• Advances in nano research
• /
• v.16 no.6
• /
• pp.565-577
• /
• 2024

Vibration investigation of fluid-filled functionally graded cylindrical shells with ring supports is studied here. Shell motion equations are framed first order shell theory due to Sander. These equations are partial differential equations which are usually solved by approximate technique. Robust and efficient techniques are favored to get precise results. Employment of the Rayleigh-Ritz procedure gives birth to the shell frequency equation. Use of acoustic wave equation is done to incorporate the sound pressure produced in a fluid. Hankel's functions of second kind designate the fluid influence. Mathematically the integral form of the Langrange energy functional is converted into a set of three partial differential equations. A cylindrical shell is immersed in a fluid which is a non-viscous one. These shells are stiffened by rings in the tangential direction. For isotropic materials, the physical properties are same everywhere where the laminated and functionally graded materials, they vary from point to point. Here the shell material has been taken as functionally graded material. After these, ring supports are located at various positions along the axial direction round the shell circumferential direction. The influence of the ring supports is investigated at various positions. Effect of ring supports with empty and fluid-filled shell is presented using the Rayleigh - Ritz method with simply supported condition. The frequency behavior is investigated with empty and fluid-filled cylindrical shell with ring supports versus circumferential wave number and axial wave number. Also the variations have been plotted against the locations of ring supports for length-to-radius and height-to-radius ratio. Moreover, frequency pattern is found for the various position of ring supports for empty and fluid-filled cylindrical shell. The frequency first increases and gain maximum value in the midway of the shell length and then lowers down. It is found that due to inducting the fluid term frequency result down than that of empty cylinder. It is also exhibited that the effect of frequencies is investigated by varying the surfaces with stainless steel and nickel as a constituent material. To generate the fundamental natural frequencies and for better accuracy and effectiveness, the computer software MATLAB is used.

• Journal of the Korean Geographical Society
• /
• v.30 no.1
• /
• pp.35-56
• /
• 1995

During the last two decades, Korea has achieved remarkable economic growth. In this process the nation has become urbanized and industrialized. But we have also encountered widening regional disparity, housing shortage of larger cities, transportation congestion, environmental pollution and many other problems. Rapid increasing urbanization and continuous migration toward Seoul since the late 1960s have been one of the major concerns of government. Government has sought ways to moderate the population increase in Seoul. The regulation which include new town development near Seoul and dispersion strategies of higher education and other administration and living facilities outside of Seoul havemade a great expansion of the spatial influence of Seoul city. Seoul metropolitan reaion has evolved as the most powerful center of political and economical spaces. Generally within a metropolitan region, there exists a growing mutual interdependence economically, as well as socially between a central city and its surrounding area. Seoul metropolitan region manifests itself not only as a coherent system of urbanized regions, but also as an integral part of the daily urban system. The surrounding Gyunggi province and Seoul city become closely linked both economically and functionally, constituting true functlonai urban system. This study is primarily undertaken with the purpose of delineation of the sphere of influence of Seoul city in 1990. At the time of 1985, Seoul metropolitan region was delineated according to the result of the study which was performed by Korea Research Institute for Human Settlements. Afterward, the rapid speed of metropolitanization process with dramatic increase in mobility through the provision of wider transportation system across the Capital region have evolved, resulting in the great expansion of the spatial influence of Seoul city. So this study examines the expanded area of Seoul metropolitan regin during the period of 1985-90. In order to delineate Seoul metropolitan region, the indices of urbanization and functional linkage are selected. Variables included in the measurement of the urbanization level are agricultural structure, population characteristics, manufacturing and service industries, and cultural aspects such as newspaper circulation, the ratio of car ownership and piped water supply. Variables included in the measurement of functional linkage are commuting, shopping pattern, centralized service such as medical facilities and trade of agricultural products. The standardization method and factor analysis are employed in making the delineation of Seoul metropolitan region. According to the result of this study, 2 cities, 8 Eups and 46 Myuns are included Seoul metropolitan region in 1990. If we compare this delineated area in 1990 to that of 1985, we can find the distinctive pattern of expanded axes according to the main transportation routes such as Seoul-Suweon, Seoul-Gwangju, Seoul-Incheon. In 199O, all the Gyunggi province, except a few Myuns located at the north and northwest part of Gyunggi province, are included in Seoul metropolitan region. Furthermore, this study attempts to the analysis of regional structure of Seoul metropolitan region according to the functional characteristics of each city and Gun. Variables included in this analysis are the new residential function, manufacturing function, service function, education and infermation function, public facility function and agricultural function. Factor analysis and cluster analysis are employed in making regionalization. Seoul metropolitan reaion is subdivided into four subregions which reflect different functional specialization. The first group is the specialized region of newly formed residential function. The second group is the specialized reaion of manufacturing function. The third group is the specialized region of service function. And the fourth group has little specialized in terms of manufacturing, service, and residential function. But this region has some potentiality of development when Seoul metropolitan region grow continuously. Seoul metropolitan region accounted for 43% of national population, despite 11.8% of national land size in 1990. Although Seoul metropolitan region enjoys important agglomeration economies, it also has huge social cost in the form of transportation congestion, housing shortage, rapid increase of land value, environment pollution, and etc. Efficient metropolitan plan making is a vital element in promoting Seoul's economic development and providing high quality living environment at low cost. In the light of the result of this study, the outer ring of Seoul metropolitan region, especially northeastern part, are underdeveloped compared to overdeveloped southwestern area. It is needed to develop the guidelines for the implement of the growth control and management plan, inducing more balanced development for whole Seoul metropolitan reaion.

