• 대한기계학회논문집B
• /
• 제27권12호
• /
• pp.1667-1672
• /
• 2003

In contrast to the high demand for MEMS devices, microflow analysis is not feasible even for single-phase flow with conventional Navier-Stokes equation because of non-continuum effect when characteristic dimension is comparable with local mean free path. DSMC is one of particle based DNS(Direct Numerical Simulation) methods that uses no continuum assumption. In this paper, gas flow in microchannel is studied using DSMC. Interfacial shear and flow characteristics are observed and compared with the results of gas flow that is in contact with liquid case and solid wall case. The simulation is limited to the case of equilibrium steady state and evaporation/condensation coefficient is assumed to be the same and unity. System temperature remains constant and the interfacial shear appears to be small compared to the result with solid wall. This is because particles evaporated and reflected from the liquid surface form high density layer near the interface with liquid flow.

• Nuclear Engineering and Technology
• /
• 제31권1호
• /
• pp.29-48
• /
• 1999

Local two-phase flow parameters of subcooled flow boiling in inclined annulus were measured to investigate the effect of inclination on the internal flow structure. Two-conductivity probe technique was applied to measure local gas phasic parameters, including void fraction, vapor bubble frequency, chord length, vapor bubble velocity and interfacial area concentration. Local liquid velocity was measured by Pilot tube. Experiments were conducted for three angles of inclination; 0$^{\circ}$(vertical), 30$^{\circ}$, 60$^{\circ}$. The system pressure was maintained at atmospheric pressure. The range of average void fraction was up to 10% and the average liquid superficial velocities were less than 1.3 m/sec. The results of experiments showed that the distributions of two-phase How parameters were influenced by the angle of channel inclination. Especially, the void fraction and chord length distributions were strongly affected by the increase of inclination angle, and flow pattern transition to slug flow was observed depending on the How conditions. The profiles of vapor velocity, liquid velocity and interfacial area concentration were found to be affected by the non-symmetric bubble size distribution in inclined channel. Using the measured distributions of local phasic parameters, an analysis for predicting average void fraction was performed based on the drift flux model and flowing volumetric concentration. And it was demonstrated that the average void fraction can be more appropriately presented in terms of flowing volumetric concentration.

• 한국원자력학회:학술대회논문집
• /
• 한국원자력학회 1999년도 춘계학술발표회요약집
• /
• pp.115-115
• /
• 1999

To demonstrate the applicability of RELAP5 to the prediction of the onset offlooding in the hot leg at the reflux condensation phase during mid-loop operation, numerical analysis is performed for the counter-current flow in a horizontal pipe with the inclined riser using the RELAP5/MOD3.2.2b code. It is found that the RELAP5, simulating the CCFL phenomena using interfacial friction along with the flow regime map in the horizontal pipe, produces unsatisfactory results. Under the CCFL condition, it is observed that large oscillation exists in the flow rate, void fraction, and etc. and the liquid flow rate is much lower than that predicted by the CCFL model measured in the experiment. The CCFL model of RELAP5 for the vertical volume is extended to the model for the horizontal and inclined volumes. The horizontal volume flow regime map and interfacial friction model coupled to the CCFL model are modified. And a new correlation developed from Kang's experiment is implemented to the CCFL model of RELAP5. With this modified RELAP5, the analysis of CCFL phenomena in the horizontal pipe and hot leg geometry is performed, and produces reasonable results in comparison with experimental data.

• Geomechanics and Engineering
• /
• 제11권3호
• /
• pp.345-359
• /
• 2016

In order to investigate the influence of the interfacial angel on failure characteristics and mechanism of combined coal-rock mass, 35 uniaxial/biaxial compressive simulation tests with 5 different interfacial angels of combined coal-rock samples were conducted by PFC2D software. The following conclusions are drawn: (1) The compressive strength and cohesion decrease with the increase of interfacial angle, which is defined as the angle between structure plane and the exterior normal of maximum principal plane, while the changes of elastic modulus and internal friction angle are not obvious; (2) The impact energy index $K_E$ decreases with the increase of interfacial angle, and the slip failure of the interface can be predicted based on whether the number of acoustic emission (AE) hits has multiple peaks or not; (3) There are four typical failure patterns for combined coal-rock samples including I (V-shaped shear failure of coal), II (single-fracture shear failure of coal), III (shear failure of rock and coal), and IV (slip rupture of interface); and (4) A positive correlation between interfacial angle and interface effect is shown obviously, and the interfacial angle can be divided into weak-influencing scope ($0-15^{\circ}$), moderate-influencing scope ($15-45^{\circ}$), and strong-influencing scope (> $45^{\circ}$), respectively. However, the confining pressure has a certain constraint effect on the interface effect.

