• 대한치과기공학회지
• /
• 제35권2호
• /
• pp.137-142
• /
• 2013

Purpose: This study was to observe the surface and interfacial characteristic of Zirconia by surface treatment. And it was observed the roughness and contact angle according to processing, and the interfacial properties by surface treatment on zirconia. Methods: The oxide formation and ion diffusion between core and veneer ceramic were determined by the X-ray Dot Mapping of EPMA(Electron probe micro analyzer). The roughness was measured by 3D Digital microscope and the contact angle according to processing of zirconia was observed using distilled water on the surface. Results: The surface roughness of the specimens Z04, Z12, Z15 was measured $0.67({\pm}0.03){\mu}m$, $0.50({\pm}0.12){\mu}m$, $0.35({\pm}0.09){\mu}m$, respectively. As results of contact angle test, Z04, Z12, Z15 of specimen group without binder treatment was measured $46.79({\pm}3.17)^{\circ}$, $57.47({\pm}4.83)^{\circ}$, $56.19({\pm}2.66)^{\circ}$, respectively. but, L04, L12, L15 of specimen group without binder treatment was measured $63.84({\pm}2.20)^{\circ}$, $66.08({\pm}0.16)^{\circ}$, $65.10({\pm}1.01)^{\circ}$, respectively. Average contact angle of L15 was measured $65.10({\pm}1.01)^{\circ}$. In X-ray Dot Mapping results, thickness of binder including Al element was measured that each of L04, L12, L15 were $20{\mu}m$, $15{\mu}m$, $10{\mu}m$. Conclusion: The more rough surface increases the wettability, but the sintered exclusive binder decreases the wettability.

• 접착 및 계면
• /
• 제12권1호
• /
• pp.26-33
• /
• 2011

폴리케톤 필름의 산처리 조건에 따른 필름 표면의 화학적인 변화를 접촉각과 XPS를 이용하여 분석하고, 모폴로지의 변화를 SEM과 AFM을 통하여 살펴보고, 최종적으로 이러한 변화가 폴리케톤 필름과 고무와의 계면접착력에 어떠한 영향을 미치는지를 살펴보았다. 인산처리에 의하여 폴리케톤 필름의 표면에 젖음성이 증가하여 인산의 농도 및 처리시간에 따라서 접촉각이 감소하였으며, 표면에 산소함유기들이 증가하는 결과를 보였다. 인산농도와 처리시간이 증가함에 따라 표면에 crack과 etching이 증가하여 표면거칠기가 증가하였으나, 산처리 조건이 강화되면서 폴리케톤 필름의 표면에 degradation이 발생하여 roughness가 감소하는 결과를 보였다. 폴리케톤과 고무와의 계면접착력을 살펴본 결과, pH 0.74에서 120 min, pH 0.4에서 60 min 처리한 경우에 최대 계면접착력을 보였으며, 산처리 조건이 그 이상으로 증가하면서 degradation이 발생하면서 계면접착력이 감소하였다.

• Journal of Periodontal and Implant Science
• /
• 제50권2호
• /
• pp.106-120
• /
• 2020

Purpose: A new form of porous polyethylene, characterized by higher porosity and pore interconnectivity, was developed for use as a tissue-integrated implant. This study evaluated the effectiveness of porous polyethylene blocks used as an onlay bone graft in rabbit mandible in terms of tissue reaction, bone ingrowth, fibrovascularization, and graft-bone interfacial integrity. Methods: Twelve New Zealand white rabbits were randomized into 3 treatment groups according to the study period (4, 12, or 24 weeks). Cylindrical specimens measuring 5 mm in diameter and 4.5 mm in thickness were placed directly on the body of the mandible without bone bed decortication, fixed in place with a titanium screw, and covered with a collagen membrane. Histologic and histomorphometric analyses were done using hematoxylin and eosin-stained bone slices. Interfacial shear strength was tested to quantify graft-bone interfacial integrity. Results: The porous polyethylene graft was observed to integrate with the mandibular bone and exhibited tissue-bridge connections. At all postoperative time points, it was noted that the host tissues had grown deep into the pores of the porous polyethylene in the direction from the interface to the center of the graft. Both fibrovascular tissue and bone were found within the pores, but most bone ingrowth was observed at the graft-mandibular bone interface. Bone ingrowth depth and interfacial shear strength were in the range of 2.76-3.89 mm and 1.11-1.43 MPa, respectively. No significant differences among post-implantation time points were found for tissue ingrowth percentage and interfacial shear strength (P>0.05). Conclusions: Within the limits of the study, the present study revealed that the new porous polyethylene did not provoke any adverse systemic reactions. The material promoted fibrovascularization and displayed osteoconductive and osteogenic properties within and outside the contact interface. Stable interfacial integration between the graft and bone also took place.

