• Journal of Biomedical Engineering Research
• /
• v.27 no.4
• /
• pp.143-153
• /
• 2006

The purpose of this work was to assess and quantify the beneficial effects of gas exchange, while testingto the various frequencies of the sinusoidal wave that was excited by the PZT actuator, for patients suffering from acute respiratory distress syndrome (ARDS) or chronic respiratory problems. Also, this paper considered a simulator to design a hollow type artificial lung, and a mathematical model was used to predict a behavior of blood. This simulation was carried out according to the Montecarno's simulation method, anda fourth order Runge-Kutta method was used to solve the equation. The experimental design and procedure are then applied to the construction of a new device to assess the effectiveness of the membrane vibrations. As a result, the vibration method is very effective in the increase of gas transport. The gas exchange efficiency for the vibrating intravascular lung assist device can be increased by emphasizing the following design features: consistent and reproducible fiber geometry, and most importantly, an active means of enhancing convective mixing of water around the hollow fiber membranes. The experimental results showed the effective performance of the vibrating intravascular lung assist device. Also, we concluded that important design parameters were blood flow rates, fiber outer diameter and oxygen pressure drop. Based on the present results, it was believed that the optimal level of blood flow rates was 200$cm^3$/min.

• Journal of Biomedical Engineering Research
• /
• v.27 no.1
• /
• pp.30-37
• /
• 2006

Injecting currents into an electrically conducting subject, we may measure the induced magnetic flux density distributions using an MRI scanner. The measured data are utilized to reconstruct cross-sectional images of internal conductivity and current density distributions in Magnetic Resonance Electrical Impedance Tomography (MREIT). Injection currents are usually provided in a form of mono-polar or bi-polar pulses synchronized with an MR pulse sequence. Given an MRI scanner performing the MR phase imaging to extract the induced magnetic flux density data, the current source becomes one of the key parts determining the signal-to-noise ratio (SNR) of the measured data. Since this SNR is crucial in determining the quality of reconstructed MREIT images, special care must be given in the design and implementation of the current source. This paper describes a current source design for MREIT with features including interleaved current injection, arbitrary current waveform, electrode switching to discharge any stored charge from previous current injections, optical isolation from an MR spectrometer and PC, precise current injection timing control synchronized with any MR pulse sequence, and versatile PC control program. The performance of the current source was verified using a 3T MRI scanner and saline phantoms.

• Journal of Advanced Navigation Technology
• /
• v.17 no.5
• /
• pp.560-567
• /
• 2013

In this paper, it is proposed the fault detection method of the ASIC, without the Test Requirement Document(TRD), extracting internal logic circuit and analyzed the function of the ASIC using the multipurpose development program and simulation. If there don't have the TRD, it is impossible to analyze the operation of the circuit and find out the fault detection in any chip. Therefore, we make the TRD based on the analyzed logic data of the ASIC, and diagnose of the ASIC circuit at the gate level through the signal control of I/O pins using the Dynamic Pattern signal. According to the experimental results of the proposed method, we is confirmed the good performance of the fault detection capabilities which applied to the non-memory circuit.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.421-428
• /
• 2004

This study concerns the characteristics of boiling heat transfer in two-phase closed thermosyphons with various micro grooves. A study was carried out with the performance of the heat transfer of the thermosyphon having 60 internal micro grooves in which boiling and condensation occur. A plain thermosyphon having the same inner and outer diameter as the grooved thermosyphon is also tested for comparison. Distilled water, methanol, ethanol have been used as the working fluid. The heat flux and the boiling heat transfer coefficient at the evaporator zone are estimated from the experimental results. The experimental results have been assessed and compared with existing correlations. Imura's and Kusuda's correlation for boiling showed in good agreement with experimental results within ${\pm}20{\%}$ in plain thermosyphon.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.5 no.5
• /
• pp.447-453
• /
• 2004

In this paper, we propose a new system to block harmful Internet information based on IP spoofing. The proposed system is located on a organization's internal network and monitors all outgoing traffic and lets all this traffic go outside. Once the proposed system detects a host's access to a harmful site, it sends the host a pseudo RST packet that pretends to be the response from the harmful site, and prevents the connection between the host and the harmful site. The proposed software system is installed on only a server, and need not be installed on user hosts at all. Thus we can maintain and upgrade the blocking system easily. The performance evaluation of the proposed system shows that it effectively blocks the access to the harmful sites. Since the proposed system is based on IP spoofing, it can be used badly as a hacking tool. Finally we propose some methods to eliminate this possibility.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.12 no.5
• /
• pp.942-947
• /
• 2008

