• Journal of Power Electronics
• /
• v.14 no.6
• /
• pp.1272-1280
• /
• 2014

This paper presents solutions for fault detection and diagnosis of two-level, three phase voltage-source inverter (VSI) topologies with IGBT devices. The proposed solutions combine redundant standby VSI structures and contactors (or relays) to improve the fault-tolerant capabilities of power electronics in applications with safety requirements. The suitable combination of these elements gives the inverter the ability to maintain energy processing in the occurrence of several failure modes, including short-circuit in IGBT devices, thus extending its reliability and availability. A survey of previously developed fault-tolerant VSI structures and several aspects of failure modes, detection and isolation mechanisms within VSI is first discussed. Hardware solutions for the protection of power semiconductors with fault detection and diagnosis mechanisms are then proposed to provide conditions to isolate and replace damaged power devices (or branches) in real time. Experimental results from a prototype are included to validate the proposed solutions.

• International Journal of Internet, Broadcasting and Communication
• /
• v.7 no.2
• /
• pp.90-95
• /
• 2015

This paper describes IEC 61727 standard of Photovoltaic (PV) systems -Characteristics of the utility interface. IEC 61727 standard tests include utility compatibility and personnel safety and equipment protection of PV inverter performance functions. Especially utility compatibility part includes test items of 1) voltage, current and frequency, 2) normal voltage operating range, 3) flicker, 4) DC injection, 5) normal frequency operating range, 6) harmonics and 7) waveform distortion, 8) power factor of PV inverter. Also personnel safety and equipment protection part includes test items 1)loss of utility voltage, 2)over/under voltage and frequency, 3)Islanding protection, 4)response to utility recovery, 5)earthing, 6)short circuit protection, 7)Isolation and switching of PV inverter. In this paper, each item of IEC 61727 standard test is studied and analyzed and finally full tested by PV inverter performance function.

• Proceedings of the KIEE Conference
• /
• 2001.07c
• /
• pp.1829-1831
• /
• 2001

A novel multi-section power divider configuration is proposed to obtain wide-band frequency performance up to microwave frequency region. Design procedures for the proposed microwave broadband power divider are composed of a planar multi-section three-ports hybrid and a waveguide transformer design procedures. The multi-section power divider is based on design theory of the optimum quarter-wave transformer. Furthermore, in order to obtain the broadband isolation performance between the two adjacent output ports, the odd mode equivalent circuit should be matched by using the lossy element such as resistor. The derived design formula for calculating these odd mode matching elements is based on the singly terminated filter design theory. The waveguide transformer section is designed to suppress the propagation of the higher order modes such as waveguide modes due to employing the metallic electric wall. Simulation and experiment show excellent performance of multi section power divider.

• Journal of the Korean Institute of Telematics and Electronics
• /
• v.26 no.6
• /
• pp.124-130
• /
• 1989

For the higher density DRAM'S, innovations in fabrication process and circuit design which have led to dramatic density improvement are discussed from the desinger's perspective. A new dynamic RAM cell called Trench Epitaxial Transistor Cell(TETC) using trench technics and SEG have been developed for use in future megabit DRAMS. Storge electrode with $n^+$-polysilicon and $n^+$-source electrode are self-contacted in TETC. With keeping the storage capacitance large enough to prevent soft errors, the cell size reduced to 30% compare with existing BSE cell by utilizing the vertical capacitor made along the isolation region.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.32A no.1
• /
• pp.129-137
• /
• 1995

AlGaAs/GaAs HBTs have been fabricated using SABM (Self-Aligned Base Metal) process technique. The mesa type HBTs were fabricated through following steps: isolation implant, wet etching, metal lift-off, and airbridge interconnection process. The fabricated HBTs with 2umx10um size emitter showed a common emitter current gain of 10 at a collector current density of Jk=100kA/cm$^{2}$, a breakdown volgate BVCEO of 8V, and the ideality factors of base and collector junctions of 1.6 and 1.1, respectively. On-wafer S-Parameter measurement at 0.5~18GHz has been made for the characterization of the common emitter HBTx with a 2umx10um size emitter. The extrapolated current gain cut-off frequency of ft=30GHz and maximum oscillation frequency of fmax=23 GHz were obtained at a collector current density of Jc=70kA/cm$^{2}$. Small signal HBT equivalent circuit was extracted from the S-Parameter data.