• Journal of Bio-Environment Control
• /
• v.21 no.3
• /
• pp.243-246
• /
• 2012

The study was aimed at the development of the simple linear regression model to estimate the fruit yield of sweet pepper and to support decision-making management for growing sweet pepper crop in Korea. For quantitative analysis of relationship between environmental data and periodical yield of sweet pepper the data obtained from the commercial Venlo-type glasshouse for 2 years. Obtained periodical yield data of five different cultivars and radiation data were accumulated and fitted by linear regression. A significant linear relationship was found between radiation integral and fruit yield, whereas the production per unit of radiation was different between cultivars. The slope of linear regression could indicate as light use efficiency for fruit production ($LUE_F$, $g{\cdot}MJ^{-1}$). $LUE_F$ of 'Ferrari' was $5.85g{\cdot}MJ^{-1}$, 'Fiesta' 5.32 for first year and $4.75g{\cdot}MJ^{-1}$ and for second year, 'President' was $4.66g{\cdot}MJ^{-1}$, 'Cupra' was $3.86g{\cdot}MJ^{-1}$, and 'Boogie' was $6.48g{\cdot}MJ^{-1}$. The amount of light requirement for the unit gram of fruit was between $25.88J{\cdot}g^{-1}$, for 'Cupra' and $15.42J{\cdot}g^{-1}$ for 'Boogie'. Although we found the linear relationship between radiation and fruit yield, $LUE_F$ was varied between cultivars and as well as year. The linear relationship could describe the fruit yield as function of radiation, but it needed more variable to generalization of the production, such as cultivar specifications, temperature, and number of fruits set per plant or unit of ground.

• Journal of the Korean Institute of Landscape Architecture
• /
• v.44 no.2
• /
• pp.83-95
• /
• 2016

Strategies for parks and open spaces in the 21st century have moved from focusing on specific elements, such as quantitative growth and ecological and recreational aspects, to green infrastructure, which refers to a multi-functional network of open and green spaces offering a range of benefits. In the case of London, green infrastructure is realised as an integral part of urban infrastructure, involving physical and social infrastructure as well as practical spatial planning at the local level within statutory urban planning as part of a continuously developing green infrastructure framework with a theoretical basis. Taking this perspective, the present study looks at alterations to and developments in green infrastructure policies in the London Plan, the green grid framework as detailed in the city's strategic implementation of green infrastructure. Various trends and characteristics of the policies adopted in the London Plan and some implications are deduced, with three main results being identified. The first is a clear division of roles among the national government, Greater London Authority and borough councils, with local plans established under the guidance of the National Planning Policy Framework (NPPF) and the London Plan. Green infrastructure policies in the London Plan have been applied at a high rate in the boroughs' local plans, which leads to another, linked point. Secondly, green infrastructure policies and the green grid as an implementation framework have been consistently extended and developed through consolidating the London Plan, despite the change of government. Finally, in order to achieve the London Plan, the Mayor of London implemented policies by partnership and supporting programmes for London boroughs. Recently, the Seoul Metropolitan Authority introduced a parks and green spaces development policy, but the London case remains a good example; this is because green infrastructure policies in London were not a manifesto pledge but rather have been continuously and consistently advanced regardless of party politics and thus realised as long-term planning.

