• 한국안전학회지
• /
• 제33권4호
• /
• pp.119-126
• /
• 2018

In recent years, as flood damage caused by heavy rains increased, the great-depth tunnel using urban underground space is emerging as a countermeasure of urban inundation. The great-depth tunnel is used to reduce urban inundation by using the underground space. The drainage efficiency of great-depth tunnel depends on the intake design, which leads to increase discharge into the underground space. The spiral intake and the tangential intake are commonly used for the inlet facility. The spiral intake creates a vortex flow along the drop shaft and reduces an energy of the flow by the wall friction. In the tangential intake, flow simply falls down into the drop shaft, and the design is simple to construct compared to the spiral intake. In the case of the spiral intake, the water level at the drop shaft entrance is risen due to the chocking induced by the flowrate increase. The drainage efficiency of the tangential intake decreases because the flow is not sufficiently accelerated under low flow conditions. Therefore, to compensate disadvantages of the previously suggested intake design, the multi-stage intake was developed which can stably withdraw water even under a low flow rate below the design flow rate. The hydraulic characteristics in the multi-stage intake were analyzed by changing the flow rate to compare the drainage performance according to the intake design. From the measurements, the drainage efficiency was improved in both the low and high flow rate conditions when the multi-stage inlet was employed.

• 한국소음진동공학회논문집
• /
• 제12권10호
• /
• pp.773-784
• /
• 2002

This paper proposes an optimal design to improve the performance of the intake system by reducing the noise. We adapt the Taguchi method and column merging method for the above design. At the first stage of the design, the length and radius of each component of the current intake system are selected as control factors. Then the $L^{18}$ table of orthogonal array is used to get the effective main factors. At the second stage, the $L^{16}$ table of orthogonal array and the column merging method is combined to analyze subdivided significant factors. We know that the robust design with the column merging method provides better design for noise of intake system than the robust design itself.

• 한국소음진동공학회논문집
• /
• 제15권10호
• /
• pp.1123-1130
• /
• 2005

We propose an optimal design to improve the capacity by reducing the noise of the intake system. The length and radius of each component of the current Intake system are selected as control factors. We accept the output from computer simulator with orthogonal arrays. Then, the Kriging estimates are computed. From this, we exploit the optimal design of the intake system by adapting simulated annealing. From the results of this optimal design, we conclude that Kriging method with the orthogonal arrays is the efficient method for Design and Analysis of Computer Experiments and we propose the useful results for the low noise intake system.

• 대한기계학회논문집A
• /
• 제30권4호
• /
• pp.465-472
• /
• 2006

Recently, the regulations of the government and the concerns of people have rise to the interest in noise pollution levels as compared to other vehicles. In this area, many researchers have studied to reduce this noise in the field of automotive engineering. This paper proposes an optimal design scheme to reduce the noise of the intake system by adapting Kriging with two meta-heuristic techniques. For this, as a measuring tool for the performance of the intake system, the performance prediction software, was used. Then, the length and radius of each component of the current intake system are selected as input variables and the orthogonal arrays is adapted as a space-filling design. With these simulated data, we can estimate a correlation parameter in Kriging by solving the nonlinear problem with a genetic algorithm and find an optimal level for the intake system by optimizing Kriging estimated with simulated annealing. We notice that this optimal design scheme gives noticeable results and is a preferable way to analyze the intake system. Therefore, an optimal design for the intake system is proposed by reducing the noise of its system.

• 한국자동차공학회논문집
• /
• 제5권5호
• /
• pp.104-113
• /
• 1997

In this paper, the effects of intake manifold systems on volumetric efficiency were investigated in the 4-cylinder 4-stroke cycle diesel engines. The effects of intake manifold system were analyzed on resonant speed and on volumetric efficiency. Resonant speed was calculated by acoustic theory and volumetric efficiency by the method of characteristics. The calculation results agreed well with rest results. It was assured that between the resonant speed and the volumetric efficiency there exists good correlation in multi-cylinder engines. As the results, the prediction of resonant speed was useful to design the optimum intake system. It was assured that the intake manifold systems for BOX-type and RAM-type have different characteristics on the trend of volumetric efficiency. Also a procedure to design the desirable intake manifold system was proposed.

