• 대한원격탐사학회:학술대회논문집
• /
• 대한원격탐사학회 2003년도 Proceedings of ACRS 2003 ISRS
• /
• pp.1246-1248
• /
• 2003

Internal wave with a soliton-like, large amplitudes within several kilometers, is frequently observed in the sea surface caused by tidal rectification due to sill or rough topographic changes. Internal waves can perturb current and density field, initiate bottom sediment re -suspension and mix nutrients to photic zone. Previous studies indicate that the appearance of internal wave in the Lombok Strait have been detected in SAR image data. This paper studies effect of internal wave in the Lombok Strait to chlorophyll distribution in the surrounded areas using SeaWiFS and ERS SAR images data during 1996-2001 periods. The preliminary result concludes that the internal waves presumably affect phytoplankton distribution spreading southeastward in the coast off Bali Island. The distribution of phytoplankton at southern coastline off Bali Island when internal wave occurred is elongated and distributed further to westward (from 8.8$^{\circ}$ to 10.7$^{\circ}$LS) than the area when internal wave did not occur on August 2000 (from 9.25$^{\circ}$ to 10.25$^{\circ}$LS) as shown in figure 3. It shown that the surface phytoplankton concentration near coastal area, i.e. from 8.8$^{\circ}$ to 9.25$^{\circ}$ LS, increased when internal wave is occurred.

• Journal of Biosystems Engineering
• /
• 제23권6호
• /
• pp.615-620
• /
• 1998

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. In recent, ultrasonic wave has been considered as a solution for this problem. It transmit well through most materials and can handle safely and easily. However, specially in a watermelon, it is known that general frequency band (higher than 20kHz) ultrasonic waves do not transmitted well due to severe attenuation. The objectives of this study were to find out the proper waveform and frequency of the ultrasonic waves that transmit well inside the watermelon, and to analyze the transmitted waveform in order to make clear the structure of wave propagation in watermelon. The result of several experiments showed that 2kHz shear wave was the most suitable for the detection of internal cavity in the watermelon. Also, it was found that the surface wave did not influence the directly transmitted bulk wave. These results could be a basis of application of ultrasonic wave on the evaluation of internal quality of the watermelon.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 학술대회 논문집 정보 및 제어부문
• /
• pp.273-275
• /
• 2005

Active thermography is being used since several years for remote non-destructive testing. It provides thermal images for remote detection and imaging of damages. Also, it is based on propagation and reflection of thermal waves which are launched from the surface into the inspected component by absorption of modulated radiation. For energy deposition, it use external heat sources (e.g., halogen lamp or convective heating) or internal heat generation (e.g., microwaves, eddy current, or elastic wave). Among the external heat sources, the ultrasound is generally used for energy deposition because of defect selective heating up. The heat source generating a thermal wave is provided by the defect itself due to the attenuation of amplitude modulated ultrasound. A defect causes locally enhanced losses and consequently selective heating up. Therefore amplitude modulation of the injected ultrasonic wave turns a defect into a thermal wave transmitter whose signal is detected at the surface by thermal infrared camera. This way ultrasound thermography(UT) allows for selective defect detection which enhances the probability of defect detection in the presence of complicated intact structures. In this paper the applicability of UT for fast defect detection is described. Examples are presented showing the detection of defects in PCB material. Measurements were performed on various kinds of typical defects in PCB materials (both Cu metal and non-metal epoxy). The obtained thermal image reveals area of defect in row of thick epoxy material and PCB.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2012년도 춘계학술대회 논문집
• /
• pp.833-834
• /
• 2012

• 한국정밀공학회지
• /
• 제20권3호
• /
• pp.82-88
• /
• 2003

The nondestructive internal quality evaluation of agricultural products has been strongly required from the needs for individual inspection. Recently, the ultrasonic wave has been considered as a solution fur this problem, and an ultrasonic system was constructed for the ultrasonic NDE of fruits and vegetables in our previous work. In this paper, the practical applicability of our ultrasonic system is tested fur the inspection of internal defects (central cavity) in Atlantic potato. Sound speed and RMS of transmitted ultrasonic wave signal were measured and classification algorithm using 2 dimensional stochastic analysis. was presented. Experimental results showed greater value of sound speed and RMS (root mean square) of transmitted signal in normal samples than in abnormal samples with cavity. Also a stochastic method to distinguish normal and abnormal showed fault detection rate less than 5%.

