• 한국소음진동공학회:학술대회논문집
• /
• 한국소음진동공학회 2006년도 춘계학술대회논문집
• /
• pp.660-665
• /
• 2006

This paper presents a finite element method to analyze the free and forced vibration of a hard disk drive (HDD) considering the flexibility of a spinning disk-spindle with fluid dynamic bearings (FDBs), an actuator with pivot bearings, an air bearing between head-disk interface and the base with complicated geometry. Finite element equation of each component is consistently derived with the satisfaction of the geometric compatibility of the internal boundary between each component. The spinning disk, hub and FDBs are modeled by annular sector elements, beam elements and stiffness and damping elements, respectively. The actuator am, E-block, suspension and base plate are modeled by tetrahedral elements. The pivot bearing in the actuator and the air bearing between head-disk interfaces are modeled by the stiffness element with five degrees of freedom and the axial stiffness, respectively. A global matrix equation obtained by assembling the finite element equations of each substructure is transformed to a state-space matrix-vector equation, and both damped natural frequencies and modal damping ratios are calculated by solving the associated eigenvalue problem with the restarted Arnoldi iteration method. Modal and shock testing are performed to show that the proposed method well predicts the vibration characteristics of a HDD.

• 마이크로전자및패키징학회지
• /
• 제25권4호
• /
• pp.111-118
• /
• 2018

강성도가 서로 다른 두 polydimethylsiloxane (PDMS) 탄성고분자와 flexible printed circuit board (FPCB)로 이루어진 soft PDMS/hard PDMS/FPCB 구조의 강성도 국부변환 신축기판을 개발하기 위해 PDMS와 FPCB를 acrylic-silicone 양면테이프를 사용하여 접합한 후 접합공정에 따른 PDMS/FPCB 계면접착력을 분석하였다. 완전 경화된 PDMS에 acrylic-silicone 양면테이프의 silicone 접착제로 접착한 FPCB의 pull 강도는 259 kPa이었으며, pull 시험시 PDMS와 silicone 접착제 사이에서 박리가 발생하였다. 반면에 $60^{\circ}C$에서 15~20분 유지하여 반경화시킨 PDMS에 acrylic-silicone 양면테이프의 silicone 접착제로 FPCB를 접착 후 $60^{\circ}C$에서 12시간 유지하여 PDMS를 완전 경화시키면 pull 강도가 1,007~1,094 kPa로 크게 향상되었으며, pull 시험시 계면 박리가 acrylic-silicone 양면테이프의 acrylic 접착제와 FPCB 사이에서 발생하였다.

• Structural Engineering and Mechanics
• /
• 제16권6호
• /
• pp.749-769
• /
• 2003

The structural deterioration of concrete structures due to reinforcement corrosion is a major worldwide problem. Service life of the age-degraded concrete structures is governed by the protective action provided by the cover concrete against the susceptibility of the reinforcement to the corrosive environment. The corrosion of steel would result in the various corrosion products, which depending on the level of the oxidation may have much greater volume than the original iron that gets consumed by the process of corrosion. This volume expansion would be responsible for exerting the expansive radial pressure at the steel-concrete interface resulting in the development of hoop tensile stresses in the surrounding cover concrete. Once the maximum hoop tensile stress exceeds the tensile strength of the concrete, cracking of cover concrete would take place. The cracking begins at the steel-concrete interface and propagates outwards and eventually resulting in the through cracking of the cover concrete. The cover cracking would indicate the loss of the service life for the corrosion-affected structures. In the present paper, analytical models have been developed considering the residual strength of the cracked concrete and the stiffness provided by the combination of the reinforcement and expansive corrosion products. The problem is modeled as a boundary value problem and the governing equations are expressed in terms of the radial displacement. The analytical solutions are presented considering a simple 2-zone model for the cover concrete viz. cracked or uncracked. A sensitivity analysis has also been carried out to show the influence of the various parameters of the proposed models. The time to cover cracking is found to be function of initial material properties of the cover concrete and reinforcement plus corrosion products combine, type of rust products, rate of corrosion and the residual strength of the cover concrete. The calculated cracking times are correlated against the published experimental and analytical reference data.