• Journal of Korea Port Economic Association
• /
• v.24 no.4
• /
• pp.363-384
• /
• 2008

This study aims at improving Korea's competitiveness in port logistics through marketing strategy with integrating the conceptual approach into the empirical one and combining both the oldest military treatise and the newest evaluating model in social science that was applied by the HFP(hierarchical fuzzy process) model enhanced by the KJ method. The empirical results of this study show Busan in the middle among subject ports. At present, Korea plays a reciprocal role in the port market in East Asia, but in the medium- and long-term, Korea's ports will vie together with most major ports in the East Asian region. A descriptive investigation shows that Korea's developing tasks in port logistics must be considered in the context of the direction for developing port policies, the necessity of expanding port facilities in the capital region, securing the sufficient traffic volume through the establishment of the hinterland linking system and its positive utilization, and reforming the direction for developing the global logistics through increased port competitiveness. In the short- and medium-term, Korea must use the opportunity factor of 'Growth and open door policy of China' as a geoeconomic advantage and to utilize Korea's ports as a gate to Chinese foreign trade. With the rise of China's economy, China also plays a significant role in both port and airport markets. Hence, the linking system between the two must be established to meet the expanding traffic volume, especially in the capital area. Moreover, it is necessary for Korea to secure port logistics through the establishment of the hinterland linking system and its positive utilization. The great accomplishment of this paper is to present strategies to increase Korea's port competitiveness in the rapidly changing environments of world logistics with the focus on both the oldest military strategic treatise and the newest empirical method in social science. In order to reinforce this study, it needs further compensative research because the evaluation structure could be subdivided with more extensive and precise criteria.

• Proceedings of the Korean Reliability Society Conference
• /
• 2001.06a
• /
• pp.277-278
• /
• 2001

The successful operation of a product In service depends upon the effective provision of logistic support in order to achieve and maintain the required levels of performance and customer satisfaction. Logistic support encompasses the activities and facilities required to maintain a product (hardware and software) in service. Logistic support covers maintenance, manpower and personnel, training, spares, technical documentation and packaging handling, storage and transportation and support facilities.The cost of logistic support is often a major contributor to the Life Cycle Cost (LCC) of a product and increasingly customers are making purchase decisions based on lifecycle cost rather than initial purchase price alone. Logistic support considerations can therefore have a major impact on product sales by ensuring that the product can be easily maintained at a reasonable cost and that all the necessary facilities have been provided to fully support the product in the field so that it meets the required availability. Quantification of support costs allows the manufacturer to estimate the support cost elements and evaluate possible warranty costs. This reduces risk and allows support costs to be set at competitive rates.Integrated Logistic Support (ILS) is a management method by which all the logistic support services required by a customer can be brought together in a structured way and In harmony with a product. In essence the application of ILS:- causes logistic support considerations to be integrated into product design;- develops logistic support arrangements that are consistently related to the design and to each other;- provides the necessary logistic support at the beginning and during customer use at optimum cost.The method by which ILS achieves much of the above is through the application of Logistic Support Analysis (LSA). This is a series of support analysis tasks that are performed throughout the design process in order to ensure that the product can be supported efficiently In accordance with the requirements of the customer.The successful application of ILS will result in a number of customer and supplier benefits. These should include some or all of the following:- greater product uptime;- fewer product modifications due to supportability deficiencies and hence less supplier rework;- better adherence to production schedules in process plants through reduced maintenance, better support;- lower supplier product costs;- Bower customer support costs;- better visibility of support costs;- reduced product LCC;- a better and more saleable product;- Improved safety;- increased overall customer satisfaction;- increased product purchases;- potential for purchase or upgrade of the product sooner through customer savings on support of current product.ILS should be an integral part of the total management process with an on-going improvement activity using monitoring of achieved performance to tailor existing support and influence future design activities. For many years, ILS was predominantly applied to military procurement, primarily using standards generated by the US Government Department of Defense (DoD). The military standards refer to specialized government infrastructures and are too complex for commercial application. The methods and benefits of ILS, however, have potential for much wider application in commercial and civilian use. The concept of ILS is simple and depends on a structured procedure that assures that logistic aspects are fully considered throughout the design and development phases of a product, in close cooperation with the designers. The ability to effectively support the product is given equal weight to performance and is fully considered in relation to its cost.The application of ILS provides improvements in availability, maintenance support and longterm 3ogistic cost savings. Logistic costs are significant through the life of a system and can often amount to many times the initial purchase cost of the system.This study provides guidance on the minimum activities necessary to Implement effective ILS for a wide range of commercial suppliers. The guide supplements IEC60106-4, Guide on maintainability of equipment Part 4: Section Eight maintenance and maintenance support planning, which emphasizes the maintenance aspects of the support requirements and refers to other existing standards where appropriate. The use of Reliability and Maintainability studies is also mentioned in this study, as R&M is an important interface area to ILS.

