• 설비공학논문집
• /
• 제10권5호
• /
• pp.619-629
• /
• 1998

An experimental work was conducted to investigate a feasibility of simultaneous measurement of gas-liquid two-phase flowrates with double orifice plates using air and water. The tests were carried out under the atmospheric pressure and at the ambient temperature using two different tube sizes. Qualities of an air-water flow in the present study have values less than 0.1 and thus the mixed flow showed bubbly, plug, slug flow regimes. The probability density function (PDF) and the power spectral density function (PSDF) of the instantaneous pressure drop traces for the flow regimes were obtained. It is found that some distinctive features exist in the distribution of these functions, depending upon the two-phase flow pattern. The time-averaged value of the instantaneous pressure drop increases with increasing gas and liquid flowrates, showing a single-valued function for the total mass flowrate and the quality. It is also found that the two-phase discharge coefficient exhibits a consistent trend for variation of dimensionless parameters such as the superficial velocity ratio and the gas Reynolds number. The results indicate that simultaneous measurement of two-phase flowrate may be possible based upon a statistical analysis of the instantaneous pressure drop curves monitored using double orifice plates.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 2001년도 춘계학술대회 논문집
• /
• pp.655-659
• /
• 2001

Resident time of the continuous and Instantaneous centrifugal separator using that separates the light and heavy liquids by use of density difference is the orptical factor that affects significantly the chemical metial extraction and the productivity in the chemical and mechanical process. In this paper, the overflow of the device is investigated under consideration of the relationships between inclination angle of liquid feeding screw and the centrifugal force. From the design of the length of a centrifugal separator, the radiuses of rotor and housing, theoretical formulation on the contact radius of separation weir is established through the experiments. From the experiments, it is identified that how much the capacity of inlet impeller and the emulsion phenomenon depend on the screw angle of inlet impeller. Also, we investigate the separation condition and the resident times that are functions of the phase ratio and density.

• 한국안전학회지
• /
• 제32권1호
• /
• pp.21-26
• /
• 2017

An IoT-based particulate matter (PM2.5) sensing device (PSD) is developed. The PSD consists of a PM2.5 sensor, signal processing circuit, and wi-fi enabled-microprocessor along with temperature and humidity sensors. The PSD estimates PM2.5 density by measuring light scattered by PM2.5. To gauge performance of the PSD, PM2.5 density of open air was measured with the PSD and compared with that of the collocated-government-certified measuring station. Measurements were taken at a sampling frequency of 100 Hz and moving-averaged to remove measurement noise. When compared to the result of the measuring station, average percentile error of PM2.5 density from the PSD is found to be 31%. A correlation coefficient is found to be 0.72 which indicates a strong correlation. Instantaneous variation, however, may far exceed average errors, leading to a conclusion that the PSD is more suitable for estimating average trend of PM2.5 density variations than estimating instantaneous PM2.5 density.

• 한국ITS학회 논문지
• /
• 제8권1호
• /
• pp.37-44
• /
• 2009

교통량, 속도, 밀도의 3가지 교통류 지표 중 밀도는 혼잡을 잘 나타내는 지표이다. 밀도를 측정하는 방안은 직접적으로 수집하는 방안과 수집자료를 활용하여 간접적으로 수집하는 방안이 있다. 직접적인 측정법은 대상구간의 교통류를 항공기나 고층건물에서 촬영하여 밀도를 직접적으로 구하는 것이나, 기상과 도로조건 및 비용상의 문제로 인하여 광범위한 사용에는 한계가 있다. 밀도를 간접적으로 측정할 수 있는 방안은 지점검지기를 이용하여 속도와 교통량을 측정하여 q=${\mu}k$식을 이용하여 밀도를 추정하는 방법이다. 하지만 이 역시 지점의 밀도값을 추정할 수 있을 뿐 구간의 밀도값을 대표할 수는 없다. 본 논문에서는 두 개의 지점검지기를 이용하여 밀도를 측정할 수 있는 방법을 제시하였다. 또한 순간밀도, 평균밀도, 측정간격이라는 개념을 정리하고 Paramics API 기능을 활용하여 자료를 생성한 후 측정간격이 밀도정확도에 미치는 영향을 분석하였다. 또한 밀도측정장비의 탑재를 위한 지수평활화 등의 프로세스가 포함된 밀도측정알고리즘도 제시하였다.

