• Journal of environmental and Sanitary engineering
• /
• v.13 no.1
• /
• pp.91-103
• /
• 1998

Design data for COD and nitrogen removal from wastewater were collected from Pilot's Multi-stage Bio-reactor. Hyraulic conditions and pollutant loadings were varied in order to optimize the biological and operational parameters. Pilot's experimental results summarize as followings. 1. T-N removal efficiency in the organic volumetric loading 0.2 kgCOD/m$^{3}$·d was obtained as maxium of 85% at internal recycle ratio 2.5 and in more ratio than this it was decreased. Organic removal efficiency was about 91% under the overall experimental conditions and not influenced by recycle ratio.. 2. Nitrification reaction was shown as maxium in the SCOD$_{cr}$/NH$^{+}$-N ratio of 6.5 and in more ratio than this it was decreased. Denitrification rate was the maxium as 85% in more than 7.5 of SCOD$_{cr}$/NO$_{x}$-N ratio and in the ratio over this ratio it becomes constant. 3. By utilizing an applied new model of Stover-Kincannon from Monod's kinetic model, concentration of T-N in the effluent according to flow quanity in the influent was estimated as 8.74 and -67.5 respectively. The formula for estimating T-N concentration of effluent was obtained like this: N$_e$=N$_0$(1- $\frac{8.74}{(QN$_0$/A)-67.05}$)

• Archives of Pharmacal Research
• /
• v.23 no.4
• /
• pp.367-373
• /
• 2000

Cholic acid, conjugated with amine-terminated poly(W-isopropylacrylamide) (abbreviated as CA/ATPNIPAAm), was synthesized by a N, N'-dicyclohexyl carbodiimide (DCC)-mediated coupling reaction. Self-assembled CA/ATPNIPAAm micelles were prepared by a diafiltration method in aqueous media. The CA/ATPNIPAAm micelles exhibited a lower critical solution temperature (LCST) at $31.5^{\circ}C$. Micelle sizes measured by photon correlation spectroscopy (PCS) were approximately 31.6 $\times$$\times$ 5.8 nm. The CA/ATPNIPAAm micelles were spherical and their thermal size transition was observed by transmission electron microscope (TEM). A fluorescence probe technique was used for determining the micelle formation behavior of CA/ATPNIPAAm in aqueous solutions using Pyrene as a hydrophobic Probe. The critical micelle concentration (CMC) was evaluated as $8.9{\times}0^{-2}$ g/L. A drug release study was performed using indomethacin (IN) as a hydrophobic model drug. The release kinetics of IN from the CA/ATPNIPAAm micelles revealed a thermo-sensitivity by the unique character of poly(N-isopropylacrylamide) i.e. the release rate was higher at $25^{\circ}C$ than at $37^{\circ}C$.

• Macromolecular Research
• /
• v.12 no.1
• /
• pp.107-111
• /
• 2004

We have studied the polymerization kinetics of acrylamide in aqueous solution with potassium persulfate as an initiator by using quantitative real-time in situ IR spectroscopy and monitoring the profiles of peaks in the range 1900-850 cm$\^$-1/. The conversion of acrylamide was calculated from the disappearance of the peak at 988 cm$\^$-1/, which is the out-of-plane bending mode of the=C-H unit, normalized to the C=O stretching peak at 1675 cm$\^$-1/, as an internal standard. For reaction temperatures in the range 40-65$^{\circ}C$ and initiator and monomer concentrations of 0.9-2.6 mmol/L and 0.5-1.1 mol/L, respectively, we deduced that the rate of monomer consumption follows the relation R$\_$p/=k［K$_2$S$_2$O$\_$8/］$\^$0.5/ [Μ］$\^$1.35${\pm}$0.10/. In addition, we obtained activation parameters from an evaluation of the kinetic data.

• Archives of Pharmacal Research
• /
• v.26 no.6
• /
• pp.478-481
• /
• 2003

Phospholipase D is a ubiquitous enzyme that plays an important role in various lipid mediated cellular signaling pathways and produces rare phospholipids, phosphatidylethanol or phosphatidylbutanol, instead of phosphatidic acid with unique catalytic activity transphosphatidylation in the presence of primary alcohols. The reaction products, phosphatidylethanol or phosphatidylbutanol are used as markers of in vitro phospholipase D activity in many studies. For the sensitive detection of the phospholipase D products, we developed an advanced lipid extraction method that facilitates recovery of the compounds. With the new method, the activity change of phosaholipase D by agonists could be detected more easily and the recovery rate was also increased. The increase of detected enzyme activity change was about double fold compared to the conventional lipid extraction method. This method provides selective force for the phospholipase D products in the extraction procedure.

