• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.14 no.11
• /
• pp.1198-1206
• /
• 2003

In this paper, a MMIC waveguide mixer module based upon the novel suggested mode converter for wave-guide-to-microstrip transition was fabricated and measured. The insertion and return losses of the mode converter was optimized by compensating the discontinuity effect between ridge and microstrip with the modification of 50 $\Omega$ microstrip line pattern. Due to the low loss nature of the mode converter, a millimeter wave MMIC mixer chip can be successfully applied as a waveguide module for mmW waveguide communication system. The measured results of the module showed the successful MMIC chip application in waveguide and the negligible degradation of the supplied chip specification.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.22 no.2
• /
• pp.173-181
• /
• 2011

In this paper, we propose a half mode substrate integrated waveguide(HMSIW) balanced bandpass filter to yield improved isolation between output ports. In order to achieve good isolation, resistive coupling slot is employed in HMSIW filter. The measurement results show that the insertion losses($S_{21}$, $S_{31}$) are $5.4{\pm}0.2$ dB and input return loss($S_{11}$) is more than 10 dB from 5.8 GHz to 6.4 GHz. Moreover isolation between output ports is larger than 18 dB and phase difference of output ports is $180{\pm}10^{\circ}$.

• Proceedings of the KIEE Conference
• /
• 2000.07c
• /
• pp.1488-1490
• /
• 2000

ZnO:Cu thin films are deposited by using an RF magnetron co-sputtering system with Cu chips attached on ZnO target. Structural and electrical properties are analyzed as a function of deposition conditions, such as Cu chip areas, $O_2/(Ar+O_2)$ ratios, and working pressures, The results show that a higher electrical resistivity above $10^{10}$ ${\Omega}cm$ along with an excellent c-axial growth can be easily achieved by Cu-doping. SAW filters based on the ZnO:Cu films are also fabricated to estimate the electric-mechanical coupling coefficient($K^{2}_{eff}$). Higher $K^{2}_{eff}$ and lower insertion losses are observed for ZnO:Cu films, compared with those for ZnO films.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.45 no.7
• /
• pp.77-80
• /
• 2008

In this paper, low phase noise VCO using novel compact microstrip spiral resonator is proposed. A spiral resonator has super compact dimension, low insertion losses in the passband and high level of rejection in the stopband with sharp cutoff and a large coupling coefficient value, which makes a high Q value, and has reduced the phase noise. To increase the tuning range of VCO, varactor diode has been connected at the tunable negative resistance in VCO. This VCO has presented the oscillation frequency of $5.686{\sim}5.841GHz$, harmonics -29.83 dBc and phase noise of $-115.16{\sim}-115.17dBc/Hz$ at the offset frequency of 100 KHz.

• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.37 no.3
• /
• pp.49-57
• /
• 2000

In this paper, lumped-element isolator is analyzed and designed using the scattering matrix approach. Using the designed parameters, compact isolator with 7.0x7.0x2.3 mm$^3$ dimensions is fabricated and tested in 1.765GHz PCS phone band. Implemented isolator shows 29.95dB isolation characteristic at center frequency and has 0.35dB insertion loss in overall 30MHz operating bandwidth. Return losses of input and output port are measured below -19 dB. Experimental results show that the implemented isolator has better performances than the conventional one.

• The Journal of Korean Institute of Electromagnetic Engineering and Science
• /
• v.12 no.1
• /
• pp.27-36
• /
• 2001

In this paper, micromachined millimeter-wave cavity resonators ar presented. One-port and two-port cavity resonators at Ka-band are designed using 3D design software, HP $HFSS^{TM}$ ver. 5.5 Cavity resonators are fabricated on Si substrate, which is etched down for the cavity, bonded with a Quartz wafer in which metal patterns for the feeding line coupling slot are formed. One-port resonator shows the resonant frequency of 39.34 GHz, the return loss of 14.5 dB, and the loaded $Q(Q_{L})$ of 150. Two-port cavity resonator shows the resonant frequency of 39 GHz, the insertion and return losses of 4.6dB and 19,9dB, the loaded($Q_{L}$) and unloaded $Q(Q_{U})$) of 44.3 and 107, respectively.

