• Magazine of the Korean Society of Agricultural Engineers
• /
• v.44 no.2
• /
• pp.148-160
• /
• 2002

Lake water quality assessment information is useful to anyone involved in lake management, from lakeshore owners to lake associations. 11 provides lake water quality, which can improve how to manage lake resources and how to measure current conditions. It also provides a knowledge base that can be used to protect and restore lakes. SWMM was applied to simulate the discharge and pollutant loads from Boryeong watershed, and WASP5 was applied to analyze the changes of water quality in Boryeong freshwater lake. In each model, the most suitable parameters were calculated through sensitive analysis and some parameters used default data. Simulated in SWMM and measured discharge showed the accuracy of 88.6%. T-N and T-P exceeds the criteria in the simulation of water quality in Boryeong freshwater lake, and control of pollutant loads in the main stream showed the most effective way. Integrated water quality management system was developed to give convenience in the operation of SWMM and WASP5 and data acquisition.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.401-402
• /
• 2014

State of Charge (SOC) and State of Health (SOH) are the key issues for the application of Absorbent Glass Mat (AGM) type battery in Idle Start Stop (ISS) system which is popularly integrated in Electric Vehicles (EVs). However, battery parameters strongly depend on SOC, current rate and temperature and significantly change over the battery life cycles. In this research, a novel method for SOC, SOH estimation which combines the Auto Regressive with external input (ARX) method using for online parameters prediction and Dual Extended Kalman Filter (DEKF) algorithm considering hysteresis is proposed. The validity of the proposed algorithm is verified by the simulation and experiments.

• Proceedings of the KIPE Conference
• /
• 2014.07a
• /
• pp.71-72
• /
• 2014

This paper presents a method to find the fault location on the DC cables for the HVDC transmission systems which utilizes a hybrid topology of the diode rectifier and the voltage-source converter (VSC) in the wind farm (WF) side. First, the DC-cable fault occurring in this HVDC system is analyzed in detail. Then, the DC-cable fault location is detected from the two relative voltages located on the same section of the cable, which are estimated from a pair of DC-cable voltage and current measurements. The effectiveness of the method is verified by the simulation results.

• Proceedings of the KAIS Fall Conference
• /
• 2007.11a
• /
• pp.78-80
• /
• 2007

According to the development of VLSI integration technology and getting bigger the circuit size, it is a significant problem to verify systemized circuit. The faster and more accurate verification has very significant meaning in the field of electronic industry because it can yield the product comparably faster and reduce the trial and errors. In spite of the presence of various kind of Integrated Circuits it's not always easy to get the right part. Besides, it is hard to find a vendor for a small quantity consumers like who develop prototype applications. In this study, we've tried to get the logical signals from the PC based device we've developed that correspondents with the real ICs. It can emulate decoder ICs, multiplexers, demultiplexers and basic logic gates.

• Journal of Korea Multimedia Society
• /
• v.19 no.8
• /
• pp.1505-1515
• /
• 2016

The age of autonomous vehicles has come according to development of high performance sensing and artificial intelligence technologies. And importance of the vehicle's surrounding environment sensing and observation is increasing accordingly because of its stability and control efficiency. In this paper we propose an integrated platform for efficient networking, analysis and monitoring of multiple sensing data on the vehicle that are equiped with various automotive sensors such as GPS, weather radar, automotive radar, temperature and humidity sensors. From simulation results, we could see that the proposed platform could perform realtime analysis and monitoring of various sensing data that were observed from the vehicle sensors. And we expect that our system can support drivers or autonomous vehicles to recognize optimally various sudden or danger driving environments on the road.

• Proceedings of the Safety Management and Science Conference
• /
• 2008.11a
• /
• pp.555-560
• /
• 2008

Air logistics is getting growing continuously because customers need to increase rapidity and accuracy, but it isn't enough to study the process about air logistics in South Korea. We analyze the AS-IS process and problems by studying previous documents and researching in this field. We offer how to adopt the ways that are solutions concerning AS-IS process and benchmarking e-freight of IATA. Our suggestion reduces stakehoders' work load by using integrated system. We believe it will contribute to improve air logistics process by making simple the process.

• Journal of the Korea Society of Computer and Information
• /
• v.5 no.3
• /
• pp.76-83
• /
• 2000

The continuous time signal system by development of CMOS technology have been receiving consideration attention. In this paper, Low pass filter using new CMOS floating resistor have been designed with cut off frequency for speech signal Processing. Especially a new floating resistor consisting entirely of CMOS devices in saturation has been developed. Linearity within $\pm$0.04% is achieved through nonlinearity via current mirrors over an applied range of $\pm$1V The frequency response exceeds 10MHz, and the resistors are expected to be useful in implementing integrated circuit active RC filters. The low pass filter designed using this method has simpler structure than switched capacitofilter. So reduce the chip area. The characteristics of the designed low pass filter using this method are simulated by pspice program.

• ETRI Journal
• /
• v.40 no.6
• /
• pp.794-801
• /
• 2018

This paper proposes a novel graphene-based optical microelectromechanical systems MEMS accelerometer that is dependent on the intensity modulation and optical properties of graphene. The designed sensing system includes a multilayer graphene finger, a laser diode (LD) light source, a photodiode, and integrated optical waveguides. The proposed accelerometer provides several advantages, such as negligible cross-axis sensitivity, appropriate linearity behavior in the operation range, a relatively broad measurement range, and a significantly wider bandwidth when compared with other important contributions in the literature. Furthermore, the functional characteristics of the proposed device are designed analytically, and are then confirmed using numerical methods. Based on the simulation results, the functional characteristics are as follows: a mechanical sensitivity of 1,019 nm/g, an optical sensitivity of 145.7 %/g, a resonance frequency of 15,553 Hz, a bandwidth of 7 kHz, and a measurement range of ${\pm}10g$. Owing to the obtained functional characteristics, the proposed device is suitable for several applications in which high sensitivity and wide bandwidth are required simultaneously.

• Journal of information and communication convergence engineering
• /
• v.21 no.1
• /
• pp.1-8
• /
• 2023

This paper presents a design method for a wideband bandpass filter (BPF) which compensates for frequency dependency based on the image admittance and image phase. In the proposed method, new compensation methods for the admittance and phase are integrated with the conventional method. The proposed method improves the frequency shift and reduces the unwanted bandwidth when designing more than 20% of the Fractional Bandwidth (FBW), whereas the conventional method exhibits frequency degradation at only 10% FBW. The proposed design theory was verified by applying it to both lumped elements and distributed lines through circuit simulation and measurements without an optimization process. The measurement results demonstrate improvements in the frequency shift and target bandwidth. In the future, an accurate design method based on frequency dependence can be implemented for the next-generation broadband communication system applications.

• 제어로봇시스템학회:학술대회논문집
• /
• 2000.10a
• /
• pp.495-495
• /
• 2000

The Stewart platform manipulator is a closed-kinematis chain robot manipulator that is capable of providing high st겨ctural rigidity and positional accuracy. However, this is a complex structure, so controllability of the system is not so good. In this paper, it introduces a new robust motion control algorithm using partial state feedback for a class of nonlinear systems in the presence of modelling uncertainties and external disturbances. The major contribution of this work introduces the development and design of robust observer for the slate and the perturbation w.hich is integrated into a variable structure controller(VSC) structure. The combination of controller/observer gives rise to the robust routine called sliding mode control with sliding perturbation observer(SMCSPO). The optimal gains of SMCSPO are easily obtained by genetic algorithm. Simulation and experiment are presented in order to apply to the stewart platform manipulator. There results show highly' accuracy and performance.