• 대한전기학회논문지:시스템및제어부문D
• /
• 제55권2호
• /
• pp.68-71
• /
• 2006

Active thermography has been used for several years in the field of remote non-destructive testing. It provides thermal images for remote detection and imaging of damages. Also, it is based on propagation and reflection of thermal waves which are launched from the surface into the inspected component by absorption of modulated radiation. For energy deposition, it use external heat sources (e.g., halogen lamp or convective heating) or internal heat generation (e.g., microwaves, eddy current, or elastic wave). Among the external heat sources, the ultrasound is generally used for energy deposition because of defect selective heating up. The heat source generating a thermal wave is provided by the defect itself due to the attenuation of amplitude modulated ultrasound. A defect causes locally enhanced losses and consequently selective heating up. Therefore amplitude modulation of the injected ultrasonic wave turns a defect into a thermal wave transmitter whose signal is detected at the surface by thermal infrared camera. This way ultrasound thermography(UT) allows for selective defect detection which enhances the probability of defect detection in the presence of complicated intact structures. In this paper the applicability of UT for fast defect detection is described. Examples are presented showing the detection of defects in PCB material. Measurements are performed on various kinds of typical defects in PCB materials (both Cu metal and non-metal epoxy). The obtained thermal image reveals area of defect in row of thick epoxy material and PCB.

• 한국해양학회지:바다
• /
• 제4권1호
• /
• pp.18-24
• /
• 1999

인공위성의 SAR 센서를 이용하여 1996년 8월 15일 획득한 영상 자료로부터 제주도 북쪽 연안에서 내부파가 관측되었다. 영상 자료와 내부파가 발생한 주변 수심 그리고 조석자료를 고려해 볼 때 이 내부파는 여름철의 성층화된 해수에서 조류 전류시 조류가 해저 지형과의 상호 작용에 의하여 발생한 것으로 추측되며 솔리톤의 형태를 띠고 있다. 영상자료에서 분석한 솔리톤의 파장과 K-dV 방정식을 이용하여 가능한 솔리톤의 진폭을 계산하였다. 이러한 내부파는 물리적으로, 군사적으로, 그리고 해양생물학적으로 매우 중요한 현상으로 앞으로 내부파의 시간 및 공간적인 변화를 알기 위하여 SAR 영상 관측과 동시 현장관측을 병행하는 더 많은 연구가 필요하다.

• 대한기계학회논문집A
• /
• 제23권11호
• /
• pp.1878-1885
• /
• 1999

Ultrasonic technique which is one of the most common nondestructive evaluation techniques has been applied to evaluate the integrity of structures by analyzing the characteristic of scattering sign al from internal defects. Therefore, a numerical analysis of ultrasonic scattering field due to defect profiles is absolutely needed for the accurate, quantitative estimation of internal defects. In this paper, the SH-wave scattering by multi-cavity defects and inclusion using Elastodynamic Boundary Element Method is studied. The effects of shape and distance of defects on transmitted and reflected fields are considered. The interaction of multi-cavity defects in SH-wave scattering is also investigated. Numerical calculations by the BEM have been carried out to predict near field solution of scattered fields of ultrasonic SH-wave. The presented results can be used to improve the detection sensitivity and pursue quantitative nondestructive evaluation for inverse problem.

• Journal of Welding and Joining
• /
• 제30권6호
• /
• pp.36-41
• /
• 2012

General condensers consist of many tubes supported by tube sheets and support plates to prevent the deflection of the condenser tubes. When a fluid at high pressure and temperature runs over the tubes for the purpose of transferring heat from one medium to another, the tubes vibrate and their surface comes into contact with the support plates. This vibration causes damage to the tubes, such as cracks and wear. We propose an ultrasonic guided wave technique to detect the above problems in the support plate region. In the proposed method, the ultrasonic guided wave mode, L(0,1), is excited using an internal transducer probe from a single position at the end of the tube. In this paper, we present a preliminary experimental verification using a super stainless tube and show that the defects can be discriminated from the support signals in the support region.

• 한국전산구조공학회:학술대회논문집
• /
• 한국전산구조공학회 1998년도 가을 학술발표회 논문집
• /
• pp.413-420
• /
• 1998

In this study, an expert system is developed to evaluate a safety of tunnel structures. Using a dynamic finite element analysis module, this expert system predicts dynamic responses of a concrete lining surface which a transient force is applied on and estimates the condition between the concrete lining and surrounding ground. The evaluation parameter values of the module are multi-reflected wave frequency and amplitude of the dynamic responses. The multi-reflected wave frequency represents the depth of concrete lining, and the other parameter, the amplitude of the frequency, is utilized for detecting the internal flaws. A comparison of the dynamic responses between numerical and experimental model test verifies an effectiveness of this system. By this expert system, the safety of tunnel structures and the detection of internal flaws of concrete linings are estimated quantitatively.