• Journal of Korean Society of Occupational and Environmental Hygiene
• /
• v.23 no.2
• /
• pp.164-168
• /
• 2013

Objectives: This study was aimed at the examination of the lead exposure status of smelting process workers in steelmaking using scrap iron. Methods: The study was conducted from July to September 2012 by means of measurements taken during the smelting process, with 45 minutes set for a one-time smelting work cycle when it comes to personal air sample and area air sample. As such, daily work hours were classified into 360 minutes for measurement. The analysis of lead concentration was conducted using AAs based on the NIOSH 7300 method. Results: In the case of the personal specimens that were subjected to periodical measurement 45 minutes per one session during the smelting process, 40 out of 42 specimens measured were found to contain lead, with an average concentration level of $0.028mg/m^3$ (Max: $0.182mg/m^3$, Min: $0.005mg/m^3$, TWA-more than 50%: 4 out of 6 units). In the case of regional specimens, lead was detected in 45 out of 48 specimens measured, with an average concentration level of $0.037mg/m^3$ (Max: $0.220mg/m^3$, Min: $0.007mg/m^3$ ). In the case of regional specimens subjected to measurement using a day as the work cycle, lead was detected in 15 out of 15 specimens measured, with an average concentration level of $0.049mg/m^3$ (Max: $0.478mg/m^3$, Min: $0.005mg/m^3$ ). Conclusions: It concluded that smelting process workers in steelmaking are exposed to lead because scrap iron is used as a raw material. It is thus necessary to introduce legal management to prevent occupation-related disease in smelting process workers in steelmaking.

• Journal of the Korean Chemical Society
• /
• v.25 no.3
• /
• pp.183-189
• /
• 1981

Iron and titanium, the major constituents in iron ores, were X-ray spectrometrically determined by using the dilution parameter method. A standard and samples possessing a similar composition were diluted with the diluent $ZrO_2$ to their proper respective ratios. After measuring the intensity of the fluorescent X-ray, the dilution parameter was calculated from the following equation. $Pa=\frac{\frac{I_{as}}{(I_{as})_d}}{D-1}{^{-1}}$The dilution parameters were used to correct the difference between the matrix effect of the standard and that of the sample. The content of the major constituents was calculated, without using any standard calibration curves, from the following equation;$W_a=W_a^*{\cdot}{\frac{I_as}{I_{as}^*}{\cdot}\frac{P_a^*}{P_a}$where asterisks indicate the standard. The results agreed with those of the wet analysis within 2% of relative error, and the precision of the experiment was also tolerably good.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.19 no.3
• /
• pp.248-262
• /
• 1990

General purpose of the study was to understend nutritional status of the Korean farmers and thus provide rural nutrition intervention programs with more useful in formation and data. The data for the study was collected two times from the 603 sample farm households in 1982 and 1987. The main results of the study were as follows ; 1) Food intake of the Korean farmers was highly dependent upon vegetable foods especially on cereals and gains. However the unbalanced food intake pattern was gradually improved as consumption of vegetable foods was decreased from 992.8 grams per person per day in 1982 to 946.4g in 1987 and that of animal foods increased from 54.2g to 91.4g . 2) In mean value analysis on nutrient intake of the farmeres intakes of energy and protein were nearly reached to Recommended Dietary Allowances(RDA) level; intakes of calcium vitamin A and riboflavin were quite deficient whereas iron thiamin niacin and ascorbic acid were well over. From 1982 to 1987 intakes of all nutrients except energy were increased. 3) In distribution analysis on nutrient intake coefficient of variation(CV) of all nutrients except iron was increased. skewness(SK) the coefficients of calcium iron vitamin A riboflavin and ascorbic acid were decreased Kurtosis (Ku) of iron and vitamin A was increased. On the whole distributions of nutrient intake of the farmers were changed in undesirable ways although the mean values of the nutrient intake were improved 4) In relationship analysis among 115 relationships 76 relationships were consistent between 1982 and 1987. Of 76 consistent relationships only 10 relationship were significant at 5% level such as the protein intake level and the balance of food intake calcium intake level and the age etc.

