• 한국태양에너지학회 논문집
• /
• 제35권4호
• /
• pp.25-34
• /
• 2015

This research is carried out to provide fundamental data for the design of solar photovoltaic systems. Methodologically, the solar radiation installations from 10 different pyreheliometers are measured, which are set up at 6 and 4 different levels of tilts and azimuth, respectively. Maximum of a yearly accumulated solar radiation is $1,569.8kWh/m^2{\cdot}year$ with a tilt angle of $30^{\circ}$ and an azimuth angle of $0^{\circ}$(south), $1,558.5kWh/m^2{\cdot}year$ with an azimuth angle of $0^{\circ}$(south) in combination of a tilt angle of $35^{\circ}$. This paper estimates that in designing fixed solar photovoltaic systems with a tilt angle of $12.5^{\circ}{\sim}50^{\circ}$(south) and a tilt angle of $35^{\circ}$ in combination of an azimuth angle of $S45^{\circ}W{\sim}S45^{\circ}E$, a tilt angle and an azimuth angle will cause a maximum 6.8% and 9.9% of efficiency variation respectively, depending on a installed solar module's angle and direction.

• 한국정보통신학회논문지
• /
• 제15권6호
• /
• pp.1238-1244
• /
• 2011

본 논문은 레이저 내비게이션의 위치측정을 위한 반사체 매칭방법을 제안하다. 레이저 내비게이션은 벽면에 부착된 반사체의 각도와 거리를 측정하는 장치이고 위치를 측정하기 위해서는 반사체의 매칭 기법이 필요하다. 대표적인 매칭 방법으로는 측정된 반사체의 위치를 이미 알고 있는 반사체의 위치로 평행 이동 한 후, 회전 하면서 매칭하는 방법이었다. 하지만 이 방법은 연산량이 많고 외란에 약하다는 단점이 있다. 이에, 본 논문에서는 연산량을 줄이고 외란에 강인한 반사체 매칭 방법을 제안한다. 제안된 방법은 계측된 반사체들의 위치를 설치된 반사체의 실제 위치로 생성한 후, 계측된 반사체들을 회전하면서 매칭하는 방법이다. 실험은 직접 설계한 AGV를 이용하였으며 조향각과 주행속도를 변화 시키면서 위치측정 정밀도를 비교하였다.

• KIEAE Journal
• /
• 제12권6호
• /
• pp.107-112
• /
• 2012

The purpose of this study is to determine the optimum slat angle of the venetian blind which was applied at an outer skin of a curtain-wall system. The evaluation of the blind slat angle was performed in terms of the comfortable visual environment and decreased energy consumption. The office building prototype was considered for the analysis and simulation variables include application of blind, blind slat angle and dimming control of lighting. The annual energy consumption and incidence rate of discomfort glare were analyzed using EnergyPlus which is developed by the U. S. Department of Energy for the detailed building energy simulation. As a result, it turns out that when the blind (reflectance: 0.5) was installed, the annual energy consumption was greater than that of the base model. However, when the dimming control was applied, the maximum energy saving of 16.3% could be achieved at a slat angle of $0^{\circ}$. In addition, in case of the base model, the incidence rate of discomfort glare was 84%, while the case of the blind with the slat angle of $0^{\circ}$ showed that the incidence rate of discomfort glare was 42.4%. Consequently, the results showed that the slat angle of $55^{\circ}$ with dimming control was the optimum strategy for the comfortable visual environment and decreased energy consumption.

• 한국기계가공학회지
• /
• 제10권4호
• /
• pp.44-49
• /
• 2011

The crawler crane, which consists of a lattice boom, a driving system, and movable vehicle, is widely used in a construction site. It needs to be installed an overload limiter to prevent the overturning accident and the fracture of structure. This research is undertaken to provide the relation formula for designing the overload limiter as follows: First the relation formulas between the wire-rope tension and the hoisting load or the overturning ratio according to the luffing angle and length of a lattice boom are established. Secondly the derived formulas are corrected by using the compensated angle considering the deflection of boom through the finite element analysis. The stiffness analysis is carried out for 30-kinds of models as a combination of 6-kinds of luffing angle and 5-kinds of length of boom. Finally the shape design of a stick type load cell, which is the device to measure the wire-rope tension, is performed. 5-kinds of notch radius and 5-kinds of center hole radius are adopted as the design parameter for the strength analysis of the load cell.

• 한국분무공학회지
• /
• 제15권3호
• /
• pp.115-123
• /
• 2010

The purpose of this study is to compare and to investigate spray characteristics of dimethyl ether (DME) and diesel fuel in the various injection pressures, ambient pressures, and the energizing durations. For the analysis of the spray characteristics, the spray visualization system including the high speed camera and the spray image analyzer is installed. The spray characteristics such as the spray development process, spray tip penetraion and the spray cone angle are analyzed from the spray images. It was revealed that the spray characteristics of DME and diesel fuels are mainly affected by the injection conditions. However, in the region after the end of the injection, the spray tip penetration was affected by the fuel properties such as the fuel density, the surface tension, and the viscosity. DME fuel has generally a short tip penetration and a wide cone angle. In the elevating conditions of the ambient gas pressure, the spray cone angle of DME fuel converged to high value when comparing diesel fuel in advance. Also, the increasing rate of the spray tip penetration in DME fuel is significantly decreased from 0.7 ms of the energizing duration (diesel : 0.9 ms).

