• 한국철도학회논문집
• /
• 제12권2호
• /
• pp.309-314
• /
• 2009

열차가 터널에 진입하면 열차의 전두부에 의해 압축파가, 후마부에 의해 팽창파가 터널 내에 각각 발생하게 된다. 터널내부에서 압축파와 팽창파가 열차와 서로 상호작용하면서 열차 실내/외의 양력은 급격하게 변화한다. 본 논문에서는 한국형 틸팅차량이 터널 주행 시 나타나는 차량의 실내 및 실외(차량표면) 압력변화 및 압력변화율을 분석하여, 터널길이와의 상관관계를 분석하였다. 또한, 현 틸팅차량의 기밀상태에서 터널주행 시 실내압력변화율을 검토하였다. 그 결과 길이가 짧은 터널에서는 압력파의 중첩이 발생하지 않아서 차량 실내/외 압력변화는 크게 나타나지 않았다. 하지만, 긴 터널에서는 압력파의 중첩과 차량과의 상호작용이 동시에 일어나면서 급격한 압력변화가 뚜렷하게 발생하였다. 또한, 특정한 길이의 터널에서는 압축파와 팽창파가 중첩되어 압력변화 및 변화율을 크게 완화시켰다.

• International Journal of Railway
• /
• 제1권4호
• /
• pp.169-174
• /
• 2008

Experimental study has been conducted to clarify the internal and external pressure variation characteristics for KTX(Korea Train eXpress) passing through tunnel. Abrupt pressure variation gives rise to the ear-discomfort for passenger and fatigue for car body. In this study, the internal and external pressure variation are measured by using KTX real train experiment and on-board portable data acquisition system in Gyeongbu high speed commercial line. The tunnels from 200 m to 4000 m in length are chosen for the investigation of tunnel length effects. From the results of experiment, the internal pressure variation rate for all the test tunnels is lower than the standard criteria of 200 Pa/s. And, the critical tunnel lengths for pressure wave pattern are classified into 7 groups by using the theoretical L-t diagram analysis.

• 한국철도학회:학술대회논문집
• /
• 한국철도학회 2008년도 춘계학술대회 논문집
• /
• pp.2114-2119
• /
• 2008

When a train enters into a tunnel, a compression wave is generated by a front nose and a expansion wave is generated by a rear nose each other. Because the compression wave and expansion wave have interactions with the train in a tunnel repeatedly, the internal pressure of the train is dramatically varied. And this pressure variation gives passengers discomfort like ear-ache. In this paper, we had measured the internal pressure variation of TTX developed and being on Test-Running in Honam line and made an analysis of pressure variation rate. As a result, the internal pressure variation was different as to the length of tunnel. Though the entering velocity of TTX is similar on test tunnels, on the short tunnel, the pressure drop was lower then that of the long tunnel. And it was expected that the rates of internal pressure variation would be exceeded the limits on 160km/h entering velocity.

• 한국결정성장학회지
• /
• 제13권6호
• /
• pp.304-308
• /
• 2003

분리기 내 압력 조절을 통하여 압력 변화가 세라믹 입자 $Al_2O_3$, $Fe_2O_3$ 분급에 미치는 영향을 수치 해석적으로 분석하였다. 입자 분급 해석을 위해 3차원 Lagrangian approach를 이용하였으며, 이를 통해 입자의 분리기 내 거동 경로를 추적하여 각 압력에 따른 분리 가능한 최소 입자 크기(cut-diameter)와 분리율(separation rate)를 계산하였다. 압력 감소는 입자를 운반하는 아르곤 가스의 밀도를 감소시키면서, 분리기 내부 압력 손실을 줄이는 원인이 되었다. 이로 인해 상압에서 분리기 압력이 저압 상태로 변함에 따라, 더 미세한(수 $\mu\textrm{m}$) 입자가 분리 가능함이 예측되었다. 특히 50 torr의 저압 하에서 계산된 세라믹 입자의 분급 양상을 분석하면,$Al_2O_3$ 입자는 4 $\mu\textrm{m}$, $Fe_2O_3$경우는 3$\mu\textrm{m}$ 크기의 입자 분리가 가능하였다.