• 접착 및 계면
• /
• 제5권4호
• /
• pp.9-16
• /
• 2004

견섬유와 폴리라틱산(PLA) 사이의 계면접착 특성을 향상시키기 위하여 천연섬유 표면을 아르곤과 에틸렌 플라즈마로 각각 처리하였다. 플라즈마 표면처리 후, 견섬유의 표면 모폴로지와 접착이 크게 변화하였다. 다음의 여러 플라즈마 처리조건이 본 연구에 사용되었다: 10, 25, 50 그리고 150 W의 전력, 1, 3, 5, 7 그리고 10분의 처리시간 및 10과 50 sccm의 가스흐름속도, 플라즈마 처리된 Silk/PLA 바이오복합재료의 계면전단강도는 단섬유 micro-droplet debonding 시험방법으로 측정하였다. 결과는 Silk/PLA 바이오복합재료의 계면접착을 향상시키기 위한 최적의 플라즈마 처리 조건을 제공하여 주었다.

• Korean Chemical Engineering Research
• /
• 제53권3호
• /
• pp.315-320
• /
• 2015

Characteristics of gas-liquid mass transfer and interfacial area were investigated in a bubble column of diameter and height of 0.102 m and 2.5 m, respectively. Effects of gas and liquid velocities on the volumetric gas-liquid mass transfer coefficient ($k_La$), interfacial area (a) and liquid side true mass transfer coefficient ($k_L$) were examined. The interfacial area and volumetric gas-liquid mass transfer coefficient were determined directly by adopting the simultaneous physical desorption of $O_2$ and chemical absorption of $CO_2$ in the column. The values of $k_La$ and a increased with increasing gas velocity but decreased with increasing liquid velocity in the bubble column which was operated in the churn turbulent flow regime. The value of $k_L$ increased with increasing gas velocity but did not change considerably with increasing liquid velocity. The liquid side mass transfer was found to be related closely to the liquid circulation as well as the effective contacting frequency between the bubbles and liquid phases.

• 대한기계학회논문집B
• /
• 제39권8호
• /
• pp.677-682
• /
• 2015

격자 볼츠만 기법(Lattice Boltzmann method)을 사용하여 에멀전의 유변학적 특성을 파악하기 위한 시뮬레이션을 수행하였다. 간단한 전단 유동하에서 온도와 전단속도, 계면장력에 변화를 주어 에멀전(decane-in-water)의 상대점도를 계산하고 이를 분석하였다. 에멀전의 상대점도는 온도가 증가함에 따라 감소하였고, 전단속도가 증가함에 따라 감소하는 전단박하(Shear thinning) 현상을 보여주었다. 이는 크로스 모델(Cross model)을 통해 검증하였고 일치하는 경향을 보여주었다. 계면에 존재하는 계면활성제(Surfactant)를 통해 제어되는 계면장력이 증가할수록 상대점도는 감소하는 경향을 보여주었다. 이것은 큰 계면장력에서는 기름방울의 변형이 억제되고 점도가 상대적으로 높은 기름방울의 표면적이 감소하면서 나타난다고 해석할 수 있다.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2003년도 추계학술대회
• /
• pp.706-711
• /
• 2003

A numerical method is presented for computing unsteady incompressible two-phase flows with immersed solids. The method is based on a level set technique for capturing the phase interface, which is modified to satisfy a contact angle condition at the solid-fluid interface as well as to achieve mass conservation during the whole calculation procedure. The modified level set method is applied for numerical simulation of bubble deformation in a micro channel with a cylindrical solid block and liquid jet from a micro nozzle.

• 대한기계학회논문집
• /
• 제12권3호
• /
• pp.599-606
• /
• 1988

본 연구에서는 공기와 물을 사용한 근사수평 반류성층유동에서의 계면파 구조 를 측정하였다. 3차원파 영역내의 유동조건하에서 탐침접촉법을 이용하여 계면파의 액막분포도를 구하였으며 Gauss 모델과 비교분석하였다. 또 이 분포도에서 파의 구 조와 관련된 통계치, 즉 평균액막두께, 파진폭, 파고 교란강도등을 계산하여 유동조건 에 따른 경향을 분석하였다. 본 연구와 병행하여 계면전단응력과 계면마찰계수에 관 한 실험을 수행하였는데 이 결과와 계면파 구조와의 상호연관성도 고찰하였다.

• Membrane and Water Treatment
• /
• 제15권1호
• /
• pp.31-39
• /
• 2024

The flow in a nanopore of filtration membrane is often multiscale and consists of both the adsorbed layer flow and the intermediate continuum fluid flow. There is a controversy on which interface the slippage should occur in the nanopore filtration: On the adsorbed layer-pore wall interface or on the adsorbed layer-continuum fluid interface? What is the difference between these two slippage effects? We address these subjects in the present study by using the multiscale flow equations incorporating the slippage on different interfaces. Based on the limiting shear strength model for the slippage, it was found from the calculation results that for the hydrophobic pore wall the slippage surely occurs on the adsorbed layer-pore wall interface, however for the hydrophilic pore wall, the slippage can occur on either of the two interfaces, dependent on the competition between the interfacial shear strength on the adsorbed layer-pore wall interface and that on the adsorbed layer-continuum fluid interface. Since the slippage on the adsorbed layer-pore wall interface can be designed while that on the adsorbed layer-continuum fluid interface can not, the former slippage can result in the flux through the nanopore much higher than the latter slippage by designing a highly hydrophobic pore wall surface. The obtained results are of significant interest to the design and application of the interfacial slippage in nanoporous filtration membranes for both improving the flux and conserving the energy cost.