• 천문학회보
• /
• 제43권1호
• /
• pp.72.2-72.2
• /
• 2018

The Opposition Effect (OE) is an enhancement of the brightness of a reflecting light as the phase angle (the Sun-target-observer angle) approaches zero. The mechanisms have been studied both theoretically and experimentally and nowadays recognized that there are two major mechanisms, namely, coherent backscattering OE (CBOE) and shadow hiding OE (SHOE). From data analyses of an S-type asteroid Itokawa taken with the Hayabusa spacecraft onboard camera, it is suggested that the CBOE would be dominant at phase angle smaller than ~ 1.4 deg, while SHOE dominates at larger phase angles (M. Lee & M. Ishiguro, under review). The study on the physical parameters which affect the OE, such as size and composition, will lead us to find a way to disentangle each of them from observation. The experiments in lab, however, faces two major difficulties: (a) the detector blocks the incident light if phase angle is nearly zero and (b) incident and emission angles must be controlled with high angular resolution to prevent blurring of OEs at different phase angles in one measurement. In this presentation, we introduce a new apparatus which has been installed at Seoul National University to investigate the OE in our lab, and summarize the initial results. It will be a valuable starting point to establish infrastructure in Korea, and will shed light on the investigation of OE physics using laboratory simulants.

• 설비공학논문집
• /
• 제24권6호
• /
• pp.461-466
• /
• 2012

Recently, building energy systems with solar collector and solar module have increased to improve energy problem, a heat island, a global warming and carbon dioxide emissions. In this study, value of solar radiation in areas was analyzed using TRNSYS simulation, and the optimum tilt and orientation angle for installing a photovoltaic module was examined. Average values of the weather data in the past twenty years in areas were used as input data. The results show that the tilt angle of a photovoltaic module for gaining the annual maximum solar radiation varies in different localities, and values of the annual solar radiation gained by using the variable photovoltaic module increased by 2.5 percent as compared with that gained by using the fixed photovoltaic module. When fixed photovoltaic module is installed, it should be examined the tilt and orientation angle for installing a photovoltaic module was examined.

• 한국군사과학기술학회지
• /
• 제20권4호
• /
• pp.497-504
• /
• 2017

This paper proposes a method to measure the airburst height by utilizing a high speed camera. This method might be applied to the test of which flight target is alive after the burst. The proposed method consists of four main steps. The first step is to compute the impact point using the sea surface height. The second step is to compute the height of burst (HOB) by using the distance from the camera to the impact point. This could be different from the real explosion height. That is because the distance from the camera to the burst point is not the same as it from the camera to the impact point. Therefore, the third step is to calculate the approach angle of the flight target with respect to the installed camera. Then, the last step is to compensate the computed height by using the approach angle. The result of the proposed method is compared with it from the triangulation. In this paper, the HOB error is also analyzed regarding the approach angle difference. Based on this analysis, the camera position might be suggested for error reduction.

• 한국기계가공학회지
• /
• 제20권3호
• /
• pp.83-91
• /
• 2021

A crawler crane, which consists of a lattice boom, a driving system, and a movable vehicle, is widely used on construction sites. The crawler crane often traverses rough terrain at these sites; as a result, an overload limiter needs to be installed on the crane to prevent it from overturning and breaking. In this paper, we studied the distributed load change in relation to boom length and the angle of rotation of the roller that comes in direct contact with the grounded track shoe. First, we developed a 3D model of a crawler crane and meshed it for finite elements. Then, we performed finite element analysis to derive the load on the roller. Finally, we graphed and examined the roller distributed load data of the case according to boom length and rotation angle. By detecting the load on the roller of the crawler crane, we can predict the potential for the crane to overturn before it happens.

• 한국공간구조학회논문집
• /
• 제22권1호
• /
• pp.25-32
• /
• 2022

The seismic behaviors of the arch structure vary according to the rise-span ratio of the arch structure. In this study, the rise-span ratio (H/L) of the example arch structure was set to 1/4, 1/6, and 1/8. And the installation angle of the seismic isolator was set to 15°, 30°, 45°, 60° and 90°. The installation angles of the seismic isolator were set by analyzing the horizontal and vertical reaction forces according to the rise-span ratio of the arch structure. Due to the geometrical and dynamic characteristics of the arch structure, the lower the rise-span ratio, the greater the horizontal reaction force of the static load, but the smaller the horizontal reaction force of the dynamic load. And if the seismic isolator is installed in the direction of the resultant force of the reaction forces caused by the seismic load, the horizontal seismic response becomes small. Also, as the installation angle of the seismic isolator increases, the hysteresis behavior of the seismic isolator shows a plastic behavior, and residual deformation appears even after the seismic load is removed. In the design of seismic isolators for seismic response control of large space structures such as arch structures, horizontal and vertical reaction forces should be considered.