiffness and mass. The formulae proposed in this paper are simple and convenient for engineering applications. Numerical example shows that the fundamental longitudinal natural frequency and mode shape of a 27-storey building determined by the proposed methods are in good agreement with the corresponding measured data. It is also shown that the selected expressions are suitable for describing the distributions of axial stiffness and mass of typical tall buildings.

• Structural Engineering and Mechanics
• /
• v.46 no.4
• /
• pp.459-486
• /
• 2013

A novel damage classification method based on wavelet packet transform and statistical analysis is developed in this study for structural health monitoring. The response signal of a structure under an impact load is normalized and then decomposed into wavelet packet components. Energies of these wavelet packet components are then calculated to obtain the energy distribution. Statistical similarity comparison based on an F-test is used to classify the structure from changes in the wavelet packet energy distribution. A statistical indicator is developed to describe the damage extent of the structure. This approach is applied to the test results from simply supported reinforced concrete beams in the laboratory. Cases with single and two damages are created from static loading, and accelerations of the structure from under impact loads are analyzed. Results show that the method can be used with no reference baseline measurement and model for the damage monitoring and assessment of the structure with alarms at a specified significance level.

• Nuclear Engineering and Technology
• /
• v.56 no.5
• /
• pp.1863-1873
• /
• 2024

In the Korean domestic nuclear industry, to analyze the reliability of instrumentation and control (I&C) systems, the failure rates of the electronic components constituting the I&C systems are predicted based on the MIL-HDBK-217F standard titled 'Reliability Prediction of Electronic Equipment'. Based on these predicted failure rates, the mean time to failure of the I&C systems is calculated to determine the replacement period of the I&C systems. However, this conventional approach to the prediction of electronic component failure rates assumes that factors affecting the failure rates such as ambient temperature and operating voltage are static constants. In this regard, the objective of this study is to propose a prediction method for the remaining useful life (RUL) of electronic components considering mean time to failure calculations reflecting dynamic environments, such as changes in ambient temperature and operating voltage. Results of this study show that the RUL of electronic components can be estimated depending on time-varying temperature and electrical stress, implying that the RUL of electronic components can be predicted under dynamic stress conditions.

• Safety and Health at Work
• /
• v.14 no.4
• /
• pp.476-482
• /
• 2023

Introduction: There is a growing global interest in the issue of precarious employment. We aimed to analyze the characteristics and socio-demographic distribution of precarious employment using a summative score approach. Methods: To operationalize precarious employment, we utilized data from the Korean Working Conditions Survey and focused on three distinct dimensions: employment insecurity, income inadequacy, and a lack of rights and protections. By constructing a summative scale ranging from -16 to 2, with lower scores indicating higher precariousness, we measured employment precariousness among Korean wage workers. To compare employment precariousness according to survey participant characteristics, we employed the Wilcoxon Rank Sum Test. Results: We analyzed a weighted number of 38,432 workers. The overall sample showed a median (Q1, Q3) summative scale score of -3 (-6, -1). The median summative score was lower for women compared to men (men: -2; women: -5; p < 0.001), as well as for young or older workers compared to middle-aged workers (young: -4; middle-aged: -2; older: -5; p < 0.001). Similarly, workers with lower educational levels (middle school or below: -8; high school: -5; college or above: -2; p < 0.001) and non-white collar workers (blue collar: -5; service/sales worker: -6; white collar: -2; p < 0.001) experienced higher levels of employment precariousness. Conclusion: Our findings indicate that certain vulnerable groups, such as women, young or older adults, workers with low educational attainment, and caregiving or low-skilled elementary workers, are disproportionately exposed to high employment precariousness. Active policy interventions are needed to improve the employment quality of vulnerable groups.