In this paper the analysis of laminate composite folded plates with arbitrary angle connection like box girder is studied by finite strip method Total stiffness of laminated plate is obtained by integration of the stiffness in each layer or lamina through laminate thickness and total stiffness in each layer or lamina through laminate thickness and total tiffness matrix is obtained by substitutionto equilibrium equation derived from the minimum total potential energy theorem. The assumed displacement functions for a finite strip method in plate or box girder analysis are combinations of one-way polynomial functions in the transverse direction and harmonic functions in the span-wise direction. Finite strip method with the merits of the simplification in modeling and the reduction of analytical time is accurate in the analysis of laminate composite folded plates shaped like box firders.
This paper includes the test results of KOMPSAT-2 payload downlink system which
were measured for the purpose of performance verification. The antenna beam patterns
which indicates the status of the interface & antenna itself, were measured as well as
the antenna VSWR. The checkout of the transponder & its spectrum was followed and
this made sure that there was no spurious output distinguished. Finally a test for BER
verification was conducted between satellite and receiving system for their compatibility
through the antenna-to-antenna connection using an antenna hat. Verification tests for
an RF system should be performed after relocation, integration and test for
environments in order to make sure that no degradation happens.
In order to promote the practicality of high-rise steel buildings, the development of structural system which have the better fire resistance, the changeable plan, and the quality control of construction with general composite beams is needed. In this research, new semi-slim floor which the defect of general slim floor was complemented was evaluated to investigate the concrete integration with slim-flor beam and the flexural performance. 5 simply supported semi-slim floor beam tests were performed with parameters; structural form of slab support beam, slab thickness, with or without web opening, and shear connection. Experimental results showed that all specimen s had good ductile behavior.
This study was to focus on analyzing about the composition of storytelling in the first graders' math textbooks of the middle school, which were recently implemented. The textbooks published by three well known publishing companies were chosen and three graduate students had scored the frequency of the problems according to three types of storytelling. As the results, in areas of mathematics, Number & Operation(44.23%), Letters & Formula(44.53%), Function(46.53%), Probability(41.67%), Geometry(46.23%) showed to have storytelling in balance. The type of 'explosion of mathematical history(EMH)' was shown in geometry most, the type of 'connection to daily life(CDL)' in statistics most, and the type of integration of disciplines(ID)' in geometry most in 5 math areas. Among three types of storytelling, the type of EMH was shown fewer that other 2 types. If we develop more problems in this type, students would study mathematics in-depth according to Freudenthal's principle of historical reinvention.
During last five years several workshops and seminars among social work educators, in and out country, has taken place. In those gatherings there has been, criticism on American model on which curriculum of social work in Korea has mainly based, and many proposals which most developing countries should consider and adopt for developing their own curriculums. The proposals could be summarized as follows; 1. Specification of developmental functions of social work should be made so that the curriculum could involve. It also must come from own societal needs and own national development task. 2. Social work should participate and make contribution to plan and solve the main social problems in own countries. 3. Clarification of educational objective in undergraduate level should be made and one of them must be related to the first professional degree. 4. There should be the courses which provide the content of macro level participation. How much of the proposals are reflected in the current curriculum of Korea? What are the problems Korean social work education has been faced in connection with reflecting the proposals? What kinds of task we should or could perform in order to adopt the proposals? These are the questions which deserved to be studied. The followings are the answers to the questions; 1. The new courses such as social welfare policy and planning, Social Development, Population Dynamics and Family Planning, Social problems, Special Issues in Social Welfare, etc, are placed in the curriculum. 2. Though the new courses are added the courses of case work, group work, and community organization are strongly remained it means that integrative method is not quite adopted and that conflicts are taking place between new and old fashion. 3. Fieldwork placement policy has been changes from concurrent to block and from social work method oriented to social problem oriented. 4. There are lack of integration among the all courses, of consistency between pre and post courses and connection among the related courses. 5. Establishment of image of social worker with B, A. degree should be urgently taken place. It can't be done by social work field alone but by cooperation with all the forces related to the social work practice. 6. B. A. graduate should have a common base of knowledge and competence. It could be come from the clear and specified objectives of undergraduate level education. And agreement among the member schools on the objectives can call on the fundamental similarities in each curriculums. Different programs from one school to another can be tolerated as long as there are fundamental similarities among the schools. Basic concepts and framework of social work should be kept clearly. It is a slow and long process to make social work recognized as a profession in the developing countries. Korea can't be and exception. Failure of having social work be indegenous can't be the reason to refuse an change the basic concepts of social work. One of he most important task which social work education in Korea must achieve in the near future is to establish the minimum requirement courses in the curriculum. Social work field, on the other hand, must find the positions for the social works in the various settings and institute. Clear role and image of social worker can be obtained by doing that.
