• Journal of the Korean Institute of Illuminating and Electrical Installation Engineers
• /
• v.18 no.2
• /
• pp.115-124
• /
• 2004

This paper suggested the vibration characteristic improvement by variation mode of ring type ultrasonic motor. Design for the piezoelectric ceramic and elastic body of stator were calculated by the finite element method(FEM) that consider the resonance frequency, vibration mode and coupling efficiency etc. Through the result of vibration analysis from 6 order mode to 8 mode, the 7 order mode was gained very an excellent results that it was the coupling efficient, minimum power loss and bending vibration value. Here over 7 order mode, was acquired that an output current for input voltage was very a large increased results. The result of vibration calculation, from thickness 0.5[mm] to 2[mm], know the fact that the vibration displacement at 0.5[mm] is an high value too. From such analysis result, this paper was manufactured the ultrasonic motor of outer diameter 50[mm], inter 22[mm] having the about 43.86[KHz] resonance frequency. We have gated that a simulation result is 42.2[KHz] and an experiment result is 43.86[KHz]. Then, a propriety of this paper was established the result almost similar to though comparison, investigation of simulation and experiment result.

• Proceedings of the Korean Society of Propulsion Engineers Conference
• /
• v.y2005m4
• /
• pp.219-224
• /
• 2005

In order to investigate transient behaviour of the CRW(Canard Rotor Wing) type UAV(Uninhabited Aerial Vehicle) propulsion system during flight mode transition considering flow control valve operation, the propulsion system was modelled using SIMULINK commercial program. For transient simulation of the main engine system, the ICV(Inter-Component Volume) method was applied. The valve system is to control the gas flow of the rotary duct system and the main duct system, and the analysis was performed with an assumption that the total gas mass flow of the main engine is the same as summation of the rotary duct flow and the main duct flow, and with consideration of valve loss, flow rate and effective area in valve angle variation. The performance analysis was carried out during flight mode transitions from the rotary flight mode to the fixed wing flight mode and vice versa mode at altitude of 1Km, flight Mach number 0.1 and maximum engine rpm.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.35 no.2C
• /
• pp.193-202
• /
• 2010

In this paper, we propose a fast algorithm that can reduce the complexity for inter mode decision of the H.264 encoder. The main idea consists of two techniques. The first one is the technique early terminating mode decision process. We focused on the skip and $16{\times}16$ mode because these modes occupies the largest portion in most of sequences. The second one is the technique skipping unnecessary $8{\times}8$ modes. The time consumption caused by the $8{\times}8$ mode is very considerable. Therefore if we can extract the unnecessary $8{\times}8$ mode calculation well, a large amount of time can be saved in total encoding process. The experimental results show that the proposed algorithm can achieve up to 43% speed up ratio with insignificant PSNR loss. The increase of total bits encoded is also not noticeable.

• Journal of Broadcast Engineering
• /
• v.10 no.3
• /
• pp.321-327
• /
• 2005

A MVC (Multi-view Video Coding) method, which uses both an illumination change-adaptive ME (Motion Estimation)/DC (Motion Compensation) and a 2D (Dimensional) direct mode, is proposed. Firstly, a new SAD (Sum of Absolute Difference) measure for ME/MC is proposed to compensate the Luma pixel value changes for spatio-temporal motion vector prediction. Illumination change-adaptive (ICA) ME/MC uses the new SAD to improve both MV (Motion Vector) accuracy and bit saving. Secondly, The proposed 2D direct mode that can be used in inter-view prediction is an extended version of the temporal direct mode in MPEG-4 AVC. The proposed MVC method obtains approximately 0.8dB PSNR (Peak Signal-to-Noise Ratio) increment compared with the MPEG-4 AVC simulcast coding.

