• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2004년도 제22회 춘계학술대회논문집
• /
• pp.713-721
• /
• 2004

Variable air intake and variable exhaust nozzle of hypersonic engines are designed and tested in this study. Dimensions for variable geometry air intake, ram combustor and variable geometry exhaust nozzle are defined based on the requirements of a pre-cooled turbojet engine. Hypersonic Ramjet Engine is designed as a scaled test bed for each component. Actuation forces of moving parts for variable intake and variable nozzle are reduced by balancing the other force in the opposite direction. A demonstrator engine which includes variable intake and variable nozzle is designed and the components are fabricated. Composite material with silicone carbide is applied for high temperature parts under oxidation environment such as leading edge of the variable intake and combustor liner. Internal cooling structure is adopted for both moving and static parts of the variable nozzle. Pressure recovery and mass capture ratio of the variable intake at Mach 5 is obtained by a hypersonic wind tunnel test. Flow characteristics of the variable nozzle are obtained by a low temperature flow test. Wall temperature and heat flux of the nozzle at Mach 3 is obtained by a firing test. As results, the intake and the nozzle are proved to be used at designed pressure and temperature environment.

• 한국전산유체공학회:학술대회논문집
• /
• 한국전산유체공학회 2002년도 추계 학술대회논문집
• /
• pp.121-126
• /
• 2002

Aircraft propulsion systems often use diffusing S-duct to convey air flow from the wing or fuselage intake to the engine compressor, Well designed S-duct should incur minimal total pressure losses and deliver nearly uniform flow with small transverse velocity components at the engine compressor entrance. Reduced total pressure recovery lowers propulsion efficiency and nonuniform flow conditions at the engine face lower engine stall limits. In this study, S-duct which has maximum total pressure recovery and nearly uniform flow profiles at the compressure intake should be found using design optimization methods with 3-dimensional Wavier-Stokes analyses.

• 한국연소학회:학술대회논문집
• /
• 한국연소학회 제26회 KOSCO SYMPOSIUM 논문집
• /
• pp.7-12
• /
• 2003

The purpose of this work is to investigate the effect of premixing condition on the combustion and exhaust emission characteristics in a HCCI diesel engine. To form homogeneous charge before intake manifold, the premixed fuel is injected into premixed tank by GDI injection system and the premixed fuel is ignited by direct injected diesel fuel. But in the case of high intake air temperature, premixed fuel is auto-ignited before diesel combustion and soot emission is increased. In the case of light load condition, the BSFC is improved by intake air heating because increased air temperature promoted the combustion of premixed mixture. NOx and smoke concentration of exhaust emissions are reduced compared to conventional diesel engine. The combustion characteristics of the HCCI diesel engine such as combustion pressure, rate of heat release, and exhaust emission characteristics are discussed.

• 대한기계학회논문집
• /
• 제19권3호
• /
• pp.796-805
• /
• 1995

For the purpose of improving performances of a turbocharged diesel engine at low speed, this study investigates the effects of the injected air for the performances and flow characteristics in the intake and exhaust pipes by using the computer simulation with test bed. In the theoretical analysis, the whole flow system, including engine cylinders and intake and exhaust pipes, is calculated numerically by the method of filling and emptying. From the results of this study, the following conclusions may be summarized. Increasing injected air pressure into the pipe of compressor exit brings about the improvement in a performance and flow characteristics of intake and exhaust pipes under full load operating conditions at 1000 rpm of the engine speed, but shows trends of the inferior performances under no load operating conditions at 2000 rpm of the engine speed.

• 한국항공우주학회지
• /
• 제45권12호
• /
• pp.1031-1038
• /
• 2017

공기 흡입식 엔진의 성능 향상을 위하여 흡입구를 통한 유입공기의 전압력 회복률을 최대로 하는 것은 엔진 설계에 있어서 매우 중요하다. 흡입구의 각 램프 단에서 발생하는 충격파의 세기를 동일하게 흡입공기를 압축하면 흡입구에서의 최대 전압력 회복을 보장한다는 Oswatitsch 기법이 극초음속에서도 유효한지를 조사하였다. 극초음속 영역에서의 흡입구 작동 한계를 고려하여 압축 특성 및 열역학적 관점에서 유입 마하수에 따른 흡입구의 압축램프 각도와 램프 수에 따른 흡입구 성능을 비교하여 각단에서 발생하는 충격파 강도에 영향을 주는 경사 충격파에 수직한 마하수의 비선형성을 분석하였다. 이 분석을 근거로 Oswaitisch 기법이 초음속에서 뿐만 아니라 극초음속 비행 영역에서도 유효한 결과를 도출할 수 있음을 확인하였다.