• Composites Research
• /
• 제30권4호
• /
• pp.241-246
• /
• 2017

취성을 가진 섬유강화플라스틱은 충격을 받을 때 충격에너지를 흡수하면서 섬유와 기지재 간 계면에서 탈착 및 박리가 일어난다. 이는 복합재료의 에너지 충격흡수정도의 지표로 삼을 수 있다. 복합재료의 취성을 해결하기 위해 pine과 복합재료의 접착에 대한 연구가 되어 지고 있다. 이번 연구에서는 열처리 된 pine이 탄소섬유강화복합재료와 에폭시 접착제를 이용하여 접착되었다. 최적의 열처리 조건을 확인하기 위해, pine을 160도 및 200도 조건하에 열처리를 하였다. Pine 및 pine/탄소섬유복합재료의 기계적 및 계면물성을 파악하기 위해 인장, 인장중첩전단 및 아이조드 실험을 하였다. 또한, 열처리에 따른 나뭇결간의 결합력을 확인하기 위해 나뭇결 수직방향으로 인장시편 제조 후 파단될 때 탄성파를 음향방출시스템을 이용하여 분석하였다. 160도 조건으로 열처리 했을 때 나무강화 효과로 기계, 계면 및 나뭇결간의 결합력이 좋은 것을 확인하였다. 그러나 과한 열을 주게 되면 열에 약한 헤미셀룰로오스가 분해되면서 잡아주는 인자가 줄어들어 물성이 감소하였다.

• 한국결정성장학회지
• /
• 제24권4호
• /
• pp.151-157
• /
• 2014

The degradation mechanisms of thermal barrier coatings (TBCs) were investigated in different thermal fatigue condition in terms of microstructural analyses. The isothermal and cyclic oxidation tests were conducted to atmospheric plasma sprayed-TBCs on NIMONIC 263 substrates. The delamination occurred by the oxide layer formation at the interface, the Ni/Cr-based oxide was formed after Al-based oxide layer grew up to ${\sim}10{\mu}m$ in the isothermal condition. In the cyclic oxidation with dwell time, the failure occurred earlier (500 hr) than in the isothermal oxidation (900 hr) at same temperature. The thickness of Al-based oxide layer of the delaminated specimen in the cyclic condition was ${\sim}4{\mu}m$ and the interfacial cracks were observed. The acoustic emission method revealed that the cracks generated during the cooling step. It was considered that the specimens were prevented from the formation of the Al-based oxide by cooling treatment, and the degradation mode in the cyclic test was dominantly interfacial cracking by the difference of thermal expansion coefficients of the coating layers.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2000년도 춘계학술발표대회 논문집
• /
• pp.159-162
• /
• 2000

Interfacial and microfailure properties of carbon fiber/epoxy matrix composites were evaluated using both tensile fragmentation and compressive Broutman tests with acoustic emission (AE). Amino-silane and maleic anhydride polymeric coupling agents were used via the dipping and electrodeposition (ED), respectively. Both coupling agents exhibited higher improvements in interfacial shear strength (IFSS) under tensile tests than compressive cases. However, ED treatment showed higher IFSS improvement than dipping case under both tensile and compressive test. The typical microfailure modes including fiber break, matrix cracking, and interlayer failure were observed during tensile test, whereas the diagonal slippage in fiber ends was observed during compressive test. For both the untreated and treated cases AE distributions were separated well under tensile testing. On the other hand, AE distributions were rather closer under compressive tests because of the difference in failure energies between tensile and compressive loading. Under both loading conditions, fiber breaks occurred around just before and after yielding point. Maximum AE voltage fur the waveform of carbon or basalt fiber breakage under tensile tests exhibited much larger than those under compressive tests.

