• Proceedings of the KIEE Conference
• /
• 2001.07e
• /
• pp.40-42
• /
• 2001

본 논문은 Substrate의 온도를 200[$^{\circ}C$]로 유지하며 진공 저항 가열 증착법을 이용하여 ITO/Si 태양전지를 제작한 후 그 전기적 특성을 조사하였다. 전지의 단락전류와 개방전압의 열처리 온도의존성은 약450[$^{\circ}C$]이상부터 증가하여 650[$^{\circ}C$]부근에서 최대치를 나타내었다. 단락전류와 열처리 시간과의 관계에서는 증착시간이 15분 정도에서 최대치를 나타내었다. 일정한 태양에너지 조도 하에서 $SnO_2$의 성분비율을 높여감에 따라 전지의 개방전압과 단락전류는 다소 감소한 후 일정한 값으로 안정되는 경향을 나타내었다.

• Transactions on Electrical and Electronic Materials
• /
• v.17 no.1
• /
• pp.33-36
• /
• 2016

In the present work, a Ni-doped indium zinc oxide (NIZO) film and its multilayers with Ag layers were investigated as transparent conducting electrodes for liquid crystal display (LCD) applications, as a substitute for indium tin oxide (ITO) electrodes. By interposing the Ag layer between the NIZO layers, the loss of the optical transmittance occurred; however, the Ag layer brought enhancement of electrical sheet resistance to the NIZO/Ag/NIZO multilayer electrode. The twisted nematic cell based on the NIZO/Ag/NIZO multilayer electrode exhibited superior electro-optical characteristics than those based on single NIZO electrode and was competitive compared to those based on the conventional ITO electrode. An LCD-based NIZO/Ag/NIZO multilayer electrode may allow new approaches to conventional ITO electrodes in display technology.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2005.07a
• /
• pp.535-536
• /
• 2005

Organic photovoltaic effects were studied in a device structure of ITO/CuPc/Al and ITO/CuPc/$C_{60}$/BCP/Al. A thickness of CuPc layer was varied from 10 nm to 50 nm, we have obtained that the optimum CuPc layer thickness is around 40 nm from the analysis of the current density-voltage characteristics in CuPc single layer photovoltaic cell. From the thickness-dependent photovoltaic effects in CuPc/$C_{60}$ heterojunction devices, higher power conversion efficiency was obtained in ITO/20nm CuPc/40nm $C_{60}$/Al, which has a thickness ratio (CuPc:$C_{60}$) of 1:2 rather than 1:1 or 1:3. Light intensity on the device was measured by calibrated Si-photodiode and radiometer/photometer of International Light Inc(IL14004).

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2010.06a
• /
• pp.208-208
• /
• 2010

Indium zinc tin oxide (IZTO) thin films were studied as a possible alternative to indium tin oxide (ITO) films for providing low-cost transparent conducting oxide (TCO) for thin film photovoltaic devices. IZTO films were deposited onto glass substrates at room temperature. A dc/rf magnetron co-sputtering system equipped with a ceramic target of the same composition was used to deposit TCO films. Earlier studies showed that the resistivity value of $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20) films could be lowered to approximately $6{\times}10^{-4}ohm{\cdot}cm$ without sacrificing optical transparency and still maintaining amorphous structure through the optimization of process variables. The growth rate was kept at about 8 nm/min while the oxygen-to-argon pressure ratio varied from 0% to 7.5%. As-deposited films were always amorphous and showed strong oxygen pressure dependence of electrical resistivity and electron concentration values. Influence of forming gas anneal (FGA) at medium temperatures was also studied and proven effective in improving electrical properties. In this study, the chemical composition of the targets and the films varied around the $In_{0.6}Zn_{0.2}Sn_{0.2}O_{1.5}$ (IZTO20). It was the main objective of this paper to investigate how off-stoichiometry affected TCO characteristics including electrical resistivity and optical transmission. In addition to the composition effect, we have also studied how film properties changed with processing variables. IZTO thin films have shown their potential as a possible alternative to ITO thin films, in such way that they could be adopted in some applications where currently ITO and IZO thin films are being used. Our experimental results are compared to those obtained for commercial ITO thin films from solar cell application view point.