Park Chan-Jin;Kim Yung-Soo;Kim Chang-Whe;Cho Lee-Ra;Yi Yang-Jin
The Journal of Korean Academy of Prosthodontics
/
v.41
no.3
/
pp.271-287
/
2003
Statement of problem: Resonance frequency analysis (RFA) has been increasingly served as a non-invasive and objective method for clinical monitoring of implant stability. Many clinical studies must be required for standardized baseline data using RFA. Purpose: This study was performed to evaluate RFA value changes in two stage surgery group and one stage surgery group in patients. Material and method: Forty-seven mandibles in consecutively implant installed patients were selected for this study and 141 fixtures were installed. Ninety-three fixtures were double threaded, machined surface design ($Br{\aa}anemark^{(R)}$ MK III, Nobel Biocare AB, Goteborg, Sweden) and 48 fixtures were root form, threaded, HA-coated surface one ($Replace^{TM}$, Steri-Oss/Nobel Biocare AB, USA). Among those, each 10 fixture was installed in one stage group patients. ISQ values were measured using $Osstell^{TM}$ (Integration Diagnostics Ltd. Sweden) during fixture installation, at healing abutment connection and in the loading period for two stage surgery group patients and during at each 4, 6, 8, 10, 12week and in the loading phase for one stage surgery group patients and evaluated the changes according to the time and fixture type. Results: In two stage surgery group, mean and SO of ISQ values of machined surface implants were $76.85{\pm}3.74,\;75.76{\pm}5.04,\;75.73{\pm}4.41$ and those of HA-coated surface implant were $75.05{\pm}6.23,\;77.58{\pm}5.23,\;78.32{\pm}4.29$ during fixtures installation, at healing abutment connection and in the loading period, respectively. In one-stage surgery group, the ISQ values of machined surface and HA-coated surface implants decreased until 4 or 6 week and maintained at plateau for 1-3 week and increased to the loading period. Conclusions: Machined and HA-coated surface implants showed minimal ISQ changes with time if they were installed at the sites showing at least intact cortical plate and good bone qualities. And HA-coated implants had a tendency to show somewhat increased ISQ values with time.
Park, Hyun-Soo;Lim, Sung-Bin;Chung, Chin-Hyung;Hong, Ki-Seok
Journal of Periodontal and Implant Science
/
v.36
no.2
/
pp.531-554
/
2006
Oral implants must fulfill certain criteria arising from special demands of function, which include biocompatibility, adequate mechanical strength, optimum soft and hard tissue integration, and transmission of functional forces to bone within physiological limits. And one of the critical elements influencing the long-term uncompromise functioning of oral implants is load distribution at the implant- bone interface, Factors that affect the load transfer at the bone-implant interface include the type of loading, material properties of the implant and prosthesis, implant geometry, surface structure, quality and quantity of the surrounding bone, and nature of the bone-implant interface. To understand the biomechanical behavior of dental implants, validation of stress and strain measurements is required. The finite element analysis (FEA) has been applied to the dental implant field to predict stress distribution patterns in the implant-bone interface by comparison of various implant designs. This method offers the advantage of solving complex structural problems by dividing them into smaller and simpler interrelated sections by using mathematical techniques. The purpose of this study was to evaluate the stresses induced around the implants in bone using FEA, A 3D FEA computer software (SOLIDWORKS 2004, DASSO SYSTEM, France) was used for the analysis of clinical simulations. Two types (external and internal) of implants of 4.1 mm diameter, 12.0 mm length were buried in 4 types of bone modeled. Vertical and oblique forces of lOON were applied on the center of the abutment, and the values of von Mises equivalent stress at the implant-bone interface were computed. The results showed that von Mises stresses at the marginal. bone were higher under oblique load than under vertical load, and the stresses were higher at the lingual marginal bone than at the buccal marginal bone under oblique load. Under vertical and oblique load, the stress in type I, II, III bone was found to be the highest at the marginal bone and the lowest at the bone around apical portions of implant. Higher stresses occurred at the top of the crestal region and lower stresses occurred near the tip of the implant with greater thickness of the cortical shell while high stresses surrounded the fixture apex for type N. The stresses in the crestal region were higher in Model 2 than in Model 1, the stresses near the tip of the implant were higher in Model 1 than Model 2, and Model 2 showed more effective stress distribution than Model.