• 항공우주시스템공학회지
• /
• 제16권1호
• /
• pp.81-85
• /
• 2022

본 연구에서 항공기 엔진의 공기흡입구 복합재 적용 구조 설계 및 해석 연구를 수행하였다. 본 연구에서 설계를 위해 대상 구조물의 구조 설계 요구조건 분석을 수행하였다. 구조 설계 하중은 압력 분포 하중과 가속도 조건을 적용하였다. 구조 설게 결과를 검증하기 위한 구조 안전성 평가를 위해 유한 요소 해석이 수행되었다. 구조 안전성 평가를 위해 응력 해석, 변형 해석, 좌굴 해석이 수행되었다. 최종 구조 안전성 검토를 통해 설계된 공기흡입구는 안전성을 확보한 것으로 확인되었다.

• 한국자동차공학회논문집
• /
• 제16권3호
• /
• pp.172-178
• /
• 2008

An object of this study is to confirm performance characteristics of the vortex tube apparatus for substitution of the intercooler in a common-rail diesel engine. The turbo pressure, the intake air flow rate and the ${\Delta}T_c$ decrease ratio of the intercooler were measured in a experimental engine. The vortex tube apparatus was made after confirmation of the geometric phenomena in fundamental experiments. To investigate energy separation characteristics of the vortex tube, the measured turbo pressure was applied to the vortex tube inlet and the ${\Delta}T_c$ decrease ratio was compared with one of the intercooler in the cold air mass flow ratio similar to the intake air flow rate of the experimental engine. From the results, we found that the energy separation ratio is increased according to of the inlet pressure and the ${\Delta}T_c$ decrease ratio of the vortex tube apparatus is higher than one of the intercooler at low engine speed and engine load of medium and low.

• 한국자동차공학회논문집
• /
• 제10권2호
• /
• pp.1-8
• /
• 2002

The flow and combustion patterns have been investigated inside the gasoline engine cylinder with the swirl or tumble flow, whereas the air flow characteristics, which are generated in the part of intake system before entering into the intake manifold, have not been known completely. It is necessary to analyze the flow field in the intake system consisting of air rater, throttle valve and intake manifold. The throttle valve, used to control the intake air flow rate, is important because it makes various mass flow rate and flow patterns. Three-dimen-sional How characteristics such as velocities, turbulent intensities and Reynolds shear stresses are measured by the hot wire anemometer at the exit of the throttle valve with the variation in the valve opening angle($15^{\circ}$, $45^{\circ}$, $75^{\circ}$ and $90^{\circ}$) and the Reynolds numbers (45000, 70000 and 140000). There are a lot of changes in flow characteristics at $75^{\circ}$ due to the large recirculation flow comparing with those of the other cases, and the streamwise velocity is especially enforced strongly below the valve shaft. The other component velocities are relatively large near the centerline parallel to the valve shaft. The effects of the Reynolds number on the flow field are not severe.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2011년도 제36회 춘계학술대회논문집
• /
• pp.132-135
• /
• 2011

초음속 흡입구의 충격파 안정성과 높은 압축효율을 획득하기 위한 버즈여유 결정기법을 제안하였다. 충격파 평형 방정식을 이용하여 자유흐름 및 배압에 의한 종말 충격파 위치의 민감도를 유도하였고, 외란의 크기를 통계적 방법에 의해 정량화 하였다. 수치적 계산결과 종말 충격파의 운동은 마하수에 비례하는 민감도 특성을 보였고, 후단 배압에 의한 그 영향이 가능 큰 것으로 나타났다.

• 한국항공운항학회지
• /
• 제23권3호
• /
• pp.8-17
• /
• 2015

In this research, low fidelity air/heat load analysis was conducted for the intake of high speed vehicle. For air/heat load calculations, aerodynamic properties at the surface and the boundary layer edge were estimated using Taylor-Maccoll equation for conical flow, shockwave relation and Prandtl-Meyer expansion equation for internal and external flow. Couette flow assumption and Reynolds analogy were used in order to calculate convective heat transfer coefficient. In order to calculate skin friction coefficient for heat transfer coefficient analysis, Van Driest method II and Reference Enthalpy method were considered. An axis symmetric SCRAMJET model was selected as a reference configuration for verifying the proper implementation of the present method. Comparison of the results using the present method and Computational Fluid Dynamic analysis showed that the present method is valuable for efficiently providing pressure and heat loads for air-intake structure design of the high speed air vehicle.