• 한국복합재료학회:학술대회논문집
• /
• 한국복합재료학회 2001년도 추계학술발표대회 논문집
• /
• pp.116-120
• /
• 2001

Fiber fracture is one of the dominant failure phenomena to determine total mechanical properties in composites. Fiber fracture locations were measured by optical microscopic method and acoustic emission (AE) as functions of matrix toughness and surface treatment by the electrodeposition (ED), and then two methods were compared. Two AE sensors were attached on the epoxy specimen and fiber fracture signals were detected with elapsed time. The interfacial shear stress (IFSS) was measured using tensile fragmentation test and AE system. In ED-treated case, the number of the fiber fracture measured by an optical method and AE was more than that of the untreated case. The signal number measured by AE were rather smaller than the number of fragments measured by optical method, since some fiber fracture signals were lost while AE detection. However, one-to-one correspondence between the x-position location by AE and real break positions by optical method was generally established well. The fiber break source location using AE can be a valuable method to measure IFSS for semi- or nontransparent matrix composites nondestructively (NDT).

• 한국세라믹학회지
• /
• 제33권7호
• /
• pp.823-831
• /
• 1996

Due to the intrinsic low surface activation of ${\gamma}$-alumina it has been used limitely in practice. Accordingly forward enhancing its utility ${\gamma}$-alumina surface was treated with slfuricf aicd nitric acid and chloric acid respec-tively. Subsequently the effects of surface activity on the surface electrical characteristics were investigated. The ${\gamma}$-alumina was prepared by the precipitation of aluminium nitrate [Al(NO3)3.9H2O] using ammonia water as a precipitator and it was chemically treated with such acids mentioned above. The surface and morphology of the acid-treated ${\gamma}$-alumina were analysed by XRD, BET and the surface activities were measured by the amine titration methods. The interfacial properties of the ${\gamma}$-alumina dispersed in electrolyte solution were esti-mated by the surface charge density measured using potentiometric tiration. Based on the relation between surface charge density and the acid amount the following results were drawn for the surface and interfacial electrical properties ; Acidic properties of surface-treated alumina increase with anion load on alumina surface. P. Z. C decreases with acid amount on alumina surface. The surface charge densities were apart from electrolyte ionic strength. The acidity of ${\gamma}$-alumina is linearly dependent on the P. Z,.C when the ${\gamma}$-alumina was dispersed in aqueous electrolyte solution.

• 한국주조공학회지
• /
• 제20권2호
• /
• pp.116-121
• /
• 2000

Interfacial reaction and mechanical properties between Sn-Zn-X ternary alloys(X : 3wt.%In, 4wt.%Bi) and Cu-substrate were studied. Cu/solder joints were subjected to aging treatments for up to 50days to see interfacial reaction at $100^{\circ}C$ and then were examined changes of microstructure and interfacial compound by optical microscopy, SEM and EDS. Cu/solder joints were aged to 30days and then loaded to failure at cross head speed of 0.3 mm $min^{-1}$ to measure tensile strength. According to the results of the solderability test, additions of In and Bi in the Sn-9wt.%Zn solder improve the wetting characteristics of the alloy and lower the melting temperature. Through the EDS and XRD analysis of Cu/Sn-9wt.%Zn solder joint, it was concluded that the intermetallic compound was the ${\gamma}-Cu_5Zn_8$ phase. Cu-Zn intermetallics at Cu/solder interfaces played an important role in both the microstructure evolution and failure of solder joints. Cu/solder joint strength was decreased by aging treatment, and those phenomenon was closely related to the thickening of intermetallic layer at Cu/solder joints.

• Korean Journal of Chemical Engineering
• /
• 제35권12호
• /
• pp.2487-2495
• /
• 2018

Inspired by the specific amino acid sequence Asn-Pro-Ala (NPA) of water channel aquaporins (AQPs), we fabricated polyamide (PA) nanofiltration (NF) membranes by introducing reduced glutathione (GSH) in interfacial polymerization (IP) method. Fourier transform infrared spectroscopy (ATR-FTIR), X-ray photoelectron spectrometry (XPS), scanning electron microscope (SEM), atomic force microscopy (AFM), zeta potential and static water contact angle measurement were employed to characterize the chemical composition, morphology, electronegativity and hydrophilicity of the NF membranes. The water flux of GSH/PIP-TMC NF membrane reached $32.00L\;m^{-2}h^{-1}$ at 0.2 MPa, which was approximately twice than that of pristine PIP-TMC NF membrane when the ratio of GHS to piperazidine (PIP) was 40% during IP process. More water channels were built as GSH was embedded into PA layer. The fabricated NF membranes also took on potent rejection for dyes and $Na_2SO_4$. This study presents a simple and facile method to simulate water channels-based biological materials which may find potential application in water treatment.