Journal of the Korean association of regional geographers
/
v.17
no.6
/
pp.698-709
/
2011
Wedding shops, which had been located in Jung-gu, Jongno-gu, Seodaemun-gu, and Mapo-gu in 1990, have been shown a rapid change in light of location since the year of 1995. Thus, most of shops are concentrated on Gangnam-gu in 2010. Wedding dress shops in Gangnam-gu were distributed between Kanglim Church and Apgujeong station in the early 1990s, and then moved gradually to Dosan park and then to Cheongdam-dong after passing through Hakdong intersection. Luxury image in Cheongdam-dong was the main reason for integration of wedding businesses. This intergration of shops showed the peak at the Cheongdam intersection. A motive of having come to start business in Cheongdam-dong was selected the high awareness and image in district, and was taken the ease for business-based cooperation and connection. High rent and inconvenient transportation were reasons for dissatisfaction. The business-based cooperation and connection were mostly formed through a consulting company. Level and reputation of relevant shops were important elements. Even the connective and associative shops are located the most in Cheongdam-dong followed by Nonhyeon-dong, Shinsa Apgujeong-dong in order. The cluster relationship was most noticeable in wedding studio, wedding dress, wedding consulting, and hanbok(Korean traditional clothes) business. Frequency of vertical cluster was indicated to be more than horizontal cluster. User behavior of wedding businesses in Seoul has been collecting wedding information through internet and wedding consulting business.
The mammalian ovary is innervated by sympathetic and sensory neurons which contribute to regulating several aspects of ovarian function, including blood flow, steroidogenesis and follicular development. The existence of a neural connection between central neurons and the ovary has been rarely reported, but the mechanism underlying integration of ovarian activity to broader neuroendocrine responses has not been reported. We have now used a viral transneuronal tracing technique combined with a conventional retrograde labeling procedure of CT-HRP to demonstrate that oxytocin-producing neurons of the hypothalamus are synaptically connected to the ovary. Since ovarian activity is suppressed but the activity of oxytocin neurons is increased during breast feeding. Our finding that the oxytocinergic neural connection is likely to provide a direct transsynaptic mechanism by which the central nervous system maintains the state of infertility that accompanies lactation in mammals.
Journal of Practical Agriculture & Fisheries Research
/
v.20
no.2
/
pp.73-87
/
2018
The area of agriculture and fisheries business are expanding according to changes in the agriculture and fisheries environment. For the direction of long-term practical field training of department of Agriculture and Fisheries Business, which is a newly created department of Korea National College of Agriculture and Fisheries, production as well as other areas must be reviewed. The original long-term practical field training and the direction of selecting a long-term practical field training appropriate for the new department reviewed in this study are as follow. First, the original long-term practical field training can be summarized as single product-focused management, inadequate connection of production-processing-service areas, and individuality-focused management. However, a case management that sees new value creation as a basis of agricultural development can be summarized as diversification of value creation, horizontal integration, entrepreneurial management through corporate management, and leading management for regional revitalization through connecting local agricultural. Therefore, the direction of selecting the new department's long-term practical field training requires seeking of value creation management through horizontal integration, exploration of agricultural businessmen who have entrepreneurship needed to create added value in agriculture, and a way to connect to the original production-centered long-term practical field training.
본 웹사이트에 게시된 이메일 주소가 전자우편 수집 프로그램이나
그 밖의 기술적 장치를 이용하여 무단으로 수집되는 것을 거부하며,
이를 위반시 정보통신망법에 의해 형사 처벌됨을 유념하시기 바랍니다.
[게시일 2004년 10월 1일]
이용약관
제 1 장 총칙
제 1 조 (목적)
이 이용약관은 KoreaScience 홈페이지(이하 “당 사이트”)에서 제공하는 인터넷 서비스(이하 '서비스')의 가입조건 및 이용에 관한 제반 사항과 기타 필요한 사항을 구체적으로 규정함을 목적으로 합니다.
제 2 조 (용어의 정의)
① "이용자"라 함은 당 사이트에 접속하여 이 약관에 따라 당 사이트가 제공하는 서비스를 받는 회원 및 비회원을
말합니다.