• Journal of the Korean Ceramic Society
• /
• v.37 no.8
• /
• pp.760-767
• /
• 2000

Recently, the protection of construction is demanded with environmental pollution. These protect modes are use of concrete admixture, coat of protective polymer and impregnate of surface with chemicals etc. The most widely used impregnation is economical and effective. The define of Impregnation for construction protect is reacted in and consolidated substrate after absorbed. The impregnation agents are Polyesters, Acrylic monomers, Epoxy and Silicone derivatives. Commonly, because the Silane has good water repellency and environmental advantages that it widely used to water proofing agents, dampproofing agents and absorption reducer for concrete of bridges. When application of Silane, it occurs pollution and harmfulness as included organic solvent. The manufactures have tired to emulsification of Silane for the reducing of the defects. The Silane emulsion is vary unstable and does not stored long periods, and it is diminished in good properties with internal reaction. In this study we tried to emulsification of Silane for effectiveness improvement and reduce pollution and hazard and discussed properties variation of emulsion. The Silane emulsions are achieved emulsifying with W/O and O/W type surfactants. It used 0.24% PVA as protective colloid and stable phase is creamy. The creamy Silane emulsion performance as the penetration depth and water absorption rate are above 4 mm and below 0.1. It stable about 6 month at room temperature.

• Journal of the Korean Institute of Electrical and Electronic Material Engineers
• /
• v.37 no.1
• /
• pp.56-62
• /
• 2024

By introducing curing kinetics and chemo-rheology for the epoxy resin formulation for ultra-high voltage gas insulated switchgear (GIS) Insulating Spacers, a study was conducted to simulate the curing behavior, flow and warpage analysis for optimization of the molding process in automatic pressure gelation. The curing rate equation and chemo-rheology equation were set as fixed values for various factors and other physical property values, and the APG molding process conditions were entered into the Moldflow software to perform optimization numerical simulations of the three-phase insulating spacer. Changes in curing shrinkage according to pack pressure were observed under the optimized process conditions. As a result, it was confirmed that the residence time in the solid state was shortened due to the lowest curing reaction when the curing holding pressure was 3 bar, and the occurrence of deformation due to internal residual stress was minimized.

• Clean Technology
• /
• v.26 no.4
• /
• pp.329-335
• /
• 2020

Methanol synthesized from renewable hydrogen and captured CO2 has recently attracted great interest as a sustainable energy carrier for large-scale renewable energy storage. In this study, molten carbonate fuel cell's performance was investigated with the direct conversion of methanol into syngas inside the anode chamber of the cell. The internal reforming of methanol may significantly improve system efficiency since the heat generated from the electrochemical reaction can be used directly for the endothermic reforming reaction. The porous Ni-10 wt%Cr anode was sufficient for the methanol steam reforming reaction under the fuel cell operating condition. The direct supply of methanol into the anode chamber resulted in somewhat lower cell performance, especially at high current density. Recycling of the product gas into the anode gas inlet significantly improved the cell performance. The analysis based on material balance revealed that, with increasing current density and gas recycling ratio, the methanol steam reforming reaction rate likewise increased. A methanol conversion more significant than 90% was achieved with gas recycling. The results showed the feasibility of electricity and syngas co-production using the molten carbonate fuel cell. Further research is needed to optimize the fuel cell operating conditions for simultaneous production of electricity and syngas, considering both material and energy balances in the fuel cell.

• Tuberculosis and Respiratory Diseases
• /
• v.59 no.3
• /
• pp.279-285
• /
• 2005

Background : Ambient particles during Asian dust events are usually less than $10{\mu}m$ in size, and known to be associated with the adverse effects on the general population. There is little evidence linking Asian dust to adverse effects on the airways. In 2002, the authors found that particulate matter during Asian dust events had an effect on the symptoms and pulmonary function of patients with bronchial asthma. An aggravating factor might be that of a viral infection, but this remains unclear. Conversely, it has been speculated that African dust may carry the virus responsible for foot and mouth disease. Asian dust events are also likely to be responsible for transporting viruses, some of which are pathogenic, and common in many environments. Therefore, in this study, air samples were screened for the presence of viruses. Methods : Air samples were collected 20 times each during Asian dust events and under non-dust conditions, for at least 6 hours per sample, using a high volume air sampler (Sibata Model HV500F), with an airflow rate of 500L/min, between April and August 2003, and between April and August 2004. The samples were then screened for the presence of targeted viruses (Influenza A, B, Hog cholera virus, and Aphthovirus) using a polymerase chain reaction method. Results : One Asian dust event occurred between April and August 2003, and 3 between April and August 2004, with a 24 hour average PM10 level of $148.0{\mu}g/m^3$. The 24 hour average PM10 level was $57{\mu}g/m^3$. There was a significant difference in the PM10 concentration between dusty and clear days. No viruses (Influenza virus, Aphthovirus, and Hog cholera virus) were identified in the air samples obtained during the dusty days. Conclusions : Although no virus was detected in this study, further studies will be needed to identify suspected viruses carried during Asian dust events, employing more appropriate virus detection conditions.