• Journal of Nutrition and Health
• /
• v.7 no.3
• /
• pp.27-44
• /
• 1974

A general survey of 82 perschool children and 473 school children (from 1st to 3rd grade) residing in the Dongnae area of Shindong Myun, choonseoung Gun, Kangwon Province was conducted from June 12 to 21, 1973, to obtain information concerning nutritional status, especially the protein and iron nutrition of preschool and school children in a rural area of Korea. A sample of 58 children 2 to 9 years old was selected from these 555 children for hematological, biochemical and parasitological tests. The results of these tests are presented below, 1) Both the mean body height and mean body weight of these children were higher and heavier than the averages in the Korean Physical Standards. About 39 per cent were above the 90 th percentile of the Korean Physical Standards of height and 35 per cent were above the 90th percentile of the Korean Physical Standards of weight. 2) The rate of infestation by helminthes was 67.6 per cent and there were no cases of hookworm infestation Among the ascaris-infected children, 61.6 per cent fell within an Ascaris E.P.G. count range of $501{\sim}2,000$. This was considered a rather mild intensify of ascaris infection. Nutrient loss due to helminthes was also estimated to be low. 3) The mean hemoglobin level was 11.3gm% $({\pm}0.94)$, and 68.4 per cent of the children were anemic (less than 11gm% among those 5 years old or less, less than l2gm% among those 6 years old or more). The average hematocrit value was 36.1% $({\pm}2.36)$, and only 3.5 per cent showed more than 34% on the M.C.H.C. test. These results showed that the incidence of anemia, in these rural children was high, and that in general it displayed hypochromic characteristics. 4) The average serum iron level was $78.2{\mu}g%$\;({\pm}29.8). The Proportion of the children showing less than $50{\mu}g% in the serum iron level was 5.6 per cent, while 41.8 percent revealed $450{\mu}g% or more in the TIBC determination. Transferrin saturation was below 15% in 71.4 percent of the preschool children, and in 28.6 percent of the school children. Those who had a serum iron level of $50{\mu}g% or less and a TIBC of more than $450{\mu}g% constituted 11.9 percent of the children examined. From these results, it was concluded that especially preschool children were low in iron nutrition, and that most of the anemia might be iron-deficiency anemia. 5) The mean values of total serum protein and albumin were 6.98gm% and 4.99gm% respectively. Especially in serum albumin, all children stowed more than 4 gm%. 6) The mean urinary urea nitrogen Per creatinine ratio was 11.5 $({\pm}4.2)$, and 21.8 percent had a ratio of more than 15. Considering these results, it was suggested that protein nutrition in these children was relatively good.

• Journal of Conservation Science
• /
• v.25 no.4
• /
• pp.399-409
• /
• 2009

Outdoor iron artefacts are easily corroded by affection of environmental pollutants directly. Especially they need to be removed $Cl^-$ ions, but outdoor iron artefacts are excluded for desalination owing to their special features. Therefore this study contains the conservation processes of an iron stele of the Joseon Dynasty as the sample as well as desalination experiments that were carried out the desalting method using spill pads and the immersion desalting method together in order to compare. Desalting methods were compared by analyses such as an optical and metallurgical microscope, SEM-EDS, pH meter, Ion Chromatography and X-ray diffraction. As a result of the analysis, the optical and metallurgical microscopy show that the corrosion products are constituted by the layers and the metallurgical microstructure is a white cast iron. The SEM-EDS results of corrosion products detected mainly Fe, O, and especially Cl upto 2.48wt%. The results of pH and anion analysis for the washing solution, the desalting method using spill pads shows the similar effect to the immersion desalting method. As a result of XRD analysis before and after desalting corrosion products, goethite, magnetite, lepidocrocite and akaganeite are detected before desalting, but akaganeite is not detected after desalting at the desalting methode using spill pads, which indicates to have an effect on desalination. Therefore the results show that the desalting method using spill pads has an effect on desalination similar to the immersing desalting method.

• Journal of Conservation Science
• /
• v.35 no.6
• /
• pp.631-640
• /
• 2019

The purpose of this study was to compare analytical results of sand iron bars reproduced by the traditional iron-making method through a destructive analysis and a non-destructive analysis. For these studies, we produced two types of samples. One was sample(SI-A), a part of the sand iron bar for destructive analysis. The other was SI-B(9 ㎠) for non-destructive analysis. A metallurgical microscope and scanning electron microscope were used for the destructive analysis, and neutron imaging analysis with the Hokkaido University Neutron Source (HUNS) at Hokkaido University, Japan, was used for the non-destructive analysis. The results obtained by destructive analysis showed that there was ferrite and pearlite of fine crystallite size, and some of these showed Widmanstätten ferrite microstructure grown within the pearlite and coarse ferrite at the edge of the specimen. The results from the neutron imaging analysis showed that there was also ferrite and pearlite with 3 ㎛ α-Fe of BCC structure. Based on these results, neutron imaging analysis is capable of identifying material characteristics without destroying the object and obtaining optimal research results when applying it to objects of cultural heritage.