② "회원"이라 함은 서비스를 이용하기 위하여 당 사이트에 개인정보를 제공하여 아이디(ID)와 비밀번호를 부여
받은 자를 말합니다.
③ "회원 아이디(ID)"라 함은 회원의 식별 및 서비스 이용을 위하여 자신이 선정한 문자 및 숫자의 조합을
말합니다.
④ "비밀번호(패스워드)"라 함은 회원이 자신의 비밀보호를 위하여 선정한 문자 및 숫자의 조합을 말합니다.
제 3 조 (이용약관의 효력 및 변경)
① 이 약관은 당 사이트에 게시하거나 기타의 방법으로 회원에게 공지함으로써 효력이 발생합니다.
② 당 사이트는 이 약관을 개정할 경우에 적용일자 및 개정사유를 명시하여 현행 약관과 함께 당 사이트의
초기화면에 그 적용일자 7일 이전부터 적용일자 전일까지 공지합니다. 다만, 회원에게 불리하게 약관내용을
변경하는 경우에는 최소한 30일 이상의 사전 유예기간을 두고 공지합니다. 이 경우 당 사이트는 개정 전
내용과 개정 후 내용을 명확하게 비교하여 이용자가 알기 쉽도록 표시합니다.
제 4 조(약관 외 준칙)
① 이 약관은 당 사이트가 제공하는 서비스에 관한 이용안내와 함께 적용됩니다.
② 이 약관에 명시되지 아니한 사항은 관계법령의 규정이 적용됩니다.
제 2 장 이용계약의 체결
제 5 조 (이용계약의 성립 등)
① 이용계약은 이용고객이 당 사이트가 정한 약관에 「동의합니다」를 선택하고, 당 사이트가 정한
온라인신청양식을 작성하여 서비스 이용을 신청한 후, 당 사이트가 이를 승낙함으로써 성립합니다.
② 제1항의 승낙은 당 사이트가 제공하는 과학기술정보검색, 맞춤정보, 서지정보 등 다른 서비스의 이용승낙을
포함합니다.
제 6 조 (회원가입)
서비스를 이용하고자 하는 고객은 당 사이트에서 정한 회원가입양식에 개인정보를 기재하여 가입을 하여야 합니다.
제 7 조 (개인정보의 보호 및 사용)
당 사이트는 관계법령이 정하는 바에 따라 회원 등록정보를 포함한 회원의 개인정보를 보호하기 위해 노력합니다. 회원 개인정보의 보호 및 사용에 대해서는 관련법령 및 당 사이트의 개인정보 보호정책이 적용됩니다.
제 8 조 (이용 신청의 승낙과 제한)
① 당 사이트는 제6조의 규정에 의한 이용신청고객에 대하여 서비스 이용을 승낙합니다.
② 당 사이트는 아래사항에 해당하는 경우에 대해서 승낙하지 아니 합니다.
- 이용계약 신청서의 내용을 허위로 기재한 경우
- 기타 규정한 제반사항을 위반하며 신청하는 경우
제 9 조 (회원 ID 부여 및 변경 등)
① 당 사이트는 이용고객에 대하여 약관에 정하는 바에 따라 자신이 선정한 회원 ID를 부여합니다.
② 회원 ID는 원칙적으로 변경이 불가하며 부득이한 사유로 인하여 변경 하고자 하는 경우에는 해당 ID를
해지하고 재가입해야 합니다.
③ 기타 회원 개인정보 관리 및 변경 등에 관한 사항은 서비스별 안내에 정하는 바에 의합니다.
제 3 장 계약 당사자의 의무
제 10 조 (KISTI의 의무)
① 당 사이트는 이용고객이 희망한 서비스 제공 개시일에 특별한 사정이 없는 한 서비스를 이용할 수 있도록
하여야 합니다.
② 당 사이트는 개인정보 보호를 위해 보안시스템을 구축하며 개인정보 보호정책을 공시하고 준수합니다.
③ 당 사이트는 회원으로부터 제기되는 의견이나 불만이 정당하다고 객관적으로 인정될 경우에는 적절한 절차를
거쳐 즉시 처리하여야 합니다. 다만, 즉시 처리가 곤란한 경우는 회원에게 그 사유와 처리일정을 통보하여야
합니다.