• 한국신재생에너지학회:학술대회논문집
• /
• 2010.06a
• /
• pp.69.1-69.1
• /
• 2010

We have fabricated organic photovoltaic cells (OPVs) with highly conductive poly 3,4-ethylenedioxythiophene : poly styrenesulfonate (PEDOT:PSS) layer as an anode without using transparent conducting oxide (TCO), which has been modified by adding some organic solvents like sorbitol (So), dimethyl sulfoxide (DMSO), N-methyl-pyrrolidone (NMP), dimethylformamide (DMF), and ethylene glycol (EG). The conductivity of PEDOT:PSS film modified with each additive was enhanced by three orders of magnitude. According to atomic force microscopy (AFM) study, conductivity enhancement might be related to better connections between the conducting PEDOT chains. TCO-free solar cells with modified PEDOT:PSS layer and the active layer composed of poly(3-hexylthiophene) (P3HT) and phenyl [6,6] C61 butyric acid methyl ester (PCBM) exhibited a comparable device performance to indium tin oxide (ITO) based organic solar cells. The power conversion efficiency (PCE) of the organic solar cells incorporating DMSO, So + DMSO and EG modified PEDOT:PSS layer reached 3.51, 3.64 and 3.77%, respectively, under illumination of AM 1.5 (100mW/$cm^2$).

• Proceedings of the Korean Institute of IIIuminating and Electrical Installation Engineers Conference
• /
• 2009.10a
• /
• pp.177-179
• /
• 2009

In order to investigate the possible application of ZnO films as a transparent conducting oxide (TCO) electrode, ZnO:Al films were prepared by RF magnetron sputtering method. The effects of surface treatment and doping concentration on the structural and electrical properties of ZnO films were mainly studied experimentally. Five-inch PDP cells using either a ZnO:Al or indium tin oxide (ITO) electrode were also fabricated separately under the same manufacturing conditions. The luminous properties of both the transparent conducting oxide electrode were measured and compared with each other. By doping the ZnO target with 2 wt% of Al2O3, the film deposited at a chemical surface treatment resulted in the minimum resistivity of 8.5 _ 10_4 U-cm and a transmittance of 91.7%. And DBD surface treatment resulted in the minimum resistivity of 8.5 _ 10_4 U-cm and a transmittance of 91.7%. Although the luminance and luminous efficiency of the transparent conducting oxide electrode using ZnO:AI are lower than those of the cell with the ITO electrode by about 10%, these values are sufficient enough to be considered for the normal operation of TCO.

• Proceedings of the Korean Vacuum Society Conference
• /
• 2011.08a
• /
• pp.231-231
• /
• 2011

본 연구에서는 co-sputtering 시스템을 이용하여 아나타세 TiO2의 도핑 농도 변화에 따른 다성분계 TiO2-ITO (TITO) 박막의 전기적, 광학적, 구조적 특성 변화 및 급속 열처리(RTA) 공정에 따른 전기적, 광학적 특성 변화를 분석하였다. 실험을 위해 아나타세 TiO2 타겟과 ITO 타겟(10 wt% $SnO_2$ doped $In_2O_3$)이 tilted cathode에 장착되었으며, ITO 타겟의 인가전류를 120 W로 고정한 채 아나타세 TiO2 타겟의 인가전류를 증가시킴으로써 도핑 농도를 변화하였다. 제작된 TITO 투명 전극의 전기적, 광학적, 구조적 특성 평가를 위해 four-point probe measurement, Hall effect measurement, UV/Vis. spectrometry, scanning electron microscopy (SEM) 이용하여 각각의 특성을 분석하였다. 상온에서 제작된 TITO의 경우 최적화된 $TiO_2$ 인가전류 100W에서 460.8 ohm/sq. 의 전기적 특성과 가시광선 영역 400~550 nm에서 85% 이상의 광학적 투과율을 확보할 수 있었다. 뿐만 아니라 상온에서 최적화된 TITO 투명 전극의 급속 열처리 시 600$^{\circ}C$ 급속 열처리 조건에서 매우 낮은 25.94 ohm/sq.면저항, $5.1{\times}10^{-4}$ ohm-cm 비저항과 81% 투과율을 확보할 수 있었다. 아나타세 $TiO_2$가 도핑된 TITO 투명 전극의 급속 열처리 공정에도 불구하고 매우 평탄한 표면을 나타냄을 SEM 이미지를 통하여 확인할 수 있었다. 이러한 TITO 투명 전극의 우수한 전기적, 광학적, 구조적 특성은 indium saving 투명 전극으로써 고가 ITO 박막의 대치가능성을 나타낸다.