• 한국전산유체공학회지
• /
• 제11권1호
• /
• pp.57-66
• /
• 2006

An optimal shape design approach is presented for a subsonic S-shaped intake using aerodynamic sensitivity analysis. Two-equation turbulence model is employed to capture strong counter vortices in the S-shaped duct more precisely. Sensitivity analysis is performed for the three-dimensional Navier-Stokes equations coupled with two-equation turbulence models using a discrete adjoint method For code validation, the result of the flow solver is compared with experiment data and other computational results of bench marking test. To study the influence oj turbulence models and grid refinement on the duct flow analysis, the results from several turbulence models are compared with one another and the minimum number of grid points, which can yield an accurate solution is investigated The adjoint variable code is validated by comparing the complex step derivative results. To realize a sufficient and flexible design space, NURBS equations are introduced as a geometric representation and a new grid modification technique, Least Square NURBS Grid Approximation is applied With the verified flow solver, the sensitivity analysis code and the geometric modification technique, the optimization of S-shaped intake is carried out and the enhancement of overall intake performance is achieved The designed S-shaped duct is tested in several off-design conditions to confirm the robustness of the current design approach. As a result, the capability and the efficiency of the present design tools are successfully demonstrated in three-dimensional highly turbulent internal flow design and off-design conditions.

• 한국농공학회지
• /
• 제30권2호
• /
• pp.67-81
• /
• 1988

The purpose of the present study is to set up an efficient optimum design method for the large-scale reinforced concrete cylindrical shell structures like intake tower of reservoir and to establish a solid foundation for the automatic optimum structural design combined with finite element analysis. The major design variables are the dimensions and steel areas of each member of the structures. The construction cost which is composed of the concrete, steel, and form work costs, respectively, is taken as the objective function. The constraint equations for the design of intake-tower are derived on the basis of the working stress design method. The corresponding design guides including the standard specification for concrete structures have been also employed in deraving the constraint conditions. The present nonlinear optimization problem is solved by SUMT method. The reinforced concrete intake-tower is decomposed into three major substructures. The optimization is then conducted for both the whole structure and the substructures. The following conclusions can be drawn from the present study. 1. The basis of automatic optimum design of reinforced concrete cylindrical shell structures which is combined with finite element analysis was established. 2. The efficient optimization algorithms which can execute the automatic optimum desigh of reinforced concrete intake-tower based on the working stress design method were developed. 3. Since the objective function and design variables were converged to their optimum values within the first or second iteration, the optImization algorithms developed in this study seem to be efficient and stable. 4. The difference in construction cost between the optimum designs with the substructures and with the entire structure was found to be small and thus the optimum design with the substructures,rnay conveniently be used in practical design. 5. The major active constraints of each structural member were found to be the tensile stress insteel for salb, the minimum lonitudinal steel ratio constraints for tower body and the shearing stress in concrete, tensile stress in steel and maximum eccentricityconstraints for footing, respectively. 6. The computer program develope in the present study can be effectively used even by an unexperienced designer for the optimum design of reinforced concrete intake-tower.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2009년 춘계학술대회논문집
• /
• pp.81-85
• /
• 2009

In this paper, the aerodynamic shape of air intake was investigated for the efficient cooling of electronic equipments in aircraft pod. As a first step, ESDU method was applied for the basic shape design of air intake considering the operational environments. The second step was to confirm the performance on design point, so the internal flow field of air intake was analyzed using a commercial Navier-Stokes code(FLUENT). And also the aerodynamic characteristics of internal flow at off-design condition was investigated with the variations of airflow rate. The results show that the air intake meets the requirement of target performance under the mission environments.

• 대한기계학회논문집B
• /
• 제25권8호
• /
• pp.1097-1102
• /
• 2001

For the purpose of development of high performance gasoline engine, the design technique of the 5-valve(3 intake valves) combustion chamber for a subcompact vehicle has been studied. 3 intake valves cylinder heads were designed by using a 3-dimension CAD program, and steady state flow experiments have been performed with these model. The 5-valve engines, which have larger valve opening areas, have larger intake flow rates and higher flow coefficient than the 4-valve engines. The effects of intake port design parameters of a 5-valve engine on the intake flow rate and bore size were studied, and the design guidelines for the 5-valve engine were established.

• 한국소음진동공학회논문집
• /
• 제15권6호
• /
• pp.680-686
• /
• 2005

This paper introduces the robust design of an intake system using transmission loss and the frequency weighting function. First, transmission loss is measured to evaluate the performance of the noise reduction for the intake system. The robust design parameters of the intake system are extracted by adapting a cost function with the Taguchi method. Subsequently, the frequency weighting function is developed by the subjective evaluation in which 6 special engineers were participated. Finally, the comparison between the proposed frequency weighted optimal design and unweighted optimal design for the transmission loss as the part is performed. Here, the overall levels of the transmission loss according to the methods are presented to validate the effectiveness of the proposed methodology.