A cluster server usually consists of a front end node and multiple backend nodes. Though increasing the number of bookend nodes can result in the more QoS(Quality of Service) streams for clients, the possibility of failures in backend nodes is proportionally increased. The failure causes not only the stop of all streaming service but also the loss of the current playing positions. In this paper, when a backend node becomes a failed state, the recovery mechanisms are studied to support the unceasing streaming service. The basic techniques are hewn as providing very high speed data transfer rates suitable for the video streaming. However, without considering the architecture of cluster-based VOD server, the application of these basic techniques causes the performance bottleneck of the internal network for recovery and also results in the inefficiency CPU usage of backend nodes. To resolve these problems, we propose a new failure recovery mechanism based on the pipeline computing concept.

• Journal of Radiation Industry
• /
• v.9 no.1
• /
• pp.1-7
• /
• 2015

The trend of x-ray image sensor has been evolved from an amorphous silicon sensor to a crystal silicon sensor. A crystal silicon X-ray sensor, meaning a X-ray CIS (CMOS image sensor), is consisted of three transistors (Trs), i.e., a Reset Transistor, a Source Follower and a Select Transistor, and a photodiode. They are highly sensitive to radiation exposure. As the frequency of exposure to radiation increases, the quality of the imaging device dramatically decreases. The most well known effects of a X-ray CIS due to the radiation damage are increments in the reset voltage and dark currents. In this study, a pixel array of a X-ray CIS was made of $20{\times}20pixels$ and this pixel array was exposed to a high radiation dose. The radiation source was Co-60 and the total radiation dose was increased from 1 to 9 kGy with a step of 1 kGy. We irradiated the small pixel array to get the increments data of the reset voltage and the dark currents. Also, we simulated the radiation effects of the pixel by MCNP (Monte Carlo N-Particle) simulation. From the comparison of actual data and simulation data, the most affected location could be determined and the cause of the increments of the reset voltage and dark current could be found.

• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.20 no.10
• /
• pp.107-116
• /
• 2019

The defense industry has recently been developed for boosting exports of weapon systems. The survey and analysis of the quality level are required to form a relevant policy for expanding the defense industry. Evaluation indices and modeling of the quality level for manufacturers are used to examine the status of internal quality management and quality management system in order to enhance the overall quality level and establish a quality policy in the field of military supplies. There were some restrictions to apply all aspects of the quality level in the previous model. This paper deals with the research and analysis of other types of model for evaluating the quality level, including the model used in the defense field. By enhancing the close link between procedure indices and performance indices, the research and analysis could be conducted objectively and intuitively. The developed and improved model and indices will be used in the next survey of the quality level for manufacturers of military supplies. The survey results will be used to establish effective government quality management policy.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.20 no.4
• /
• pp.68-76
• /
• 2016

This research is carried out for the performance evaluation of the injector that is one of the critical components of bipropellant-rocket-engine. Spray characteristics are investigated in detail according to the recess length and injection pressure on the swirl-coaxial-injector using gaseous methane and liquid oxygen as propellants. A visualization is conducted by the Schlieren photography that is composed of a light source, concave mirrors, knife, and high-speed-camera. A hollow-cone-shape is identified in the liquid spray that is spread only by inner injector and the spray angle is decreased due to the diminution of swirl strength in accordance with the increase of the length of injector orifice. When the injector sprays the liquid through the inner injector with the aid of gas through the outer injector, the spray angle in external mixing region tends to increase with rise of the recess length, while in internal mixing region, it is decreased. It is also confirmed that the same tendency of the spray angle with recess length appears irrespective of the injection pressure of liquid spray.

• Journal of the Korean Society of Propulsion Engineers
• /
• v.14 no.4
• /
• pp.32-38
• /
• 2010

Heat transfer coefficients in a dimpled channel, a ribbed channel, and a rip-dimple compound channel were measured by the transient liquid crystal technique. The channel aspect ratio, the rib height, the rip pitch, and the rib angle were 4:1, 6 mm, 60 mm and $60^{\circ}$, respectively. The dimple diameter and the center-to-center distance were 6mm and 7.2 mm, respectively, and the Reynolds number range was 30,000-50,000. Results showed that the heat transfer coefficients were increased by the angled rib. For the dimple-rib compound cooling cases, the heat transfer coefficients were further augmented and the thermal performance factor for the case was the highest.