• Tuberculosis and Respiratory Diseases
• /
• v.40 no.5
• /
• pp.584-594
• /
• 1993

Background: Among the respiratory diseases, there are a lot of cases of pleural effusion. The most common cause is tuberculosis. But the other cause such as lung malignancy is in an increasing tendency because of the development of diagnostic procedure, the decrease of the prevalence of the tuberculosis and the increase of the longevity. We need to know the accurate diagnosis as soon as possible for the correct therapy. Method: A clinical observation was made on 315 cases of pleural effusion seen at Pusan Adventist Hospital, from Jan, 1989 to Dec, 1992. For diagnostic procedure, thoracentesis, lymph node biopsy, bronchoscopy and percutaneous biopsy of the parietal pleura with Cope needle were performed. The following are parameters used in seperating the exudate from the transudate: pleural protein 3.0 g/dl, pleural protein/serum protein ratio 0.5, pleural LDH 200 IU, pleural LDH/serum LDH ratio 0.6, pleural cholesterol 60 mg/dl and pleural cholesterol/serum cholesterol ratio 0.3. Each parameters were compared, and misclassified rate and diagnostic efficiency were calculated. Results: The most common cause of exudate pleurisy was tuberculosis (82.3%) and malignancy was next (12.2%). The chief complaints of pleural effusion were noted as dyspnea (58.7%), chest pain (54.9%), coughing (50.2%) and fever (36.2%). Location of pleural effusion was noted as right side (51.4%), left side (41.3%) and both sides (7.3%). Amount of pleural effusion of the chest X-ray was minimum (46.8%), moderate (40.5%) and maximum (12.7%). Misclassified rates for each parameters in seperating the exudates from the transudates were as follows; protein: 5.2%, pleural protein/serum protein:7.6%, LDH: 13.9%, pleural LDH/serum LDH: 6.9%, cholesterol: 8.0%, pleural cholesterol/serum cholesterol: 5.6%. On the pleural biopsy, the tuberculosis granuloma was 60.8%, malignancy was 13.6%, infection was 2.3% and nonspecific inflammatory reaction was 23.3%. Conclusion: on the basis of the above results, the most common cause of exudative pleurisy was tuberculosis. We think that the plerual cholesterol/serum cholesterol ratio is the most useful supportive parameter in separating the exudates from the transudates. For accurate diagnosis, the pleural biopsy is the first procedure and repeated pleural biopsy of nonspedcific inflammatory reaction is required.

• Journal of The Korean Society of Agricultural Engineers
• /
• v.49 no.2
• /
• pp.75-86
• /
• 2007

This process which has a connection of biofilter and sulfur-limestone has been developed to treat organic substances including BOD, COD and SS etc. and to treat sulfur-limestone is for denitrification.. The whole process consists of chemical reaction tank, sedimentation tank, trickling filter, denitrification tank The trickling filter is equipped with a reactor filled with absorptive filter, and the sulfur denitrification tank is filled with sulfur-limestone mixed media. After setting up practical facilities whose capacity is 60 tons a day, we have observed the removal efficiencies of pollutants through 60 experiments during Summer and Winter seasons. The average concentration of polluted water was BOD for 3.6 mg/L, $COD_{Mn}$ for 11.3 mg/L, SS for 2.8 mg/L, T-N for 8.6 mg/L, and T-P for 0.8 mg/L, and the rate of treatment efficiencies 96.5%, 84.7%, 96.5%, 79.2%, and 80.8%, respectively was found through the experiments. The average treatment efficiency for BOD and $COD_{Mn}$ was 85.0% and 55.7%, respectively and the average removal efficiency for NH4+-N was 84.9% in the trickling filter. The removal efficiency in the denitrification tank is as follows; The removal rate of $NO_3^--N$ was as high as 93.2% within the compass of pH 6.3 to 7.3 through $16.8{\sim}37.0mg/L$ flown into $NO_3^--N$ and $0.1{\sim}8.3mg/L$ outflown. It had observed that this process has implemented highly efficient and advanced treatment without external carbon sources and internal recycle during its process. In conclusion, this process is suitable for a sewerage in a small village due to the merits of low power consumption and easy maintenance.