• 반도체디스플레이기술학회지
• /
• 제22권4호
• /
• pp.19-25
• /
• 2023

With an attempt to investigate the correlation between the internal pressure distribution of slit nozzle and the thickness uniformity of slot-coated thin films, we have performed computational fluid dynamics (CFD) simulations of slit nozzles and slot coating of high-viscosity (4,800 cPs) polydimethylsiloxane (PDMS) using a gantry slot-die coater. We have calculated the coefficient of variation (CV) to quantify the pressure and velocity distributions inside the slit nozzle and the thickness non-uniformity of slot-coated PDMS films. The pressure distribution inside the cavity and the velocity distribution at the outlet are analyzed by varying the shim thickness and flow rate. We have shown that the cavity pressure uniformity and film thickness uniformity are enhanced by reducing the shim thickness. It is addressed that the CV value of the cavity pressure that can ensure the thickness non-uniformity of less than 5% is equal to and less than 1%, which is achievable with the shim thickness of 150 ㎛. It is also found that as the flow rate increases, the average cavity pressure is increased with the CV value of the pressure unchanged and the maximum coating speed is increased. As the shim thickness is reduced, however, the maximum coating speed and flow rate decrease. The highly uniform PDMS films shows the tensile strain as high as 180%, which can be used as a stretchable substrate.

• 드라이브 ㆍ 컨트롤
• /
• 제13권4호
• /
• pp.7-13
• /
• 2016

This paper presents the meter-out and meter-in speed control characteristics of a pneumatic cylinder with relief valve type cushion device. The piston displacement and velocity are measured to investigate high speed driving performance with variation of the pressure setting in relief valve, air supply pressure, load mass, the supply and exhaust flow rate from the cylinder. Also, the internal pressures and temperatures driving pressure and cushion chamber are measured. The piston displacements and velocities of meter-out and meter-in control are compared experimentally determined data. A comparison experimental data meter-out and meter-in control show that a relief valve type cushion device is suitable for high speed pneumatic cylinders. The desired response characteristics of piston displacement and velocity are satisfactory adjust the pressure setting of a relief valve with varying system parameters such as air supply pressure, load mass and controlled flow rate.

• 한국유체기계학회 논문집
• /
• 제13권6호
• /
• pp.51-56
• /
• 2010

A numerical simulation is carried out to investigate the effect of flow rate variation and performance characteristics of double-suction centrifugal pump. Two types of pump which have different impeller inlet breadth and curvature of the shroud line consist of six blades impeller and shroud ring. Finite-volume method with structured mesh and $k-\omega$ Shear Stress Transport turbulence model was used to guaranty more accurate prediction of turbulent flow in the pump impeller. Total head, power and overall efficiency were calculated to obtain performance characteristics of two types of pump according to the variation of flow rate. From the results, impeller having smooth curve along the shroud line obtained good performance. The lower flow rate, the more circulation region, flow unsteadiness and complicate flow pattern are observed. Complicated internal flow phenomena through impellers such as flow separation, pressure loss, flow unsteadiness and performance are investigated and discussed.

• 동력기계공학회지
• /
• 제12권3호
• /
• pp.12-18
• /
• 2008

In the present study, the numerical simulation has been performed to investigate K-factor for temperature variation of working fluid in spray nozzle with orifice. The commercial CFD software, Fluent with the proper modeling was applied for analyzing the internal of the spray nozzle. Numerical result for K-factor at $20^{\circ}C$ agrees with the experimental result that it applied n=0.5 within about 7% error. The pressure drop inside nozzle is showed 20% passing swirler, 70% in the region between the outlet of swirler and the orifice and 10% at the outlet of orifice. As the operating pressure is increased, K-factor is decreased by effect of flow resistance at it's inlet before pass swirler. The temperature increase of working fluid reduced the flow rate according to reducing of density, and average 1.23% decrease is showed in the present research.

• Geomechanics and Engineering
• /
• 제12권2호
• /
• pp.313-326
• /
• 2017

Based on the reliability theory and limit analysis method, the roof stability of a shallow tunnel is investigated under the condition of surface settlement. Nonlinear Hoek-Brown failure criterion is adopted in the present analysis. With the consideration of surface settlement, the internal energy and external work are calculated. Equating the rate of energy dissipation to the external rate of work, the expression of support pressure is derived. With the help of variational approach, a performance function is proposed to reliability analysis. Improved response surface method is used to calculate the Hasofer-Lind reliability index and the failure probability. In order to assess the validity of the present results, Monte-Carlo simulation is performed to examine the correctness. Sensitivity analysis is used to estimate the influence of different variables on reliability index. Among random variables, the unit weight significantly affects the reliability index. It is found that the greater coefficient of variation of variables lead to the higher failure probability. On the basis of the discussions, the reliability-based design is achieved to calculate the required tunnel support pressure under different situations when the target reliability index is obtained.

• 한국안전학회지
• /
• 제15권3호
• /
• pp.57-65
• /
• 2000

The stress corrosion crack growth is simulated assuming a small axial surface crack inside a S/G tube. Internal pressure and residual stresses are considered as applied forces. Stress intensity factors along crack front, variation of crack shape and crack growth rate are obtained and discussed. It is noted that the aspect ratio of the crack is not depend on the initial crack shape but depend on the residual stress distribution.