• 한국초전도학회:학술대회논문집
• /
• v.10
• /
• pp.15-20
• /
• 2000

We demonstrated a single balanced mixer of the combination of high-T. superconductor (HTS) and III-V GaAs beam lead Schottky diodes operating in the mini-cryogenic chamber. The HTS hybrid mixer was designed with a center frequency of 27.5 GHz and a bandwidth of 1 GHz, and consisted of a rat-race coupler circuit with beam-lead diodes attached to its balanced ports. The HTS hybrid mixer with 1 GHz RF bandwidths exhibits a conversion loss of 6 dB. A LO-to-RF isolation was greater than 40 dB in the range of operating frequencies. Since the HTS/III-V hybrid mixer devices have lower noise and conversion loss, this technique provide us with new capabilities that can be effectively utilized in the field of local-point distribution service (LMDS) systems.

• Proceedings of the IEEK Conference
• /
• 2000.06e
• /
• pp.191-194
• /
• 2000

A 2.4 GHz single ended two stage low noise amplifier(LNA) is designed for Bluetooth application. The circuit was implemented in a standard digital 0.25 $\mu\textrm{m}$ CMOS process with one poly and five metal layers. At 2.4 GHz, the LNA dissipates 34.5 mW from a 2.5V power supply voltage and provides 24.6 dB power gain, 2.85 dB minimum noise figure, -66.3 dB reverse isolation, and an output 1-dB compression level of 8.5 dBm.

• Proceedings of the KIEE Conference
• /
• 1997.11a
• /
• pp.422-425
• /
• 1997

This paper describes a resonant fly-back converter for high-voltage de distribution system. The proposed converter operates to change high-voltage de into low-voltage de with isolation and large converting ratio. The converter has a thyristor switch with an LC resonant circuit for commutation in the primary side of the gap transformer. The operation of the proposed system was verified through computer simulations and hardware scaled-model tests. The proposed system can be implemented with commercially available components and proven technologies.

• Journal of Power Electronics
• /
• v.2 no.3
• /
• pp.155-161
• /
• 2002

This paper presents a maximum power point tracking algorithm for Photovoltaic array using only instantaneous output current information. The conventional Hill climbing method of peak power tracking has a disadvantage of oscillations about the maximum power point. To overcome this problem, we have developed an algorithm that will estimate the duty ratio corresponding to maximum power operation of solar cell. The estimation of the optimal duty ratio involves, finding the duty ratio at which integral value of output current is maximum. For the estimation, we have used the well know Lagrange's interpolation method. This method can track maximum power point quickly even for changing solar isolation and avoids oscillations after reaching the maximum power point.

• Journal of the Korean Institute of Telematics and Electronics A
• /
• v.31A no.6
• /
• pp.26-33
• /
• 1994

Much time and labor has been conventionally paid for fine adjustment of circuit elements by experience to improve the characteristics of Tap-off for CATV systems. To solve the problem, in this paper, the relations between the even- and odd-mode impedance. Z$_{oe}$ and Z$_{oo}$ of symmetrical 4-port coupled-line directional coupler and power dividing characteristics of Tap-off for CATV system have been derived. After the coupling, the reflectivity and the isolation are represented by Z$_{oe}$ and Z$_{oo}$ only, the fine adjustment of all S-parameters can be performed by controling the elements of Z$_{oe}$ and Z$_{oo}$ only. Furthermore, the validity of the new fine adjustment method proposed here has been confirmed by experiments.