• Journal of the Korean Geographical Society
• /
• v.30 no.2
• /
• pp.169-187
• /
• 1995

Contemporary US metropolitan areas have undergone divergent economic transformation, and as a result labor markets have become the focus of concern in their role as determinants of earnings attainment. Explanations of individual earnings attainmnent as a lobor market outcome have been established in two diafferent stances one who emphasizes personal or group attributes in the human capital perspective and the other who emphasizes economic structure in the labor market segmentation perspective. While remaining at the conceptual level and yet relatively unexplored, the importance of place in labormarket operation is a significant advancement as it appears in labor market areas and local labor markets considering that labor market areas represent the intersection of labor market structure and individual labor market experiences at specific geographic places. The substantive inquiry of this study was to explore labor market characteristics and their differentiation across large metropolitan areas, and assess their effects on the individual earnings attainment. Integating individual attributes and labor market characteristics as major factors of labor market operation, this study intended to contextualize individual earnings attainment with geographic labor market areas. Using 1990 US population census 5% "Public-Use Microdata Samples, " the largest 65 metropolitan areas were first selected and employed male workers who are aged between 25 and 50 for whites, blacks, asians, and hispanics. As an initial step earnings differentials between racial/ethnic groups and selected 65 metropolitan areas were examined using analysis of variance, and then earnings differentials were attributed to the individual attributes such as education, age, and immigration status, and four dimensions of metropolitan labor market differentiation devised by principal component analysis of industrial and occupational segments: Public versus Blue Collar Core(CS1), Finance-Core Utility versus Blue Collar Local Monopoly (CS2), Oligopoly versus Blue Collar Periphery(CS3), and Self Employed-White Collar Periphery versus Low-Skill Core(CS4). As a final analysis, individual earnings were related to each individual attribute and its interaction with metropolitan labor market characteristics to examine how the differentiated metropolitan labor market characteristics alter the role of individual attributes on earnings attainment. The findings indicated that individual attributes, education in particular exert significant effects on earnings attainment, but their effects were significantly altered by metropolitan labor market characterristics. Particularly important dimensions were: Oligopoly differentiated from Blue Colla Periphery metropolitan areas enhancing earnings returns to individual attributes for all groups but minority groups (black, asians, hispanics) rely more on this, and Finance-Core Utility differentiated from Blue Collar Local Monopoly metropolitan areas provide higher earnings returns to whites exclusively. These findings suggest that individuals with identical individual attributes involving racial/ethnic categories would have different earnings atteinments depending on the metropolitan labor market characteristics where they reside. Referring back to the major traditions of the human capital and the labor market segmentation in labor market research, the interaction between individual attributes and metropolitan labor market haracteristics on earnings attainment highlights the complimentary nature of the two on earnings determination in particular geographic places, Hence, labor market characteristics differentiatcd across metropolitan areas are an integral part of labor market operation which should be considered for the explanation of individual earnings attainment and racial/ethnic group earnings differentials. Gcographic places are the important contexts for labor market segmentation and individual labor market experiences. In conclusion, this study brings geographic labor markets to the forefront in the examination of individuals' earnings attainments. The empirical vaidation of the role of metropolitan labor market charecteristics on earnings attainment, while exploratory contributes towards a broader perspective of geographic labor market research that recognizes that individuals' labor market experiences are intertwined with geographic contexts of labor market operatin. operatin.

