• Korean Chemical Engineering Research
• /
• v.57 no.1
• /
• pp.65-72
• /
• 2019

In this study, heterogeneous ion exchange membranes were prepared by casting method with various mixing ratios of PPO ion-selective solution and ion exchange resin. Then heterogeneous bipolar membranes were prepared by using this. The water content of heterogeneous cation and anion exchange membranes were 60~80% respectively, the ion exchange capacity was 2.81~3.26 meq/g, 2.31~2.74 meq/g and electrical resistances were $1.65{\sim}1.45{\Omega}{\cdot}cm^2$ and $1.55{\sim}1.05{\Omega}{\cdot}cm^2$. The tensile strength of heterogeneous bipolar membrane was lower than that of PPO resin before functionalization ($700Kg_f/cm^2$). The tensile strength of heterogeneous bipolar membrane with catalyst layer was lower than that of non-catalytic heterogeneous bipolar membrane. The water splitting voltage of the heterogeneous bipolar membrane with catalyst layer was low and stable at a minimum of 1.7~1.8 V, maximum 3.9~4.0 V, and the water splitting voltage of the non-catalytic heterogeneous bipolar membrane was constant at 3.8~4.0 V.

• Journal of Korean Society of Water and Wastewater
• /
• v.35 no.6
• /
• pp.533-544
• /
• 2021

Ion exchange (IX) performance on the exchanger bed is essentially evaluated for the generation of ultrapure water in electronics and chemical industries and for the corrosion control in nuclear power plants. The breakthrough characteristics of IX bed with multi-component were investigated with both cation- and mixed-IX beds of H- and ETAH-form for four kinds of cation exchange resins by using the combined solution of ethanolamine (ETA) and ammonia (NH₃) at trace NaCl. Unlike major components (ETAH⁺ and NH₄⁺ ), the phenomena of breakthrough and overshooting at bed outlet were not observed by Na⁺ over the test period (> 3 times theoretical exchange capacity of IX bed). The breakthrough from H-form resin bed was sequentially reached by ETAH⁺ and NH₄⁺, while the overshooting was observed for ETAH⁺ at the breakthrough of NH₄⁺. NH₄⁺ was 51.5% higher than ETAH⁺ in terms of the relative selectivity determined with the width of breakthrough zone. At the increased concentration of Na⁺ at bed inlet, the selectivity and the overshooting were decreased and increased, respectively. Na⁺ leakage was higher from ETAH-form resin bed and was not identical for four kinds of cation-exchange resins, which may be reduced by improving the intrinsic property of IX resin.

• Nuclear Engineering and Technology
• /
• v.12 no.1
• /
• pp.29-38
• /
• 1980

A radiochemical separation scheme for the neutron activation analysis is developed for the determination of 28 elements in aluminum. The scheme is based on a group separation using ion-exchange resin and mineral exchanger. Present work has employed mineral acids and their partly organic mixture excluding HF as the media as well as common glass wares. For the determination, gamma-ray spectroscopy using $3"\times3"\;Nal(TI)$ detector and a single comparator method are used.

• Resources Recycling
• /
• v.17 no.4
• /
• pp.37-46
• /
• 2008

In view of the increasing importance of the waste recycling to meet the strict environmental regulations, the present investigation reports an adsorption process using cationic exchanger DOWEX G-26 for the recovery of copper from the synthetic sulphate solutions containing copper 0.3 to 0.5 mg/ml, similar to the CMP waste effluent of electronic industry. Various process parameters viz. contact time, solution pH, resin dose, and A/R ratio for elution were investigated to recover copper from the effluents. Complete adsorption of copper from the solution was achieved at equilibrium pH 2.5 and aqueous I resin (A/R) ratio of 100 ml/g in 14 minutes contact time. The adsorption of copper on DOWEX G-26 resin was found to follow the Langmuir isotherm and second order reaction. The copper was eluted from loaded resin with dilute sulphuric acid to produce copper-enriched solution.

• Journal of Korean Society of Environmental Engineers
• /
• v.31 no.9
• /
• pp.775-782
• /
• 2009

PP-g-AA-Am nonwoven fabric, which possess anionic exchangeable function, was prepared by chemical modification of carboxyl (-COOH) group of PP-g-AA nonwoven fabric to amine ($-NH_2$) group using diethylene triamine (DETA). Its adsorption characteristics for anionic nutrients including isotherm, kinetics and co-anions were studied by batch adsorption experiments. Adsorption equilibriums of $PO_4$-P on PP-g-AA-Am fabric were well described by the Langmuir isotherm model, and their adsorption energies were ranged 10.3 kJ/mol indicating an ion-exchange process as primary adsorption mechanism. The adsorption selectivity of PP-g-AA-Am nonwoven fabric for anions under competition with each other was in following order: $SO_4\;^{2-}$>$PO_4\;^{3-}$>$NO_3\;^-$>$NO_2\;^-$. Also, all results obtained from this study indicate that the $PO_4$-P removal capacity of PP-g-AA-Am nonwoven fabric was extremely superior to that of PA308 anion-exchange resin.