• Journal of the Korea Institute of Information and Communication Engineering
• /
• v.16 no.5
• /
• pp.1029-1034
• /
• 2012

This paper presents a cost-effective and high-performance film bulk acoustic resonator (FBAR) duplexer module for US-PCS handset applications. The FBAR device uses a glass wafer level packaging process, which is a more cost-effective alternative to the typical silicon capping process. The maximum insertion losses of the FBAR duplexer at the Tx and Rx bands are of 1.9 and 2.4 dB, respectively. The total thickness of the duplexer module is 1.2 mm, including the glass-wafer bonded Tx/Rx FBAR devices, PCB board, and transfer molding material.

• ETRI Journal
• /
• v.40 no.6
• /
• pp.693-698
• /
• 2018

This paper presents a true-time delay (TTD) using a commercial $0.13-{\mu}m$ CMOS process for wideband phased-array antennas without the beam squint. The proposed TTD consists of four wideband distributed gain amplifiers (WDGAs), a 7-bit TTD circuit, and a 6-bit digital step attenuator (DSA) circuit. The T-type attenuator with a low-pass filter and the WDGAs are implemented for a low insertion loss error between the reference and time-delay states, and has a flat gain performance. The overall gain and return losses are >7 dB and >10 dB, respectively, at 2 GHz-18 GHz. The maximum time delay of 198 ps with a 1.56-ps step and the maximum attenuation of 31.5 dB with a 0.5-dB step are achieved at 2 GHz-18 GHz. The RMS time-delay and amplitude errors are <3 ps and <1 dB, respectively, at 2 GHz-18 GHz. An output P1 dB of <-0.5 dBm is achieved at 2 GHz-18 GHz. The chip size is $3.3{\times}1.6mm^2$, including pads, and the DC power consumption is 370 mW for a 3.3-V supply voltage.

• Journal of the Korea Society for Simulation
• /
• v.30 no.3
• /
• pp.31-39
• /
• 2021

During artillery fire, an excessive level of impulse noise propagating in the form of a storm wave is generated. Since the sound of impact from the fire affects the stability of the surrounding structures, the artillery and the structures must be separated from each other by the proper distance to avoid damages from friendly fire. However, if they have already been built within the distance, it is possible to prevent the damages by building sound barriers between them. In this study, the proper separation distance between the artillery and the structure was calculated, and the insertion losses due to various heights and shapes of the sound barrier were simulated by using the BEM(Boundary Element Method), and conclusively the optimal sound barrier was selected.

• ETRI Journal
• /
• v.45 no.2
• /
• pp.338-345
• /
• 2023

A filtering power divider based on air-filled substrate-integrated waveguide (AFSIW) technology is proposed in this study. The AFSIW structure is used in the proposed filtering power divider for substantially reducing the transmission losses. This structure occupies a large area because of the use of air as a dielectric instead of typical dielectric materials. A filtering power divider provides power division and frequency selectivity simultaneously in a single device. The proposed filtering power divider comprises three AFSIW cavities. The filtering function is achieved using symmetrical inductive posts. The input and output ports of the proposed circuit are realized by directly connecting coaxial lines to the AFSIW cavities. This transition from the coaxial line to the AFSIW cavity eliminates the additional transitions, such as AFSIW-SIW and SIW-conductor-backed coplanar waveguide, applied in existing AFSIW circuits. The proposed power divider with a second-order bandpass filtering response is fabricated and measured at 5.5 GHz. The measurement results show that this circuit has a minimum insertion loss of 1 dB, 3-dB fractional bandwidth of 11.2%, and return loss exceeding 11 dB.