제 11 조 (회원의 의무)
① 이용자는 회원가입 신청 또는 회원정보 변경 시 실명으로 모든 사항을 사실에 근거하여 작성하여야 하며,
허위 또는 타인의 정보를 등록할 경우 일체의 권리를 주장할 수 없습니다.
② 당 사이트가 관계법령 및 개인정보 보호정책에 의거하여 그 책임을 지는 경우를 제외하고 회원에게 부여된
ID의 비밀번호 관리소홀, 부정사용에 의하여 발생하는 모든 결과에 대한 책임은 회원에게 있습니다.
③ 회원은 당 사이트 및 제 3자의 지적 재산권을 침해해서는 안 됩니다.
제 4 장 서비스의 이용
제 12 조 (서비스 이용 시간)
① 서비스 이용은 당 사이트의 업무상 또는 기술상 특별한 지장이 없는 한 연중무휴, 1일 24시간 운영을
원칙으로 합니다. 단, 당 사이트는 시스템 정기점검, 증설 및 교체를 위해 당 사이트가 정한 날이나 시간에
서비스를 일시 중단할 수 있으며, 예정되어 있는 작업으로 인한 서비스 일시중단은 당 사이트 홈페이지를
통해 사전에 공지합니다.
② 당 사이트는 서비스를 특정범위로 분할하여 각 범위별로 이용가능시간을 별도로 지정할 수 있습니다. 다만
이 경우 그 내용을 공지합니다.
제 13 조 (홈페이지 저작권)
① NDSL에서 제공하는 모든 저작물의 저작권은 원저작자에게 있으며, KISTI는 복제/배포/전송권을 확보하고
있습니다.
② NDSL에서 제공하는 콘텐츠를 상업적 및 기타 영리목적으로 복제/배포/전송할 경우 사전에 KISTI의 허락을
받아야 합니다.
③ NDSL에서 제공하는 콘텐츠를 보도, 비평, 교육, 연구 등을 위하여 정당한 범위 안에서 공정한 관행에
합치되게 인용할 수 있습니다.
④ NDSL에서 제공하는 콘텐츠를 무단 복제, 전송, 배포 기타 저작권법에 위반되는 방법으로 이용할 경우
저작권법 제136조에 따라 5년 이하의 징역 또는 5천만 원 이하의 벌금에 처해질 수 있습니다.
제 14 조 (유료서비스)
① 당 사이트 및 협력기관이 정한 유료서비스(원문복사 등)는 별도로 정해진 바에 따르며, 변경사항은 시행 전에
당 사이트 홈페이지를 통하여 회원에게 공지합니다.
② 유료서비스를 이용하려는 회원은 정해진 요금체계에 따라 요금을 납부해야 합니다.
제 5 장 계약 해지 및 이용 제한
제 15 조 (계약 해지)
회원이 이용계약을 해지하고자 하는 때에는 [가입해지] 메뉴를 이용해 직접 해지해야 합니다.
제 16 조 (서비스 이용제한)
① 당 사이트는 회원이 서비스 이용내용에 있어서 본 약관 제 11조 내용을 위반하거나, 다음 각 호에 해당하는
경우 서비스 이용을 제한할 수 있습니다.
- 2년 이상 서비스를 이용한 적이 없는 경우
- 기타 정상적인 서비스 운영에 방해가 될 경우
② 상기 이용제한 규정에 따라 서비스를 이용하는 회원에게 서비스 이용에 대하여 별도 공지 없이 서비스 이용의
일시정지, 이용계약 해지 할 수 있습니다.
제 17 조 (전자우편주소 수집 금지)
회원은 전자우편주소 추출기 등을 이용하여 전자우편주소를 수집 또는 제3자에게 제공할 수 없습니다.
제 6 장 손해배상 및 기타사항
제 18 조 (손해배상)
당 사이트는 무료로 제공되는 서비스와 관련하여 회원에게 어떠한 손해가 발생하더라도 당 사이트가 고의 또는 과실로 인한 손해발생을 제외하고는 이에 대하여 책임을 부담하지 아니합니다.
제 19 조 (관할 법원)
서비스 이용으로 발생한 분쟁에 대해 소송이 제기되는 경우 민사 소송법상의 관할 법원에 제기합니다.
[부 칙]
1. (시행일) 이 약관은 2016년 9월 5일부터 적용되며, 종전 약관은 본 약관으로 대체되며, 개정된 약관의 적용일 이전 가입자도 개정된 약관의 적용을 받습니다.