• The korean journal of orthodontics
• /
• v.28 no.5 s.70
• /
• pp.699-716
• /
• 1998

This study was designed to evaluate the expression of non-collagenous protein in periodontal tissue during the experimental movement of rat incisors, by LSAB(labelled streptavidine biotin) immunohistochemical staining for osteonectin and osteocalcin. Twenty seven Sprague-Dawley rats were divided into a control group(3 rats) and 6 experimental groups(24 rats) where 75g of force was applied from helical springs across the maxillary incisors. Rats of experimental groups were sacrificed at 12 hours, 1, 4, 7, 14 and 28 days after force application, respectively. And the tissues of a control group and experimental groups were studied immunohistochemically and histologically. The results were as follows : 1. Until 28 days after force application, periodontal fibers had been strectched on tension side and compressed in pressure side of all the experimental groups, and the arrangement of periodontal fibers had not been recovered yet. 2. The expression of osteonectin in control group was rare in dentin, cementum and osteocyte, and was mild in odontoblasts and matrix of alveolar bone. 3. The expression of osteocalcin in control group was negative in gingiva, osteoblasts, osteocyte and cementum, and was rare in predentin, capillaries in pulp and periodontal ligament and the matrix of alveolar bone. 4. There was no difference in the expression of osteocalcin or osteonectin in dentin, cementum, pulp, odontoblasts, between of control and of experimental groups. 5. The expression of osteonectin in intermaxillary suture got the peak in 7-day and was declined after 14-day. The expression of osteocalcin remained in a same degree since it became mild in 14-day. 6. The expression of osteonectin in pressure side of periodontal ligament of experimental group was rare, which was similar to control group. But in tension side, it was increased until 14-day aftrer which it was declined. 7. The expression of osteocalcin in periodntal ligament was rare in 12-hour to 14-day, but became severe in 28-day, which was greater in tension side than in pressure side, and in the periodontal fiber next to alveolar bone than to tooth surface. 8. The expression of osteocalcin in alveolar bone was rare until 14-day in pressure side, but became moderate in 28-day. The expression of osteonectin was increased from 7-day by time dependency, which was greater in tension side than in pressure side.

• Asia pacific journal of information systems
• /
• v.17 no.4
• /
• pp.207-228
• /
• 2007