• Journal of Korean Society of Forest Science
• /
• v.3 no.1
• /
• pp.18-22
• /
• 1963

1. Objects The experiments of catalytic aharcoaling were carried out for the fallowing purposes. (1) To determine the economically desirable amount of catalytic materials to be used when a catalytic charcoaling is practiced. (2) To observe the rate of carbonization of non-treated charcoal wood when the catalytic charcoaling is proceeded in the same charcoal pit. 2. Meterials (1) Small sample chips made of oak (Q. accutissima Carr.), measured by 0.5cm in width and thickness, respectively, and 1cm in length, were used as charcoal wood in each experiment. (2) Ammonium chloride was used as a catalytic material and electric kiln as a charcoaling apparatus. 3. Experiment (1) The sample chips were put into a electric oven for three hours at the temperature $60^{\circ}{\sim}70^{\circ}C$ in order to reduce some water contents. (2) Oven dried sample chips were then soaked for an hour in solution of ammonium chloride. Three kinds of solution were prepared, that is, 2.5%, 5%, and 10%, solution in which the amount of ammonium chloride used was weighed at the rate of 0.5%, 1.0%, and 2.0% to the total weight of the sample chips, resppectivelly. (3) Soaked sample chips were put in the air for 12 hours to reduce some water contents, and then were put into electric oven for 2 hours at the temperature $105^{\circ}{\sim}110^{\circ}C$. (4) Dried sample chips were kept in a desiccator with control sample chips which were treated excarly the same process as the treated sample chips except only not using the ammonium chloride in the process of soking. (5) Sample chips kept in the desiccator were used at random in each charcoaling experiment. (6) Charcoaling in the electric kiln were carried out by using small crucibles with complete cover to reduce the amount of ash. At each charcoaling experiment four crucibles filled with sample ships, weighed about 20gr, were put into electric kiln. The charcoaling was continued for an hour at the temperature $400^{\circ}{\sim}450^{\circ}C$. (7) In order to investigate the influence given by the gases produced during the catalytic charcoaling to the rate of carbonization of non-treated sample chips, the following experiment was done. (a) A crueible was divided into two parts by inserting a fine iron net at the middle of the crucible, and then non-treated sample chips, weighed about 10gr, were put in the upper part of the crucible and treated sample chips, weighed also about 10gr, were put in the under part. (b) The crucibles filled with two kinds of sample chips were put into a electric kiln for an hour at the temperature $400^{\circ}{\sim}450^{\circ}C$. 4. Results. Results for two replications (with four crucibles in one replication) for each experiment designed are as follows : (1) The rats of carbonization of the non treated sample chips, and that of the treated sample chips with ammonium chloride at the rate of 1.5%, 1.0%, and 2.0% to the total weight of the sample chips used were averaged at 19.85%, 22.63%, 24.14%, and 26.60%, respectively. (2) The rats of carbonization of the non-treated sample chips were averaged at (a) 20.04% (0.5% treatment), (b) 20.28% (1.0% treatment), and (c) 20.61% (2.0% treatment) when the treated sample chips were carbonized in the same crucible.

• Proceedings of the Korea Institute of Applied Superconductivity and Cryogenics Conference
• /
• 2003.10a
• /
• pp.3-6
• /
• 2003

In this work the AC loss measurement setup based on an iron core background magnet, not used in a conventional one, has been successfully developed, To prove its validity, a round-robin test for the same Bi-2223 tape sample among three institutes has been done. The results show that test data from the developed setup well agree with losses measured at different institutes.