• Journal of the Korean Chemical Society
• /
• v.31 no.3
• /
• pp.231-235
• /
• 1987

In 10M chloride (4M HCl + 6M LiCl) solution, cobalt, but not nickel, formed complex anion (${CoCl_3}^-$), and this anion was extracted by a liquid anion exchanger with Amberlite LA-2. The ion exchange capacity was 2.175meq of cobalt complex per unit ml of Amberlite LA-2. Upon eluting the resin with 0.4M nitric acid, the cobalt complex was stripped and transfered into eluate quantitatively. By using this separation method in the chloride solution dissolved with 50mg of cobalt (II) and 500mg of nikel(II), recovery of cobalt were 99.6 percent.

• Biotechnology and Bioprocess Engineering:BBE
• /
• v.11 no.1
• /
• pp.61-66
• /
• 2006

The simple Langmuir isotherm is frequently employed to describe the equilibrium behavior of protein adsorption on a wide variety of adsorbents. The two adjustable parameters of the Langmuir isotherm - the saturation capacity, or $q_m$, and the dissociation constant, $K_d$ - are usually estimated by fitting the isotherm equation to the equilibrium data acquired from batch equilibration experiments. In this study, we have evaluated the possibility of estimating $q_m$ and $K_d$ for the adsorption of bovine serum albumin to a cation exchanger using batch kinetic data. A rate model predicated on the kinetic form of the Langmuir isotherm, with three adjustable parameters ($q_m,\;K_d$, and a rate constant), was fitted to a single kinetic profile. The value of $q_m$ determined as the result of this approach was quantitatively consistent with the $q_m$ value derived from the traditional batch equilibrium data. However, the $K_d$ value could not be retrieved from the kinetic profile, as the model fit proved insensitive to this parameter. Sensitivity analysis provided significant insight into the identifiability of the three model parameters.

• KSBB Journal
• /
• v.11 no.5
• /
• pp.606-612
• /
• 1996

A specific ammino auid in a mixture can be crystallized inside an ion exchange column when displacer concentration is high enough to concentrate the amino acid in a pure band beyond its solubility limit. Glutamic acid formpd a discrete crystal layer in a cation exchanger column by operating displacement development mode and using a high concentration of displacer NaOH. The glutamic acid crystal formed was eluded from the column with the effluent stream and collected in a fraction collector. When 1.0 M of NaOH was used as a displacer, more than 60% of the loaded glutamic acid was recovered as crystal. The continuous crystallization and dissolution of crystal occurred, resulting in apparent movement of the crystal along the column without clogging or pressure increase. NaOH was proved a better displacer than NaCl because hydroxide ions neutralized hydrogen ions released from the resin and thus reduced the number of hydrogen ion competing with sodium ion for re-adsorption. The displacement development process coupled with crystallization provided higher concentration and recovery of glutamic acrid than conventional chromatography.

• Journal of the Korean Society of Food Science and Nutrition
• /
• v.21 no.1
• /
• pp.76-83
• /
• 1992

Enterotoxigenic E. coli is one of the major causative agents of the infantile diarrhea and traveler's diarrhea. The heat-stable enterotoxin (ST) is thought to be a virulence factor in the pathogenesis of the diarrhea and to be a maker for identification of the enterotoxigenic E. coli from non pathogenic E. coli. ST producing E. coli KM-7 strain was isolated from the swine and molecular cloning of ST gene of KM-7 strain. Transformant eKT-53 $(ST^+,\;LT^-)$ was selected by infant mouse assay (IMA). The culture supernatant of eKT-53 strain was performed purification by multipled steps. The culture supernatant (crude ST) was purified by sequentially applying batch adsorption chromatography on Amberlite XAD-2 resin, ion exchange chromatography on DEAE-Sephacel anion exchanger, gel filtration chromatography on Bio-Gel P-6 and preparative polyacrylamide slab gel electrophoresis. About 113-fold purification was achieved with a yield of about 11% of crude ST and the minimum effective dose(MED) of this purified ST was about 2.8ng in IMA. Homogeneity of purified ST was demonstrated by showing a single band in analytical SDS polyacrylamide disc gel electrophoresis.