Measuring Information Technology(IT) organizations' activities have been limited to mainly measure financial indicators for a long time. However, according to the multifarious functions of Information System, a number of researches have been done for the new trends on measurement methodologies that come with financial measurement as well as new measurement methods. Especially, the researches on IT Balanced Scorecard(BSC), concept from BSC measuring IT activities have been done as well in recent years. BSC provides more advantages than only integration of non-financial measures in a performance measurement system. The core of BSC rests on the cause-and-effect relationships between measures to allow prediction of value chain performance measures to allow prediction of value chain performance measures, communication, and realization of the corporate strategy and incentive controlled actions. More recently, BSC proponents have focused on the need to tie measures together into a causal chain of performance, and to test the validity of these hypothesized effects to guide the development of strategy. Kaplan and Norton[2001] argue that one of the primary benefits of the balanced scorecard is its use in gauging the success of strategy. Norreklit[2000] insist that the cause-and-effect chain is central to the balanced scorecard. The cause-and-effect chain is also central to the IT BSC. However, prior researches on relationship between information system and enterprise strategies as well as connection between various IT performance measurement indicators are not so much studied. Ittner et al.[2003] report that 77% of all surveyed companies with an implemented BSC place no or only little interest on soundly modeled cause-and-effect relationships despite of the importance of cause-and-effect chains as an integral part of BSC. This shortcoming can be explained with one theoretical and one practical reason[Blumenberg and Hinz, 2006]. From a theoretical point of view, causalities within the BSC method and their application are only vaguely described by Kaplan and Norton. From a practical consideration, modeling corporate causalities is a complex task due to tedious data acquisition and following reliability maintenance. However, cause-and effect relationships are an essential part of BSCs because they differentiate performance measurement systems like BSCs from simple key performance indicator(KPI) lists. KPI lists present an ad-hoc collection of measures to managers but do not allow for a comprehensive view on corporate performance. Instead, performance measurement system like BSCs tries to model the relationships of the underlying value chain in cause-and-effect relationships. Therefore, to overcome the deficiencies of causal modeling in IT BSC, sound and robust causal modeling approaches are required in theory as well as in practice for offering a solution. The propose of this study is to suggest critical success factors(CSFs) and KPIs for measuring performance for IT organizations and empirically validate the casual relationships between those CSFs. For this purpose, we define four perspectives of BSC for IT organizations according to Van Grembergen's study[2000] as follows. The Future Orientation perspective represents the human and technology resources needed by IT to deliver its services. The Operational Excellence perspective represents the IT processes employed to develop and deliver the applications. The User Orientation perspective represents the user evaluation of IT. The Business Contribution perspective captures the business value of the IT investments. Each of these perspectives has to be translated into corresponding metrics and measures that assess the current situations. This study suggests 12 CSFs for IT BSC based on the previous IT BSC's studies and COBIT 4.1. These CSFs consist of 51 KPIs. We defines the cause-and-effect relationships among BSC CSFs for IT Organizations as follows. The Future Orientation perspective will have positive effects on the Operational Excellence perspective. Then the Operational Excellence perspective will have positive effects on the User Orientation perspective. Finally, the User Orientation perspective will have positive effects on the Business Contribution perspective. This research tests the validity of these hypothesized casual effects and the sub-hypothesized causal relationships. For the purpose, we used the Partial Least Squares approach to Structural Equation Modeling(or PLS Path Modeling) for analyzing multiple IT BSC CSFs. The PLS path modeling has special abilities that make it more appropriate than other techniques, such as multiple regression and LISREL, when analyzing small sample sizes. Recently the use of PLS path modeling has been gaining interests and use among IS researchers in recent years because of its ability to model latent constructs under conditions of nonormality and with small to medium sample sizes(Chin et al., 2003). The empirical results of our study using PLS path modeling show that the casual effects in IT BSC significantly exist partially in our hypotheses.

• International Journal of Ocean System Engineering
• /
• v.2 no.3
• /
• pp.185-194
• /
• 2012

A Macroscopic combination of two or more distinct materials is commonly referred to as a "Composite Material", having been designed mechanically and chemically superior in function and characteristic than its individual constituent materials. Composite materials are used not only for aerospace and military, but also heavily used in boat/ship building and general composite industries which we are seeing increasingly more. Regardless of the various applications for composite materials, the industry is still limited and requires better fabrication technology and methodology in order to expand and grow. An example of this is that the majority of fabrication facilities nearby still use an antiquated wet lay-up process where fabrication still requires manual hand labor in a 3D environment impeding productivity of composite product design advancement. As an expert in the advanced composites field, I have developed fabrication skills with the use of machinery based on my past composite experience. In autumn 2011, the Korea government confirmed to fund my project. It is the development of a composite sanding machine. I began development of this semi-robotic prototype beginning in 2009. It has possibilities of replacing or augmenting the exhaustive and difficult jobs performed by human hands, such as sanding, grinding, blasting, and polishing in most often, very awkward conditions, and is also will boost productivity, improve surface quality, cut abrasive costs, eliminate vibration injuries, and protect workers from exposure to dust and airborne contamination. Ease of control and operation of the equipment in or outside of the sanding room is a key benefit to end-users. It will prove to be much more economical than normal robotics and minimize errors that commonly occur in factories. The key components and their technologies are a 360 degree rotational shoulder and a wrist that is controlled under PLC controller and joystick manual mode. Development on both of the key modules is complete and are now operational. The Korean government fund boosted my development and I expect to complete full scale development no later than 3rd quarter 2012. Even with the advantages of composite materials, there is still the need to repair or to maintain composite products with a higher level of technology. I have learned many composite repair skills on composite airframe since many composite fabrication skills including repair, requires training for non aerospace applications. The wind energy market is now requiring much larger blades in order to generate more electrical energy for wind farms. One single blade is commonly 50 meters or longer now. When a wind blade becomes damaged from external forces, on-site repair is required on the columns even under strong wind and freezing temperature conditions. In order to correctly obtain polymerization, the repair must be performed on the damaged area within a very limited time. The use of pre-impregnated glass fabric and heating silicone pad and a hot bonder acting precise heating control are surely required.