• 대한기계학회논문집A
• /
• 제24권12호
• /
• pp.3061-3071
• /
• 2000

Densification behavior of titanium alloy powder was investigated under hot pressing at various pressures and temperatures. Experimental date were obtained for densification of titanium alloy powder under an instantaneous loading and subsequent creep deformation during hot pressing. The constitutive models of Fleck et al. and the modified Gurson were employed for thermo-phastic deformation under the instantaneous loading and that f Abouaf and co-workers for creep deformation of titanium alloy powder during hot pressing. By implementing these constitutive equations into a finite element program(ABAQUS), finite element results were compared with experimental data during hot pressing. To investigate the effect of friction between the power and die wall, density distributions of power compacts were measured and compared with finite element calculations. Finite element results from the models of Fleck et al. and the modified Gurson agreed reasonably good with experimental data for densification and density distribution of titanium alloy powder under the instantaneous loading during hot pressing. Finite element results from the model of Abouaf and co-workers, however, somewhat overestimate experimental data for creep deformation of power compacts during hot pressing.

• 대한전기학회:학술대회논문집
• /
• 대한전기학회 2005년도 제36회 하계학술대회 논문집 B
• /
• pp.1447-1449
• /
• 2005

An interior permanent magnet synchronous motor(IPMSM) is receiving increased attention for many industrial applications because of its high torque to inertia ratio, superior power density, and high efficiency. This paper presents algorithm for speed sensorless vector control based on an Instantaneous Reactive Power. Effectiveness or algorithm is confirmed by the experiments.

• 대한설비공학회지:설비저널
• /
• 제17권5호
• /
• pp.590-597
• /
• 1988

Characteristics of flow regime transitions in inclined upwards gas-liquid two-phase flow have been investigated based upon a statistical analysis of instantaneous pressure drop curves through an orifice. The probability density functions of the curves indicate distinct patterns depending upon two-phase flow regime, which are very similar to those of horizontal two-phase. The dimensionless intensity of fluctuations of the pressure drops sharply change as the flow transitions such as plug-slug, pseudo slug-slug and annular-slug take place. The effects of inclination angle on the flow regime transitions have been also investigated. The results show that the method to identify the flow pattern based upon the statistical analysis of instantaneous pressure drops is suitable for inclined flow as well as horizontal flow.

• 대한교통학회지
• /
• 제20권5호
• /
• pp.67-79
• /
• 2002

교통량, 교통밀도, 교통류 속도 등, 교통류 변수에 대한 현재까지의 불확실한 정의와 연속적 파동방정식의 거시적 교통류 해석상의 문제점을 지적하고 이를 개선하기 위해 교통류 변수들에 대한 새로운 확률적 정의를 제시하고 이들의 성격을 규명하였다. 이러한 새로운 교통류 변수들에 대한 새로운 정의를 바탕으로 미시적 운전자 행동을 세밀하게 수용할 수 있고 많은 교통환경에서 연속적 파동 방정식을 대체하여 교통류 변수들과 통행시간을 예측할 수 있는 미분방정식 체계를 확률 미분방적식을 이용하여 도출하였다. 도출된 미분 방정식을 단일 차량의 시공 괘적에 적용해 보았다.

• 대한기계학회논문집B
• /
• 제24권4호
• /
• pp.504-511
• /
• 2000

PIV(Particle Image Velocimetry) is a recently developed technique for visualizing the fluid velocity fields. Because it has several advantages over the LDV(Laser Doppler Velocimetry), it became one of the most popular diagnostic tools in spite of its short history. However, its application to combustion is restricted by some problems such as flame illumination, scattered light refraction, particle density variation due to heat release, the combined effect of abrupt change in particle density and fluid velocity on flame contour, and thermophoresis which is particle lagging due to temperature gradient. These problems are expected to be originated from the non-continuous characteristics of flames and the limitations of particle dynamics. In the present study, these problems were considered for the visualization of the instantaneous coaxial hydrogen diffusion flame. And the instantaneous flame contour was detected using particle density difference. The visualized diffusion flame velocity field shows its turbulent and meandering nature. It was also observed that the flame is located inside the outer shear layer and flame geometry is largely influenced by the vorticity.

• 대한의용생체공학회:의공학회지
• /
• 제9권1호
• /
• pp.135-138
• /
• 1988

In this paper, computerized BEAM was implemented for the space domain analysis of EEG. Trans-formation from temporal summation to two-dimensional mappings is formed by 4 nearest point inter-polaton method. Methods of representation of BEAM are two. One is dot density method which classify brain electrical potential 9 levels by dot density of gray levels and the other is colour method which classify brain electrical 12 levels by red-green colours. In this BEAM, instantaneous change and average energy distribution over any arbitrary time interval of brain electrical activity could be observed and analyzed easily. In the frequency domain, the distribution of energy spectrum of a special band can easily be distinguished normality and abnormality.