• Proceedings of the KIEE Conference
• /
• 1991.11a
• /
• pp.101-104
• /
• 1991

Design characteristics of Interior Permanent Magnet Synchronous Motors are induced. In order to maximize the efficiency of the motor, the objective function is taken stator winding and core losses. And using Sequential Unconstrained Minimization Technique, the dimensions of the motor are obtained which minimize the objective function. Characteristics of the motor which is designed as above are compared with the conventional one.

• Proceedings of the KIEE Conference
• /
• 2006.07b
• /
• pp.771-772
• /
• 2006

Recently, Interior Permanent Magnet Synchronous Motor(IPMSM) is widely used in the industry applications such as power train for hybrid vehicles and compressor motors of air-conditioner due to its high power density and wide speed range. In designing motors, pole slot combination should be chosen properly according to the use of the motor and driving method in the initial design stage, accordingly there have been many researches about pole slot combination. As a part of the studies, this paper presents a comparison of characteristics of concentrated winding IPMSM, such as back-emf, Total Harmonic Distortion(THD) and core losses for each pole slot combination. By comparing the characteristics of each model, this paper can be a guide or reference in determining pole slot combination in the initial design stage.

• Proceedings of the KIEE Conference
• /
• 2015.07a
• /
• pp.83-84
• /
• 2015

In order to use the high-speed range of Interior Permanent Magnet Synchronous Motor(same as IPMSM above), the motor should be at flux weakening control status. High-speed range is called field weakening control region or constant power region, and explain the basic theory of flux weakening control used in the constant power region. Back electromotive force of IPMSM is measured. and field weakening conrtrol driving characteristics is configurated verification test. Through experimentation speed-torque characteristic curve, the efficiency variation corresponding to the current phase angl,the efficiency map were produced.

• Proceedings of the KIPE Conference
• /
• 1998.07a
• /
• pp.305-308
• /
• 1998

This paper describes a development of interior permanent magnet synchronous motor (IPMSM) and driver for electric vehicle (EV) which is driven by 2 motors without differential gear. A inverter is designed to drive 2 motors with 6 legs IGBT switches in a control board. Also vector control algorithm is implemented with maximum torque control method in the constant torque region and field weakening control method considering inverter capacity in the constant power region. Prototype IPMSM and inverter have been developed. To verify dynamic characteristics of the those about torque to speed and efficiency etc. We are making an experiment on that. Though that is not completed, we will show results to be acquired.

• The Transactions of the Korean Institute of Electrical Engineers B
• /
• v.54 no.6
• /
• pp.269-277
• /
• 2005

In this paper, designs of an Interior Permanent Magnet Synchronous Motor (IPMSM) and its motor driver for 42V automotive air condition system are introduced. The characteristics of the IPMSM are predicted by using d-q equivalent circuit having the parameters, such as current phase angle, d-q axis inductances, core loss resistance, etc. The experimental and analysis results of the prototype are compared to show validity of the analysis method, and to give analyzed characteristics in detail. As the result, an improved IPMSM is designed to widen the operating speed limit of prototype; a cost effective AC drive are considered at the same time.

• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.26 no.3
• /
• pp.61-68
• /
• 2012

This paper deals with a fault diagnosis algorithm for open faults in the switching devices of PWM inverter-fed IPMSM (Interior Permanent Magnet Synchronous Motor) drive. The proposed diagnostic algorithm is realized in the controller using the informations of three-phase currents or reference line-to-line voltages, without requiring additional equipments for fault detection. Under switch open fault conditions, the conventional dq model used to control an AC motor cannot directly be applied for the analysis of drive system, since three-phase balanced condition does not hold. To overcome this limitation, a fault model based on the line-to-line voltages is employed for the simulation studies. For comparative performance evaluation through the experiments, the entire control system is implemented using digital signal processor (DSP) TMS320F28335. Simulations and experimental results are presented to verify the validity of the proposed diagnosis algorithm.

• Journal of the Korean Magnetics Society
• /
• v.27 no.2
• /
• pp.54-62
• /
• 2017

This paper presents a design of the Interior Permanent Magnet Synchronous Motor (IPMSM). an initial design process is accomplished by using the parametric design. In the design process, motor characteristics of parameters is computed by the d-q axis equivalent circuit model. Then, an optimal design process is accomplished by combination the experimental design and the response surface method. Finally, the design and analysis results are verified with experimental results.

• Journal of Electrical Engineering and Technology
• /
• v.13 no.3
• /
• pp.1241-1250
• /
• 2018

Parallel three-phase voltage source inverters in a direct connection configuration are widely used to increase system power ratings. A zero-sequence circulating current can be generated according to the switching method; however, the zero-sequence circulating current not only distorts current, but also reduces the system reliability and efficiency. In this paper, a model predictive control scheme is proposed for parallel inverters to drive an interior permanent magnet synchronous motor with zero-sequence circulating current suppression. The voltage vector of the parallel inverters is derived to predict and control the torque and stator flux components. In addition, the zero-sequence circulating current is suppressed by designing the cost function without an additional current sensor and high-impedance inductor. Simulation and experimental results are presented to verify the proposed control scheme.

• Journal of Power Electronics
• /
• v.19 no.4
• /
• pp.956-967
• /
• 2019

This paper introduces a virtual signal injected maximum torque per ampere (MTPA) control strategy for direct-torque-controlled five-phase interior permanent magnet synchronous motor (IPMSM) drives. The key of the proposed method is that a high frequency signal is injected virtually into the stator flux linkage. Then the responding stator current is calculated and regulated to compensate the amplitude of the flux linkage. This is done according to the relationship between the stator current and the stator flux linkage. Since the proposed method does not inject any real signals into the motor, it does not cause any of the problems associated with high-frequency signals, such as additional copper loss and extra torque ripple. Simulation and experimental results are offered to verify the effectiveness of the proposed method.

• Journal of Magnetics
• /
• v.18 no.2
• /
• pp.216-219
• /
• 2013

In this paper, the influence of inverter switching harmonics on iron loss and PM loss of Permanent Magnet Synchronous Motor (PMSM) is numerically investigated by Finite Element Method (FEM). In particular, nonlinear FEM is applied for a multi-layered PM Synchronous Motors (PMSMs), Interior buried PMSM (IPMSM) and PM assisted Synchronous Reluctance Motor (PMa-SynRM), which are adoptively designed and compared for Electric Vehicle (EV) propulsion. In particular, iron loss and PM eddy-current loss under the real current waveform including the carrier harmonics from inverter switching are numerically analyzed with nonlinear FEM by considering the skewed stator structure employed for minimizing spatial harmonics.