• Journal of the Korean Society for Heat Treatment
• /
• v.25 no.6
• /
• pp.279-282
• /
• 2012

$SnO_2$ thin films were prepared on the Si substrate by radio frequency (RF) magnetron sputtering and then surface of the films were irradiated with intense Ar ion beam to investigate the effect of Ar ion irradiation on the properties and hydrogen gas sensitivity of the films. From atomic force microscope observation, it is supposed that intense Ar bombardments promote rough surface and increase gas sensitivity of $SnO_2$ films for hydrogen gas. The films that Ar ion beam irradiated at 6 keV show the higher sensitivity than the films were irradiated at 3 keV and 9 keV. These results suggest that the $SnO_2$ thin films irradiated with optimized Ar ion beam are promising for practical high-performance hydrogen gas sensors.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 1996.11a
• /
• pp.357-360
• /
• 1996

MgO protection layer in ac PDP(plasma display panel) prevents the dielectric layer from ion bombarding in discharge plasma. The MgO layer also has the additional important role in lowering the firing voltage due to a large secondary electron emission coefficient. Until now, the MgO protection layer is mainly prepared by E-beam evaporation. In this study, MgO protection layer is prepared on dielectric layer of ac PDP cell by reactive R.F magnetron sputtering with Mg target under various conditions of oxygen partial pressure. Discharge characteristics of PDP is also studied as a parameter of MgO preparation conditions. The sputtered MgO shows the better discharge characteristics compared with MgO deposited by E-beam evaporator.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.307-310
• /
• 2000

Antimony doped tin oxide (ATO) thin films were deposited at room temperature by ion-beam sputter deposition (IBSD) technique in oxidizing atmosphere utilizing Sb and Sn metal targets. Effect of Sb doping concentration, film thickness and heat treatment on electrical and optical properties was investigated. The thickness of as-deposited films was controlled approximately to $1500{\AA}$ or $2000{\AA}$, and Sb concentration to 10.8 and 14.9 wt%, as determined by SEM and XPS analyses. Heat treatment was performed at the temperature from $400^{\circ}C$ to $600^{\circ}C$ in flowing $O_2$ or forming gas. The resulting ATO films showed widely changing electrical resistivity and optical transmittance values in the visible spectrum depending on the composition, thickness and firing condition.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2008.11a
• /
• pp.301-301
• /
• 2008

Ion beam (IB)-induced alignment of inorganic materials has been investigated intensively as it provides controllability in a nonstop process for producing high-resolution displays[1][2]. LC orientation via ion-beam (IB) irradiation on the nitrogen doped diamond like carbon (NDLC) thin film deposited by physical deposition method-sputtering was embodied. The NDLC thin film that was deposited by sputter showed uniform LC alignment at the 1200eV of the ion beam intensity. The pretilt angle of LC on NDLC thin films was measured with various IB exposure time and angle. The maximum pretilt angle were showed with IB irradiation angle of $45^{\circ}$ and exposure time of 62.5 sec, respectively. To show NDLC thin film stability in high temperature, thermal stability test was proceeded. The uppermost of the thermal stability of NDLC thin film was $200^{\circ}C$. In this investigation, the electro-optical (EO) characteristics of LC on NDLC thin film were measured.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.110-110
• /
• 1999

Polyvinylidenefluoride (PVDF) is most used in piezoelectric polymer industry. Electrode effect on the electrical properties of PVDF has been investigated. al has been used due to fair adhesion for PVDF. Work function of metal plays an important role on the electrical properties of ferroelectrics for top and /or bottom electrode. However, Al has much lower work function than Pt or Au and so leakage current of Al/PVDF/Al may be large. Pt or Au has not been used for electrode of PVDF system due to poor adhesion. PVDF irradiated by Ar+ ion beam with O2 environment takes good adhesion to inert metal. Contact angle of PVDF to triple distilled water was reduced from 75$^{\circ}$ to 31$^{\circ}$ at 1$\times$1015 Ar+/cm2. Working pressure was 2.3$\times$10-4 Torr and base pressure was 5$\times$10-6 Torr. Pt was deposited by ion beam sputtering and thickness of pt film was about 1000$\AA$. in previous study, enhancing adhesion of Pt on PVDF was shown. in this study, effect of electrode on PVDF will be represented.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1999.07a
• /
• pp.154-154
• /
• 1999

