• Bulletin of the Korean Chemical Society
• /
• v.6 no.2
• /
• pp.95-98
• /
• 1985

Stereospecific [2 + 2] cycloadducts are obtained as major products when trans-cinnamonitrile derivatives are irradiated with excess tetramethylethylene. The fluorescence quenching studies, weak exciplex fluorescence, and sensitization by benzophenone suggest that this stereospecific photochemical cycloaddition reaction involves singlet exciplex intermediate formed between cinnamonitrile derivatives and tetramethylethylene.

• Journal of Korea Foundry Society
• /
• v.10 no.4
• /
• pp.299-308
• /
• 1990

Ductile cast iron has a good ductility and ductility and toughness than those of gray cast iron, because the shape of graphite is spheroidal. It has been reported that the strengthening and toughening of the ductile cast iron was resulted from the good modification of various matrix structures obtained by the heat treatment or addition of alloying elements. This study aims to investigate the effect of various special heat treatment(Cyclic Heat Treatment, Intermediate Heat Treatment, Step Quenching), austempering and alloying element(Ni) on the strength and toughness of ductile cast iron. The results obtained from this study are summarized as follows. 1) With addition of Ni, the amount of pearlite or bainite were increased and the morphologies of pearlite or bainite became finer by special heat treatments. 2) As the Ni added and not added ductile cast iron were treated by austenitizing at $900^{\circ}C$ and $840^{\circ}C$, in the latter the austenite was mostly formed in the vicinity of eutectic cell boundary, but in the former on the whole matrix. 3) In cyclic heat treatment, the volume fraction of pearlite was increased and the shape of pearlite was fined with increase of the number of cycle. 4) The shape of pearlite was mostly bar type in the intermediate heat treatment, but spheroidal type in step quenching. 5) The mechanical properties of ductile cast iron containing 1.5%Ni austempered at $400^{\circ}C$ for 25min. after austenitizing at $900^{\circ}C$ for 15min. were a good value of hardness 105(HRB), impact energy 12.5(kg.m), tensile strength 112($kg/mm^2$) and elongation 6.8(%).

• Journal of Plant Biology
• /
• v.34 no.4
• /
• pp.303-309
• /
• 1991

Limitation of photosynthesis in detached Chinese cabbage (Brassica campestris L.) leaves was induced by feeding of mannose (25 mM) for 12 h in the light, and changes in the basic thylakoid functions under this condition were investigated. The acid soluble phosphate contend and CO2 uptake rate was decreased by 66% and 67%, respectively. However, the starch content was increased by 24% compared to those of controls. From the fast induction curves of chlorophyll fluorescence, dark level fluorescence (Fo) slightly increased while intermediate plateau fluorescence level (FI) to peak level fluorescence (Fp) transient was significantly decreased with a slight decrease in the Fo-to-FI transient. This data means that reduction of secondary electron acceptor of PSII (QB) might be more severely inhibited than that of primary electron acceptor of PSII (QA) by decrease in phosphate level. The strong decline of (Fv)m//Fm ratio suggests that efficiency of excitation energy capture by PSII was decreased markedly. The quenching of Fo (qO), an indicator of state transition, was also occurred over the slow induction kinetics of chlorophyll fluorescence. From quenching analysis, fluorescence was dominantly quenched by nonphotochemical quenchings (qE+qT). These results showed that the capture and transfer efficiency of excitation energy to PSII reaction center in thylakoid was decreased with the decline of leaf phosphate level, and that the state transition was occurred during the induction of photosynthesis under these conditions.

• Journal of Photoscience
• /
• v.5 no.3
• /
• pp.125-129
• /
• 1998

Occurrence of an electron (or H atom equivalent to one electron plus H+) transfer from $\alpha$- tocopherol $\alpha$(TOH) to a number of photosensitizers in theri triplet states were investigated by monitoring the ESR signal of $\alpha$-chromaoxyl radical ($\alpha$(TO.) in ethanolic solutions of $\alpha$TOH and the sensitizers under continuous illumination. Every sensitizer molecule examined, such as protocholorophyllide (Pchl), hematoporphyrin and rose bengal which are generally regarded as efficient type II photosensitizers and thus have long-lived triplet states, was found to actively participate in an electro transfer reaction with $\alpha$TOH even under air-saturation conditions, generating $\alpha$TOH complex as an intermediate in a fashion of Michaelis-Menten type of reaction. For the reaction of $\alpha$TOH with triplet Pchl, the rate law was derived by applying the steady approximation for the binary complex, triplet Pchl-$\alpha$TOH , which turned out to be well consistent with the kinetic data.

• Journal of Korea Foundry Society
• /
• v.11 no.5
• /
• pp.406-413
• /
• 1991

Ductile cast iron(DCI) with a multi-phase(ferrite-bainite-martensite) structures was produced by various special heat treatment. Intercritical heat treatment(I. C.), intermediate heat treatment(I. M.) and step quenching(S. Q.) were used to strengthen and toughen the fracture initiation sites such as graphite-marix interfaces and eutectic cell boundaries in DCI. The purpose of this study was to investigate of DCI by the special heat treatment. (I. C., I. M., and S. Q.) At a result, bainite nucleation rate at higher temperature was higher than that of at lower temperature, and shapes of bainite and martensite became bar /spheroidal type with increase of isothermal transformation time.