• Composites Research
• /
• 제30권4호
• /
• pp.247-253
• /
• 2017

본 연구에서는 분자동역학 전산모사와 이중 입자 모델을 이용하여 질화붕소 나노튜브-폴리메틸메타크릴레이트 나노복합재의 기계적 물성과 계면특성을 규명하였다. 단일 벽 나노튜브가 고분자 기지에 함침된 가로등방성 나노복합재 단위 셀 구조를 모델링한 후, 각 방향으로의 일축인장 및 전단 전산모사를 통해 나노복합재의 강성행렬을 예측하였다. 또한 강성행렬의 방향 평균을 취해 나노튜브가 기지 내에 랜덤 분포하는 경우의 등방성 탄성계수를 도출하였다. 분자동역학 해석 결과를 계면의 완전 결합을 가정한 이중 입자 모델 예측해와 비교한 결과, 질화붕소 나노튜브와 고분자 기지간의 계면이 불완전한 것으로 확인되었다. 나노튜브 주위에 형성되는 흡착계면의 물성을 예측하기 위해 2단계 영역 분할 기법을 도입하였고 계면의 불완전 결합을 선형 스프링으로 묘사하였다. 그 결과 다양한 스프링 컴플라이언스 값에 따른 흡착계면의 물성을 역 해석을 통해 확인할 수 있었다.

• 비파괴검사학회지
• /
• 제32권4호
• /
• pp.376-387
• /
• 2012

비선형 스프링 모델과 섭동법을 기초로 비선형 균열면에 경사 입사된 초음파에 의해 발생되는 2차 고조파 초음파의 크기를 계산하였다. 비선형 균열계면에서 만들어지는 반사파와 굴절파의 기본주파수 성분과 2차 고조파 성분의 크기를 입사각과 균열계면의 계면강성을 변화키면서 조사하였다. 계면강성에 관계없이 균열계면이 초음파 진행 방향과 비슷한 경우 반사와 굴절파 모두에서 2차 고조파의 발생은 거의 없었지만, 그렇지 않은 경우에는 계면 입사각은 물론 계면 강성에 따라 2차 고조파의 크기는 크게 변화하였다. 투과파는 물론 반사파에서도 2차 고조파 성분이 유의성 있게 발생됨을 수치 해석을 통해 확인하였다.

• Structural Engineering and Mechanics
• /
• 제21권6호
• /
• pp.659-676
• /
• 2005

The novel form of composite walling system consists of two skins of profiled steel sheeting with an in-fill of concrete. The behaviour of such walling under in-plane shear is important in order to utilise this system as shear elements in a steel framed building. Steel sheet-concrete interface governs composite action, overall behaviour and failure modes of such walls. This paper describes the finite element (FE) modelling of the shear behaviour of walls with particular emphasis on the simulation of steel-concrete interface. The modelling of complex non-linear steel-concrete interaction in composite walls is conducted by using different FE models. Four FE models are developed and characterized by their approaches to simulate steel-concrete interface behaviour allowing either full or partial composite action. Non-linear interface or joint elements are introduced between steel and concrete to simulate partial composite action that allows steel-concrete in-plane slip or out of plane separation. The properties of such interface/joint elements are optimised through extensive parametric FE analysis using experimental results to achieve reliable and accurate simulation of actual steel-concrete interaction in a wall. The performance of developed FE models is validated through small-scale model tests. FE models are found to simulate strength, stiffness and strain characteristics reasonably well. The performance of a model with joint elements connecting steel and concrete layers is found better than full composite (without interface or joint elements) and other models with interface elements. The proposed FE model can be used to simulate the shear behaviour of composite walls in practical situation.