금속산화막은 전자부품 및 광학적 응용에 널리 사용되고 있다. 특히 알루미늄의 산화막은 유전체의 재료로 커패시터에 많이 사용되고 있다. 이러한 알루미늄 산화막을 plasma를 이용한 ion plating에 의해 형성하였다.Activated Reactive Evaporation은 화합물의 증착율을 높이는데 좋은 증착법이다. 이러한 증착법에는 reactive ion plating와 ion-assisted deposition 그리고 ion beam sputtering 등이 있다. 본 연구에서는 알루미늄 산화막을 증착시키기 위해 plasma를 이용한 electron-beam법을 사용하였다. Turbo molecular pump로 챔버 내의 진공을 약 10-7torr까지 낸린 후 5$\times$10-5torr까지 O2와 Ar을 주입시켰다. 각 기체의 분압은 RGA(residual gas analyzer)로 조사하여 일정하게 유지시켰다. plasma를 발생시키기 위해 filament에서 열전자를 방출시키고 1kV 정도의 electrode에 의해 가속시켜 이들 기체들과 반응시켜 plasma를 발생시켰다. 금속 알루미늄을 5kV정도의 고전압과 90mA의 전류로 electron beam에 의해 증발시켰다. 기판의 흡착율을 높ㅇ기 위해 기판에 500V로 bias 전압을 걸어 주었다. 증발된 금속 알루미늄 증기들이 plasmaso의 산소 이온들과 활성 반응을 이루어 알루미늄 기판 위에 Al2O3막을 형성하였다. 알루미늄 산화막을 분석하기 위해 XPS(X-ray Photoelectron Spectroscopy)로 화학적 조성을 조사하였는데, 알루미늄의 2p전자의 binding energy가 76.5eV로 측정되었다. 이는 대부분 증착된 알루미늄이 산소 이온과 반응하여 Al2O3로 형성된 것이다. SEM(Scanning electron Microscopy)과 AFM(Atomim Force microscopy)으로 증착박 표면의 topology와 roughness를 관찰하였다. grain의 크기는 10nm에서 150nm이었고 증착막의 roughness는 4.2nm이었다. 그리고 이 산화막에 전극을 형성하여 유전 상수와 손실률 등을 측정하였다. 이와 같이 plasma를 이용한 3-beam에 의한 증착은 금속의 산화막을 얻는데 유용한 기술로 광학 재료 및 유전 재료의 개발 및 연구에 많이 사용될 것으로 기대된다.

• Proceedings of the Korean Institute of Electrical and Electronic Material Engineers Conference
• /
• 2000.05b
• /
• pp.142-145
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface glow discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with the dc bias voltage of -10V showed lower discharge voltage and lower erosion rate by ion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process.

• Proceedings of the Korean Vacuum Society Conference
• /
• 1998.02a
• /
• pp.41-41
• /
• 1998

Rare earth metal films have been used as a buffer layer for growing ferroelectric t thin film or a seed layer for magnetic multilayer. But when it was deposited on s semiconductor substrates for the application of magneto-optic (MO) storage media, it i is difficult to exactly measure magnetic cons떠nts due to shunting current, and so it n needs to grow metal films on insulator substrate to reduce such effect. Recently, it w was reported that ultra-thin Pt layer were epitaxially grown on A12O:J by ion beam s sputtering in 비떠 high vacuum and it can be used as a seed layer for the growth of C Co-contained magnetic multilayer. In this stu$\phi$, Pt thin film were epi떠xially grown on AI2D3 ($\alpha$)OJ) by RF magnetron s sputtering. The crystalline structure was analyzed by transmission electron microscope ( (TEM) and Rutherford Back Scattering (RBS)/Ion Channeling. In TEM study, Pt was b believed to be twinned on AI잉3($\alpha$)01) su$\pi$ace about Pt(ll1) plane.Moreover, RBS c channeling spectra showed that minimum scattering yield of Pt(111)/AI2O:J(1$\alpha$)OJ) was 4 4% and Pt(11J)/AI2D3($\alpha$)OJ) had 3-fold symmetry.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.2032-2034
• /
• 2000

The performance of ac plasma display panels (PDP) is influenced strongly by the surface glow discharge characteristics on the MgO thin films. This paper deals with the surface slew discharge characteristics and some physical properties of MgO thin films prepared by reactive RF planar unbalanced magnetron sputtering in connection with ac PDP. The samples prepared with the do bias voltage of -10V showed lower discharge voltage and lower erosion rate by ion bombardment than those samples prepared by conventional magnetron sputtering or E-beam evaporation. The main factor that improves the discharge characteristics by bias voltage is considered to be due to the morphology changes or crystal structure of the MgO thin film by ion bombardment during deposition process.

• Nuclear Engineering and Technology
• /
• v.55 no.9
• /
• pp.3121-3125
• /
• 2023

Neutron conversion detectors that use ¹⁰B-enriched boron carbide are feasible alternatives to ³He-based detectors. We prepared boron carbide films at micron-scale thickness using direct-current magnetron sputtering. The structural characteristics of natural B₄C films, including density, roughness, crystallization, and purity, were analyzed using grazing incidence X-ray reflectivity, X-ray diffraction, X-ray photoelectron spectroscopy, time-of-flight secondary ion mass spectrometry, and scanning electron microscopy. A beam profile test was conducted to verify the practicality of the ¹⁰B-enriched B₄C neutron conversion layer. A clear profile indicated the high quality of the neutron conversion of the boron carbide layer.