• Journal of Nutrition and Health
• /
• v.7 no.3
• /
• pp.1-13
• /
• 1974

The relative state of human iron storage may be ascertained more reliably through determination of the serum iron, iron binding capacity, transferrin saturation and absorption of radioactive iron in conjunction with studies of red cell morphology than from the study of red cell morphology alone. Recent investigations have shown that there is an increase in red cell protoporphyrin concentration in iron deficiency anemia. The significance of the red cell protoporphyrin has been discussed greatly during the years since its discovery. Two of the main factors which appear to influence the amaunt of protoporphyrin are increased erythropoiesis and factors interfering with the utilization of iron in the synthesis of hemoglobin, and iron deficiency. Recently Heller et al. have described a simplified method for blood protoporphyrin assay and this technique could be used assess nutritional iron status, wherein even minor insufficiencies are detectable as increased protoporphyrin concentrations. Based on the evaluation of the relationship between nutritional iron status and red cell protoporphyrin as an index suitable for the detection of the iron deficiency is described in this paper. RESULTS 1. Hemoglobin Concentrations and Anthropometric Measurements. The mean and standard deviations of the various anthropometric measurements of different age and sex groups are shown in table 1. There measurements have been compared with the Korean Standard. In the absence of local standards for arm circumference and skin-fold thickness over triceps, they have been compared with the standard from Jelliffe. Table 2,3, and 4 give anthropometric measurements and frequency (%) of anemia in children surveyed. The mean height of the children studid was 10 to 20 percent; below the Korean Standard. The distribution of height below 80 percent of the Standard was 21.2 percent, however, among anemic group this percentage was 27.7 percent. In general, the mean weight of the children was 10 to 15 percent below the Korean Standard. The percentage of children with weight less than 80 percent of the Standard was about 35 percent. But in the anemic group of the children, this percentage was 44 percent. The mean arm circumference was about 15 percent lower than the Jelliffe's standard. 61.2 percent of the children had values of arm circumference below 80 percent of the standard. Children with low hemoglobin levels, this percentage was 80 percent. The mean skinfold thickness over the triceps of the children studied was about 25 Percent lower than the Jelliffe's standard and 61.2 percent of the children had the value less than 80 percent of the standard. Among anemic children, this percentage was 70.8%. As may be seen from table 5, the mean hemoglobin concentration of the total group was 11.3g/100ml. Hemoglobin concentration was less than 11.0g/100ml. in 65(36.5%) of the 178 children. The degree of anemia in most of these children was mild with a hemoglobin level of less than 8.0g/100ml. found in only one child. In general, the prevalence of anemia was high in female children than male and decreased its frequency with increasing age. Relatively close relationship was observed between hemoglobin level and anthrophometric measurements especially high between arm circumference and skinfold thickness and hemoglobin but very low in height and low in weight and hemoglobin level, estimated by chi-square value. II. Serum iron, Transferrin saturation (1) Serum iron, and transferrin saturation Serum iron, transferrin saturation and red cell protoporphyrin concentrations were estimated in sub-sample of 84 children from 1 to 6 years and 24 older children between 7 and 13 years of age. The findings are presented in table 6. The mean serum iron concentration of the total group was 59ug/100ml. However, the level incrased with age from 36.6ug/100ml. (1-3years) to 80.8ug/100ml. (7-13 years). 60 percent of these children had a serum iron level less than 50ug/10ml. in the 1-3 years age group and 31.4 percent for 4-6 years group. These contrast with the finding of 12.5 percent anemic children in the 7-13 years age group. The mean transferrin saturation for the total group was 18.1 percent and frequency of anemia by transferrin saturation was observed same pattern as serum iron concentration. (2) Red cell protoporphyrin concentrations. (a) Red cell protoporphrin levels of children: Red cell protoporphyrin and other biochemical data are shown in table 4. The mean concentration in red cell of all children was fround 46.3ug/100ml. RBC. and differences with age groups were observed; in the age group 1-3 years, the mean concentration was $59.5{\pm}32.14$ ug/100ml. RBC; 4-6 years $44.1{\pm}22.57$ ug/100ml. RBC. and 7-13 years, $39.0{\pm}13.56$ ug/100ml. RBC. (b) Normal protoporphyrin values in adults: It was observed that in 10 normal adult males studied here the level of protoporphyrin in red cell ranged from 18 to 54 ug/100ml. RBC. and the mean concentration was $47.5{\sim}14.47$ ug/100ml. RBC. Other biochemical determination made on the same subjects are presented in table 8. (c) Red tell protoporphyrin concentration of occupational blood donors: The results of analyses for red cell protoporphyrin as well as serum iron, transferrin saturation and hemoglobin in the 76 blood donors are presented in table 7 and 8. In this experiment, donors were selected at random, however, most of them bled repeatedly because of poor economic situation, I doubt. Table 9 shows the distribution of red cell protoporphyrin concentration and hemoglobin concentration of occupational donors. The mean hemoglobin value for the total was 11.9 g/100 ml. When iron deficiency anemia is defined as a transferrin saturation below 15%, prevalence of anemia was 47.4 percent and the mean serum iron was 27.1ug/100ml. and red cell protoporphyrin, 168.3ug/100ml. RBC. However, mean serum iron and protoporphyrin concentration of above 15% transferrin saturation were 11.6 ug/100 ml. and 58.8 ug/100 ml. RBC. respectively. The mean Protoporphyrin concentration of non-anemic (above 15% transferrin saturation) donors was slightly higher than the results of normal adult males.

• Journal of environmental and Sanitary engineering
• /
• v.19 no.1
• /
• pp.42-49
• /
• 2004

The study was carried out in order to improve the quality of fermented soybean, that is, Doenjang with strain ,mold and bactea, added mulberry leaves powder were investigated and analyzed as follows. 1. The water content of samples was 38.51-50.10%, pH value 5.44-6.21 and total acidity, 2.42-3.13 2. The reducing sugar of content for samples was 7.01-7.24% on contrast mulberry added sample was 8.34-12.11%, Amino-N as contrast 5.96-7.63% mulberry added, 8.34-12.11% 3. In sensory evaluation test, excellent results was 2% added sample than others. 4. The heaby metals analyzed form samples cans, iron, tin and lead content of samples were 5.63-6.03 ppm, 31.70-35.53 ppm and trace.