• 한국전기전자재료학회논문지
• /
• 제11권2호
• /
• pp.90-94
• /
• 1998

This study aims at analyzing to treeing in the solid-solid interface which is insulation type of cable junction parts, the proceeding of tree-growth and electrical breakdown were research in the study. Interface was made artificially to detect how it influenced the insulating ability of the whole system, the specimen were XLPE generally used in cable. The interface conditions were divided into two parts. First condition being the one focused on the surface of interface, it was treated with sand paper (#80, #600, #1200). For the second condition, the pressure of interface was varied as the value of 1, 5, 10 [$kg/cm^2$]. Using above conditions, treeing and breakdown properties on tree-growth were respectively compared in details. As a result, breakdown time was shorter for the full range of supplied voltage in the case of interface existed in the joint than non-existed interface. In the case of existed interface, the interface which had high-interface pressure and painted with silicon insulating oil was the best in the aspect of breakdown characteristics.

• Transactions on Electrical and Electronic Materials
• /
• 제6권6호
• /
• pp.294-300
• /
• 2005

According to the trend for electric power equipment of high capacity and reduction of its size, the needs for the new high performance electric equipments become more and more important. On of the possible solution is high temperature superconducting (HTS) power application. Following the successful development of practical HTS wires, there have been renewed activities in developing superconducting power equipment. HTS equipments have to be operated in a coolant such as liquid nitrogen ($LN_2$) or cooled by conduction-cooling method such as using Gifford-McMahon (G-M) cryocooler to maintain the temperature below critical level. In this paper, the dielectric strength of some insulating materials, such as unfilled epoxy, filled epoxy, and polyimide in $LN_2$ was analyzed. Epoxy is a good insulating material but fragile at cryogenic temperature. The filled epoxy composite not only compensates for this fragile property but enhances its dielectric strength.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2008년도 하계학술대회 논문집 Vol.9
• /
• pp.495-496
• /
• 2008

This paper describes the influence of Ultra-violet irradiation on time to tracking resistance of epoxy insulating materials by use of the inclined plane test. And, the influence of surface degradation was evaluated through several method such as measurement of contact angle, surface roughness, using a scanning electron microscopy. As the 1000 hours of the surface degradation with UV-CON, the flashover time decreases at different rates depending on epoxy resin and silicone rubber specimen. As the duration of the surface degradation with UV-CON is prolonged, the contact angle of epoxy resin decreases at the rate of degradation time, while that of silicone rubber was not exchanged. It is assumed that this phenomenon is related to the decrease in hydrophobicity of the surface of the materials. Also, as to epoxy resin, the decrease of hydrophobicity due to surface degradation with UV-CON is greater than that resulting from surface degradation with WOM. The UV radiation produced chalking and crazing on the surface of the insulating materials specimen.

• 한국전기전자재료학회논문지
• /
• 제33권4호
• /
• pp.286-290
• /
• 2020

The formation of inorganic thin films in low-temperature solution processes is necessary for a wide range of commercial applications of organic electronic devices. Aluminum oxide thin films can be utilized as barrier films that prevent the deterioration of an electronic device due to moisture and oxygen in the air. In addition, they can be used as the gate insulating layers of a thin film transistor. In this study, aluminum oxide thin film were formed using two methods simultaneously, a thermal process and the DUV process, and the properties of the thin films were compared. The result of converting aluminum nitrate hydrate to aluminum oxide through a hybrid process using a thermal treatment and DUV was confirmed by XPS measurements. A film-based a-IGZO TFT was fabricated using the formed inorganic thin film as a gate insulating film to confirm its properties.

• 한국전기전자재료학회논문지
• /
• 제37권1호
• /
• pp.56-62
• /
• 2024

By introducing curing kinetics and chemo-rheology for the epoxy resin formulation for ultra-high voltage gas insulated switchgear (GIS) Insulating Spacers, a study was conducted to simulate the curing behavior, flow and warpage analysis for optimization of the molding process in automatic pressure gelation. The curing rate equation and chemo-rheology equation were set as fixed values for various factors and other physical property values, and the APG molding process conditions were entered into the Moldflow software to perform optimization numerical simulations of the three-phase insulating spacer. Changes in curing shrinkage according to pack pressure were observed under the optimized process conditions. As a result, it was confirmed that the residence time in the solid state was shortened due to the lowest curing reaction when the curing holding pressure was 3 bar, and the occurrence of deformation due to internal residual stress was minimized.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 1995년도 하계학술대회 논문집 C
• /
• pp.1039-1041
• /
• 1995

This paper describes the performance of the widely used polymeric insulating material for outdoor insulation. Various methods to describe the surface aging of polymer materials such as the peak and average of the leakage current, the cumulative charge, the weight loss have been investigated. The relationship between surface current, time are plotted and discussed.

• E2M - 전기 전자와 첨단 소재
• /
• 제9권8호
• /
• pp.859-866
• /
• 1996

본 고에서는 절연재료에 대한 개괄적인 성질과 종류에 대해 간단히 설명하고 현재까지 개발되어 실용화 된 신 절연재료들을 소개하고자한다. 재료에 대한 연구는 절연재료 뿐만아니라 초전도재료, 극저온 재료등 특수한 성질을 갖거나 특수한 환경에서 특성을 유지할 수 있는 재료의 개발과 연구에 관심을 기울여야 할 시기라고 판단된다. 또한 기존의 재료에 대한 면밀한 재검토와 연구.고찰을 통해 보다 향상된 특성을 갖는 재료를 개발하는 것은 근본적으로 새로운 재료의 개발과 연구만큼이나 가치있는 일이라는 사실을 항상 명심해야 할 것이다.

• E2M - 전기 전자와 첨단 소재
• /
• 제11권11호
• /
• pp.17-21
• /
• 1998

The surface potential distribution on insulating polymers was measured by scanning of the probe of an electrostatic voltmeter. The measurements were done for two measured by scanning of the probe of an electrostatis voltmeter. The measurements were done for two cases. In the first case, it was measured on the free surface of insulating films which had been inserted between plane electodes after the removal of the upper brass disk electrode. In the second case, we measured the charging region between a circular and its opposing concentric ring electrodes after the removal of dc ramp voltage in air and nitrogen gas.

• 대한전기학회논문지
• /
• 제34권12호
• /
• pp.457-463
• /
• 1985

This paper studies on the tracking phenamena by the IEC recommended method with various polymeric insulating materials which are used in industrial fields. Under the same experimental condition, according to the materials it is observed that there are the type of tracking breakdown and the type of tracking erosion. In the tracking breakdown type materials, the tracking breakdown is occurred at a small number of drops increasing of test voltage and solution density. In the tracking erosion type materials, the erosion depth is saturated or proportioned as increasing of test voltage and solution density.

• 한국전기전자재료학회:학술대회논문집
• /
• 한국전기전자재료학회 2010년도 하계학술대회 논문집
• /
• pp.91-91
• /
• 2010

In this paper, nano composites material is produced by adding MgO with particle size of 5 [nm] into epoxy resign using as insulating material of power transformer apparatus and molding part to study the volume resistivity of nano composites used epoxy. We measured the volume resistivity using the High Resistance Meter(4329A) depending on changing the amount of addition and temperature in this experience. In result, we have confirmed that 1.0, 3.0, 5.0 and 10.0 [wt%] as about 2.9, 7.6, 7.5 and 6.1 times increased than virgin. Therefore, the characteristic of volume resistivity was relatively stable as specimen by added 3.0 [wt%] than the others.