• Journal of Broadcast Engineering
• /
• v.13 no.2
• /
• pp.200-213
• /
• 2008

H.264| MPEG-4 AVC is a new video codingstandard defined by JVT (Joint Video Team) which consists of ITU-T and ISO/IEC. Many techniques are adopted fur the compression efficiency: Especially, an intra prediction in an inter frame is one example but it leads to excessive amount of encoding time due to the decision of a candidate mode and a RDcost calculation. For this reason, a fast determination of the best intra prediction mode is the main issue for saving the encoding time. In this paper, by using the result of statistical relation between intra $16{\times}16$ and $4{\times}4$ intra predictions, the number of candidate modes for $4{\times}4$ intra prediction is reduced. Firstly, utilizing motion vector obtained after inter prediction, prediction of a block mode for each macroblock is made. If an intra prediction is needed, the correlation table between $16{\times}16$ and $4{\times}4$ intra predicted modes is created using the probability during each I frame-coding process. Secondly, using this result, the candidate modes for a $4{\times}4$ intra prediction that reaches a predefined specific probability value are only considered in the same GOP For the experiments, JM11.0, the reference software of H.264|MPEG-4 AVC is used and the experimental results show that the encoding time could be reduced by 51.24% in maximum with negligible amounts of PSNR drop and bitrate increase.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.23 no.9
• /
• pp.1034-1041
• /
• 2012

In this paper, a compact circularly polarized metamaterial patch antenna using the -1 mode that is induced by the composit right-left handed(CRLH) transmission line is proposed. Basically, since the -1 mode is the same properties with the +1 mode of the conventional patch antenna, the circular polarization(CP) is realized. If two orthogonal -1 modes are excited with $90^{\circ}$ phase difference, the CP property can be obtained. In order to obtain two orthogonal modes and $90^{\circ}$ phase difference, 4 mushroom structures having the shape of triangle are employed and the inter-digital gaps are optimized, respectively. The fabricated antenna is based on RT/duroid5880 substrate and the total area of the 4 mushrooms is $0.161{\lambda}_0{\times}0.161{\lambda}_0$. It is confirmed that the center frequency of the proposed antenna is measured as 2.845 GHz and it operates from 2.830 GHz to 2.850 GHz. In addition, the antenna maintains the CP property from 2.842 GHz to 2.847 GHz at the peak gain and the measured radiation efficiency is 46 %.

• The Journal of Korean Institute of Communications and Information Sciences
• /
• v.25 no.1B
• /
• pp.77-88
• /
• 2000

This paper presents an approach for rate control by adaptively selecting macroblock modes in video coding.The problem of rate control has been investigated by many authors where quantizer level is adjustedbased on the buffer fullness. The proposed approach is different fron the previous ones [4] id that it finds the optimal decision curve rather than finding a set of the modes. Proposed algorithm extends the coding decision options for rate control to motion/no-motion compensation as well as inter/intra decisions. Instead of having a fixed motion/no-notion compensation or inter/intra decision curve, one can utilize an adaptive decision curvebased on the characteristics of input frames so that the PSNR at a given bit rate is maximized. Therefore, the proposed approach provides better rate control than simple quantizer feedback approach interns of visual quality. The curve is obtained by utilizing simulated annealing optimization technique. Thealgorithm is implemented and simulations are compared with other approaches within H.261 video codec.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2004.08a
• /
• pp.1220-1222
• /
• 2004

We developed a new device structure using anisotropic phase separation from liquid crystal (LC) and polymer composite materials using UV intensity variation and polymer wetting properties. In the device, the LC molecules are isolated in pixels where LCs are surrounded by the inter-pixel vertical polymer walls and the horizontal polymer films on the upper substrate. These devices show very good mechanical stability against external pressure. The electro-optic characteristics and the mechanical stability of the devices are discussed in view of the flexible display applications.

• Journal of the Korean Society for Railway
• /
• v.4 no.2
• /
• pp.13-18
• /
• 2001

외국에서는 정보통신 기술에 의하여 주도되는 차세대 철도의 개념(concept)을 만드는 검토작업이 진행되고 있다. 이 개념을 사이버 철도(cybernetics rail)라고 칭하며, 그 검토에서는 "복수의 모드(mode)가 유기적으로 제휴한 인터 모들(inter-modal) 수송의 중핵을 철도가 담당하기 위해서는 무엇이 필요한가'를 중심 명제로서 의식하고 있다. 이 글에서는 "인터 모들'과 "이용자 요구(demand)"를 키워드로 하여 외국에서 진행되고 있는 사이버 철도의 검토 내용을 소개한다. (중략)도의 검토 내용을 소개한다. (중략)

• Proceedings of the Korean Information Science Society Conference
• /
• 2008.06a
• /
• pp.241-242
• /
• 2008