• Journal of Sensor Science and Technology
• /
• v.30 no.6
• /
• pp.395-407
• /
• 2021

The effect of the specifications of a silicon-on-insulator vertical slot optical waveguide on the sensitivity of homogeneous and surface sensing configurations for TE and TM polarization, respectively, was systematically analyzed using numerical software. The specifications were optimized based on the confinement factor and transmission power of the TE-guided mode distributed in the slot. The waveguide sensitivities of homogeneous and surface sensing were calculated according to the specifications of the optimized slot optical waveguide.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.469-474
• /
• 2006

A $1{\times}16$ thermo-optic switch with small excess loss using multimode interference(MMI) couplers is designed, fabricated, and measured. This paper introduces the proposed $1{\times}16$ thermo-optic switch, and discusses the measurement results. The $1{\times}16$ thermo-optic switch is farmed as 4-stage which consists of 15 unit devices. The unit devices are the $2{\times}2$ thermo-optic switches with Mach-Zehnder interferometer(MZI) structure. The characteristics of the $1{\times}16$ thermo-optic switch depends strongly on each unit device. The unit deviceconsists of two 3-dB general interference MMI couplers and two single mode waveguide arms as a phase shifter. First of all, the 3-dB optical splitter and $2{\times}2$ MZI thermo-optic switch have been tested to confirm the characteristics of the unit devices of the $1{\times}16$ MZI thermo-optic switch. Using the measurement results of the unit devices, the $1{\times}16$ MZI thermo-optic switch can be produced with better characteristics. The resultant structure of the MMI coupler with the optical light source of wavelength of 1550nm for the $1{\times}16$ thermo-optic switch is that the width and the optimized length are $25{\mu}m\;and\;1580{\mu}m$, respectively. The smallest excess loss fur the unit device is -0.5dB and the average excess loss is -0.7dB.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 2007.06a
• /
• pp.159-160
• /
• 2007

• Korean Journal of Optics and Photonics
• /
• v.15 no.2
• /
• pp.142-148
• /
• 2004

We investigated a Ti:LiNbO$_3$ based integrated-optic polarization controller with a Ti-indiffused waveguide along the z-axis utilizing the electro-optic effect. The device consists of a first quarter-wave (λ/4) phase-shifter followed by a half-wave(λ/2) and a second quarter-wave(λ/4) wave-plate, which is rotated synchronously with the first quarter-wave phase-shifter. We analyzed the operation principles of the device utilizing cascaded transfer matrices based on Jones matrix and Poincare sphere, simulated driving voltages for various input states of polarization (SOP), and theoretically confirmed transformations from any arbitrary input SOP into any general output SOP.

• The Journal of the Korea institute of electronic communication sciences
• /
• v.15 no.4
• /
• pp.659-664
• /
• 2020

In this paper, we propose a silicon-based electro-optic (EO) modulator which can modulate a sign of a topological charge number l of |l|=1 orbital angular momentum (OAM) mode. The proposed EO modulator consists of position-dependent doped Si waveguide core and undoped SiO2, cladding, which enables control of the effective index and propagation loss of two OAM constitutive eigenmodes. The modulator functions as OAM mode maintaining waveguide at -0.33V and as topological charge sign inverter at 10V. The output OAM mode purity is calculated through electric field distribution, showing high purity of |l|>0.92 in both cases.

• Korean Journal of Optics and Photonics
• /
• v.17 no.5
• /
• pp.430-436
• /
• 2006

Polarization-independent $Ti:LiNbO_3\;2{\times}2$ optical add/drop multiplexer for the 1550nm wavelength region is fabricated. The device consists of two input waveguides, two polarization beam splitters. two polarization conversion/electrooptic tuning waveguide sections, and two output waveguides. The single mode channel waveguides for both TE and TM polarizations are fabricated on a x-cut $Ti:LiNbO_3$substrate by Ti diffusion. Spectral section is based on phase-matched polarization conversion due to shear strain induced by a thick $SiO_2$ grating overlay film. An applied voltage tunes the device by changing the waveguide birefringence, hence the optical wavelength at which most efficient polarization conversion occurs. Tuning rate of 0.094nm/V with a maximum range of 17nm has been obtained. The nearest side-lobe is about 8.2dB. The FWHM is 3.72nm.

• Korean Journal of Optics and Photonics
• /
• v.14 no.1
• /
• pp.38-43
• /
• 2003

Fabrication process of strain-induced channel waveguides in $LiNbO_3$ was developed using strain-optic effect and compressional strain due to ~1.4 $\mu\textrm{m}$ surface Mo/Pt metal film. Characterization of the channel waveguides revealed a single transverse and depth mode in both TE and TM polarizations. Measurements showed total insertion loss of 6.2 and 7.7 ㏈/cm for TM and TE polarizations. respectively. Electro-optic intensity modulators with 11 mm long electrode length and 21 $\mu\textrm{m}$ electrode gap at $\lambda$ = 1.15 ${\mu}{\textrm}{m}$have been produced in $LiNbO_3$ substrates using strain-induced channel waveguides. Modulation depth of 100% at $\pi$-radian voltage of 16.1V has been demonstrated. Also, 1$\times$2 on/off power splitters at $\lambda$ = 0.63 $\mu\textrm{m}$ have been produced using strain-induced channel waveguides. On/off voltage of $\pm$ 25V has been demonstrated.

• Smart Structures and Systems
• /
• v.20 no.4
• /
• pp.441-450
• /
• 2017

The objective of this work is to present a conceptual design and the modelling of a distributed sensor system based on fiber optic devices (Fiber Bragg Grating, FBG), aimed at measuring span-wise and chord-wise variations of an adaptive (morphing) trailing edge. The network is made of two different integrated solutions for revealing deformations of the reference morphing structure. Strains are confined to typical values along the span (length) but they are expected to overcome standard ranges along the chord (width), up to almost 10%. In this case, suitable architectures may introduce proper modulations to keep the measured deformation low while preserving the information content. In the current paper, the designed monitoring system combines the use of a span-wise fiber reinforced patch with a chord-wise sliding beam. The two elements make up a closed grid, allowing the reconstruction of the complete deformed shape under the acceptable assumption that the transformation refers to regular geometry variations. Herein, the design logic and some integration issues are reported. Preliminary experimental test results are finally presented.

• Proceedings of the KIEE Conference
• /
• 1992.07a
• /
• pp.362-364
• /
• 1992

In this paper, the development of a fiber optic network for an integrated digital protection relay system is described. The structure of the developed network is determined to loosen the optic requirements and to have good extensibility while providing sufficient functions for protection and control for substations. The network has a hierarchical structure with two levels. The upper level handles data for monitoring and control of the system with star topology. The lower level manages the real time data for bus protection with one-to-one connections. Communication flows of each level are described. The HDLC is employed as the network protocol.

• ETRI Journal
• /
• v.28 no.1
• /
• pp.103-106
• /
• 2006

We have fabricated a planar lightwave circuit (PLC) hybrid-integrated optical sub-assembly of a triplexer using a thin film filter (TFF)-attached wavelength division multiplexer (WDM) and photodiode (PD) carriers. Two types of TFFs were attached to a diced side of a silica-terraced PLC platform, and the PD carriers with a $45^{\circ}$ mirror on which pin-PDs were bonded were assembled with the platform. A clear transmitter eye-pattern and minimum receiver sensitivity of -24.5 dBm were obtained under 1.25 Gb/s operation for digital applications, and a second-order inter-modulation distortion (IMD2) of -70 dBc was achieved for an analog receiver.