• 한국항공우주학회지
• /
• 제33권11호
• /
• pp.7-14
• /
• 2005

접촉 현상을 포함하는 완전 연계된 열기계학적 문제에 대한 정확하고 효율적인 해석을 위하여 부영역과 공유면에 근거한 유한요소 정식화 기법을 제안하였다. 부영역과 공유면을 결합하기 위한 등식 적합 조건을 벌칙 함수로 처리함으로써 모든 유효 강성 행렬이 양정치화되며, 역행렬과 같은 각종 수치 연산이 매우 간편하다. 또한 전체 구조 형상이 복잡하더라도 대상 영역을 임의의 부영역으로 분할한 후, 공유면에서의 절점 연속성 등을 고려하지 않고 각 부영역을 독립적으로 유한요소 모델링할 수 있다. 컴퓨터 코드의 개발 및 수치 예제의 해석을 통하여 본 기법에 대한 기본적인 특성을 확인하였다.

• 한국항공우주학회지
• /
• 제35권5호
• /
• pp.404-411
• /
• 2007

접촉 문제의 효율적인 유한요소 해석을 위하여 부영역, 공유면 및 접촉 공유면의 개념에 근거한 영역/경계 분할법을 제시하였다. 부영역과 공유면 또는 접촉 공유면을 결합하기 위한 등식 적합 조건을 벌칙 함수로 처리함으로써 모든 유효 강성 행렬이 양 정치화되므로, 역행렬과 같은 각종 행렬의 연산이 매우 간편해진다. 또한 전체 영역 형상이 복잡하더라도, 임의의 부영역으로 분할한 후 공유면에서의 절점 연속성을 고려하지 않고 각각의 부영역을 독립적으로 이산화할 수 있다. 간단한 수치 예제 해석을 통하여 본 기법의 기본적인 특성을 고찰하였다.

• Restorative Dentistry and Endodontics
• /
• 제23권2호
• /
• pp.639-646
• /
• 1998

To evaluate the effect of interface conditions and retention grooves in the Class V composite resin restoration of the maxillary first premolar, the distribution of the values of stress and displacement was analyzed with the two-dimensional finite element method. The results were obtained as follows : 1. Boundary elements and Stiffness values could be used as the interface parameters in the, finite element method. 2. The amount of restriction of the displacement at the cervical margin by placing a retention groove at the cervical wall was about three times as high as that by placing a retention groove at the occlusal wall. 3. Because of the relative amount of tensile components of the stress values in the bucco-lingual direction, the possibility of dislocation of the restoration was much higher at the cervical margin than at the occlusal margin. 4. It might be recommended that both occlusal and cervical retention grooves be used routinely, but if one, it be placed at the cervical wall.

• Structural Engineering and Mechanics
• /
• 제64권5호
• /
• pp.543-555
• /
• 2017

The non-linear behaviour of integral infilled frames (in which the infill and the frame are bonded together with help of various interface materials) is studied both experimentally and numerically. The experiments were carried out on one-sixth scale two-bay and three-storey reinforced concrete frames with and without infill against static cyclic loading. Three interface materials - cement mortar, cork and foam have been used in between the infill and the frame. The infill, interface and the frame are bonded together is called integral frame. The linear and non-linear behaviors of two dimensional bare frame and integral infilled frame have been studied numerically using the commercial finite element software SAP 2000. Linear finite element analysis has been carried out to quantify the effect of various interface materials on the infilled frames with various combinations of 21 cases and the results compared. The modified configuration that used all three interface materials offered better resistance above others. Therefore, the experiments were limited to this modified infilled frame case configuration, in addition to conventional (A1-integral infilled frame with cement mortar as interface) and bare frame (A0-No infill). The results have been compared with the numerical results done initially. It is found that stiffness of bare frame increased by infilling and the strength of modified frame increased by 20% compare to bare frame. The ductility ratio of modified infilled frame was 42% more than that of the conventional infilled frame. In general, the numerical result was found to be in good agreement with experimental results for initial crack load, ultimate load and deformed pattern of infill.