• 한국산학기술학회논문지
• /
• 제16권6호
• /
• pp.3680-3684
• /
• 2015

조선소에서 데크 크레인은 지상에 설치된 타워 크레인이나 해상 크레인을 사용하여 리프팅 설치 방법에 의해 선박에 탑재된다. 데크 크레인의 두 점 리프팅 설치 작업 시에는 임시 고정 지그 등을 사용하는데, 안전한 리프팅 작업을 위해서는 고정 지그의 형상 및 설치 위치를 고려한 리프팅 안전성 평가가 선행되어야 한다. 본 연구에서는 데크 크레인 및 고정 지그에 해당하는 유한요소해석 모델을 각각 생성하고, 리프팅 반력 및 경계 조건을 적용한 구조 해석을 수행하여 리프팅 설치 작업에 대한 안전성을 평가하였다. 본 연구에서 제시한 안전성 평가 방법은 다양한 데크 크레인의 리프팅 설치 작업 시에 보다 안전한 리프팅 작업 가이드를 제공할 수 있는 해석적 툴로 활용될 수 있다.

• 조명전기설비학회논문지
• /
• 제29권4호
• /
• pp.108-115
• /
• 2015

This paper proposed a optimal current control method to improve efficiency of BLDC motors. The aim of the proposed method is to use the maximum torque operating method by increasing the effective voltage at the maximum torque point unlike existing SPM operating method. The proposed method is based on existing IPM maximum torque operating method grafting onto a square wave operating of SPM motors. As the method of increasing the effective output voltage from inverter using the maximum torque point, the proposed method is to improve efficiency of BLDC motors using the same amount of the existing current effectively. For this method, the maximum torque point is carried out by FEA and analysis of magnetic flux vector. In this paper, the prototype of general-purpose BLDC drive is manufactured and the performance characteristic and validity are verified.

• 조명전기설비학회논문지
• /
• 제26권8호
• /
• pp.56-64
• /
• 2012

This paper proposes a novel maximum power point tracking (MPPT) control algorithm considering radiation to improve efficiency of PV system. The proposed algorithm is composed perturb and observe (PO) method and constant voltage (CV) method. PO method is simple to realize and CV method is possible to tracking MPP with low radiation. Response characteristics of proposed algorithm are compared to conventional MPPT algorithm such as PO method, IC method and CV method with radiation variation. This paper proves the validity of proposed algorithm through the analysis results.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2005년도 춘계학술대회논문집
• /
• pp.3-7
• /
• 2005

A lighting method of our county is ordinary center concentration form. Therefore, it is usally used the Five Point Method, Multiplicity Method of KS, and Four Point Method of IES to measure a space illuminance. We can use the Five Point Method of KS when we measure a uniformity ratio or activities that happen in space is more sensitive than whole illumination. In addition, we can use the Multiplicity Method of KS and Four Point Method of IES when we measure whole illuminance like mean illuminance. Such method of measurements should be used exactly according to the kinds of space and activities.

• 조명전기설비학회논문지
• /
• 제29권12호
• /
• pp.40-46
• /
• 2015

This paper proposes the method which is improved a performance of PO MPPT control in PV system. The PO method is continually changed voltage toward direction that increases power, and if output power is decreased by changing voltage, a power of the conventional PO method is changed to a power before one step. These operations causes reduce of MPPT performance. Therefore, this paper proposes the MPPT method that can be improved the performance of the conventional PO method. When voltage is changed to direction of reducing power, the method proposed in this paper is changed to the voltage the opposite direction of twice step size. The MPPT performance of proposed method in this paper is compared with conventional PO method and proved the validity of this paper using these results.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2001년도 학술대회논문집
• /
• pp.167-172
• /
• 2001

본 연구는 저압간선의 굵기 산정에 있어서 체계적인 설계 흐름도를 분석하였고 Cable size별로 온도변화에 따른 직류 저항값 대비 교류 임피던스값의 변화에 대하여 전압강하를 고려한 간선의 선정기법을 제시 하였다.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2003년도 학술대회논문집
• /
• pp.289-290
• /
• 2003

This paper gives a method for the minimization of the fuel cost by optimal generation. Derivation of the sensitivity of system loss by optimization technique is introduced and the loss sensitivities are substituted into the optimality conditions to obtain the minimized fuel cost.

• KIEAE Journal
• /
• 제17권3호
• /
• pp.15-21
• /
• 2017

Purpose: "Building energy design standard" is used to limit the thermal transmittance of building in Korea. However, it only covers the insulation standard for each appropriate elements of a building, not the thermal performance of Junction thermal bridge of windows and doors installed in wall. Therefore in this study, we have evaluated the thermal performance of Junction thermal bridge depending on installation method and position of windows and provide it as design data. Method: We analyzed heat transfer of 4-Track sliding window and tilt & turn triple glazed window that are placed in the first class category on window energy efficiency rating using Window 7.4 and Therm 7.4. Result : First, linear thermal transmittance of 4-Track sliding window differs by 2.2 times or more depending of installation method and location. It is higher than the linear thermal transmittance, 0.01W/mK, proposed by Passivhaus. Second, linear thermal transmittance of Tilt & turn triple glazed window differs by 7.7 times or more depending of installation method and location. The average linear thermal transmittance was less than 0.01W /mK when windows were installed on the internal wall insulation by the fixed hardware attachment method. Third, the thermal losses of a window caused by a junction thermal bridge are inversely proportional to the window area and converge gradually as the area increased.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2007년도 추계학술대회 논문집
• /
• pp.31-37
• /
• 2007

The generation cost of photo voltaic is the most expensive among the renewable energy. To reduce the generation cost of photo voltaic, the proposed method added the regeneration power of elevator. Therefore we have the simulation results the proposed method is 60[%] higher than the previous photo voltaic generation for efficiency of generation.

• 한국조명전기설비학회:학술대회논문집
• /
• 한국조명전기설비학회 2002년도 학술대회논문집
• /
• pp.343-347
• /
• 2002

This paper analyzed the effect of breakdown electric current and it establishes a countermeasure that objective of the place where it put when with protection method which is applied from the existing electric railroad power supply system and where the protection method which is applied in the newly electrified system. Will reach and in order to attain simulation it did a actual power supply system and it analyzed that result.