• Solar Energy
• /
• v.12 no.2
• /
• pp.62-78
• /
• 1992

The solar cells of $ITO_{(n)}/Si_{(p)}$, which are ITO thin films deposited and heated on Si wafer 190[$^{\circ}C$], were fabricated by two source vaccum deposition method, and their electrical properties were investigated. Its maximum output is obtained when the com- position of the thin film consist of indium oxide 91[mole %] and thin oxide 9[mole %]. The cell characteristics can be improved by annealing but are deteriorated at temperature above 600[$^{\circ}C$] for longer than 15[min]. Also, we investigated the spectral response with short circuit current of the cells and found that the increasing of the annealing caused the peak shifted to the long wavelength region. And by experiment of the X-ray diffraction, it is shown to grow the grains of the thin film with increasment of annealing temperature. The test results from the $ITO_{(n)}/Si_{(p)}$ solar cell are as follows. short circuit current : Isc= 31 $[mW/cm^2]$ open circuit voltage : Voc= 460[mV] fill factor : FF=0.71 conversion efficiency : ${\eta}$=11[%]. under the solar energy illumination of $100[mW/cm^2]$.

• Toxicological Research
• /
• v.21 no.2
• /
• pp.141-150
• /
• 2005

1,3-Dichloro-2-propanol (1,3-DCP) is known as chloride chemicals and causes severe hepatotoxic agent. The Ito cells and Kupffer's cells of the liver in the 5 old F344 Rats were exposed to 1,3-DCP gas chamber for 6 hours/ a day, 5 days/ a week, and 13 weeks, in the 0, 5, 20, 80 ppm, respectively. After then the body weights, liver weights, and relative liver weight to body weight were measured, and the hepatic tissues were prepared by the routine and Immunostain method, and observed by the LM, and EM. In the results, there were severe body weight decrease (p<0.05) in the 80 ppm of the male and female rats. The relative liver weights to the body weight were increased relate with exposed 1,3-DCP concentration (P<0.001). Inflammatory cells, infiltration was observed at the perivascular area in the 20 ppm exposed group, and bilirubin pigment infiltration, bile duct hyperplasia, inflammation hepatocytic necrosis, fibrosis were observed in the 80 ppm exposure group. In the 80 ppm exposure group, disarrangement of the endothelial cells, erythrocytes and hepatic cell fragment in the Disse space and numerous migration macrophages were observed in the necrotic area by EM observation. In the immunostained hepatic tissues positive stained ED1 cells were extremely increased (P<0.05) in central vein area, but ED2 was weakly positive immunostained in the 80 ppm exposed group. Immunostained desmin was observed in the Ito cell. It was no difference in the low and medium exposed group but it was typical increase in the necrotic area. In conclusion, These results suggest that NOAEL of 1,3-DCP may be 5 ppm in rats and the Immunostained of desmin, ED1 and ED2 positive cells activated in the inflammatory liver were related to the exposure volume and density. The increase of the Ito cells were related to the severe phagocytosis of the Kupffer's cells.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.30-37
• /
• 1989

The PIN type a-SiC:H/a-Si:H heterojunction solar cells were fabricated by using the rf glow discharge decomposition of $SiH_4$ mixed with $CH_4,B_2,H_6\;and\;PH_3.$ The efficiency of the solar cell of the $SnO_2/ITO$ was higher than that of ITO transparent oxide layer by 1.5%. The P layer was prepared with the thickness of $100{\AA}$ and $CH_4/SiH_4$ ration of 5. The I layer has been deposited on the P layer and it is not pure intrinsic but near N type. So $SiH_4$ mixed with $B_2H_6$ of 0.3ppm was used to change this N type nature to intrinsic having the thickness of 5000${\AA}$. And consecutively, the N layer was deposited with t ethickness of $400{\AA}$ using $SiH_4/PH_3$ mixtures. The solar cell demonstrated 0.94V of $V_{oc'}$ 14.6mA/cm of $J_{sc}$ and 58.2% of FF, resulting the efficiency of 8.0%. To minimize loss by the reflection of light, $MgF_2$ layer was coated on the lgass and the efficiency was improved by 0.5%. Therefore, the solar cell indicated overall efficiency of 8.5%.