• Korean Journal of Materials Research
• /
• v.30 no.1
• /
• pp.8-13
• /
• 2020

Effect of heat treatment on microstructure and mechanical properties of an Fe-6.5Mn-0.08C medium-manganese steel is investigated in this study. Three kinds of medium-manganese steel specimens are fabricated by varying heat treatments of intermediate quenching (IQ), step quenching (SQ), and intercritical annealing (IA). Hardness and tensile tests are performed to examine the correlation of microstructure and mechanical properties for the Fe-6.5Mn-0.08C medium-manganese steel specimens. The IQ and SQ specimens have microstructures of martensite matrix with ferrite, whereas IA specimen exhibits microstructure of acicular ferrite matrix with martensite. The tensile test results show that the SQ specimen with martensite matrix has the highest yield strength and the lowest elongation. On the other hand, the SQ specimen has the highest hardness due to the relatively lower reduction of carbon content in martensite during intercritical annealing. According to the fractography of tensile tested specimens, the SQ specimen exhibits a dimple and quasi-cleavage fracture appearance while the IQ and IA specimens have fully ductile fracture appearance with fine-sized dimples caused by microvoid coalescence at ferrite and martensite interface.

• Proceedings of the KSME Conference
• /
• 2001.06e
• /
• pp.57-62
• /
• 2001

Korea Atomic Energy Research Institute (KAERI) launched an intermediate scale steam explosion experiment named Test for Real cOrium Interaction with water (TROI) using reactor material to investigate whether the corium would lead to energetic steam explosion when interacted with cold water at low pressure. The melt-water interaction is confined in a pressure vessel with the multi-dimensional fuel and water pool geometry. The cold crucible technology, where the mixture of powder in a water-cooled cage is heated by high frequency induction, is employed. In this paper, results of the first series of tests ($TROI-1{\sim}5$) were discussed. The ZrO2 jets with 5kg mass and 5cm diameter were poured into the 67cm deep water pool at $30{\sim}95^{\circ}C$. Either spontaneous steam explosions or quenching was observed. The morphology of debris and pressure wave profiles clearly indicates the each case.

• Journal of the Korean Society for Heat Treatment
• /
• v.18 no.5
• /
• pp.288-296
• /
• 2005

The corrosion behaviors of Zr-based alloys were very sensitive to their microstructures which were determined by manufacturing process. The specimens of Zr-based alloy named as HANA-4 for nuclear fuel cladding were investigated in order to get the optimized manufacturing process such as the intermediate annealing temperature and cold working steps after the ${\beta}$ quenching. From the microstructural analysis, cold worked microstructure of the samples was changed to the recrystallized microstructure by performed process. The corrosion behaviors of HANA-4 alloy were affected by the different manufacturing process. The ${\beta}$-Zr phase was formed in the matrix and the Nb concentration in the ${\beta}$-Zr phase was increased as progressing the manufacturing process. So, it was found that the corrosion rate of HANA-4 alloy was affected by the Nb concentration in the matrix.

• Proceedings of the Membrane Society of Korea Conference
• /
• 2002.05a
• /
• pp.81-85
• /
• 2002

Small angle light scattering and field emission scanning electron microscope have been used to quantify the kinetics of liquid-liquid separation behavior during water vapor(RH52%[$\pm$3%] at 27$^{\circ}C$) quenching (non-solvent induced phase separation, NIPS) of polysulfone/NMP/Alcohol and CPVC/THF/Alcohol, respectively. Time dependence of the position of the light scattering maximum was observed at polysufone dope solutions, confirming spinodal secomposition (SD). while CPVC dope solutions showed a decreased scattered light intensity with a increased q-valuel, indicating nucleation & growth (NG). For the each system, domain growth rate in the intermediate and late stage of phase separation decreased with increasing the number of carbon of alcohol used as additive (non-solvent). Also, in the early stage for SD, the scattering intensity with time was in accordance with Cahns linear theory of spinodal decomposition,[1-3] regardless of types of non-solvent additive.

• Journal of Korea Foundry Society
• /
• v.10 no.2
• /
• pp.144-153
• /
• 1990

Ductile cast iron has good ductility and toughness, for the graphite morphology is spheroidal. It has been reported that the strengthening and toughening of the ductile cast iron was resulted from the modification of matrix structure by the heat treatment or the addition of alloying elements. In this study, effects of various special heat treatments (cyclic heat treatment and intermediate heat treatment) and Ni addition on the toughness and strength of the austempered ductile cast iron were studied. The results obtained from this study were as follows : 1. The amount of fine pearlite was increased with the Ni content and the number of cycle in cyclic heat treatment. 2. When the specimens treated and not by special heat treatment at 820 was austempered, in the former the austenite was formed on grain boundary entirely, but in the latter on grain boundary partially. 3. The impact energy was decreased with the Ni content, because the coarisen austenite pools formed with the Ni content was transformed into martensite during quenching. 4. The mechanical properties of austempered ductile cast iron containing 2%Ni treated cyclic heat treatment(5 cycles)was very excellent in handness 99(HRB), impact energy 12(kg-m) maximum fracture load 1500(kg-f).