• 유체기계공업학회:학술대회논문집
• /
• 2006.08a
• /
• pp.327-330
• /
• 2006

This paper represents the numerical analysis on effects of radius ratio in a concentric annulus with a rotating inner cylinder. The numerical model consisted of two cylinder which inner cylinder is rotating and outer cylinder is fix, and the axial direction is used the cyclic condition because of the length for axial direction is assumed infinite. The diameter of inner cylinder is assumed 86.8mm, the numerical parameters are angular velocity and radius ratio. Also, the whole walls of numerical model have no-slip and the working fluid is used water at $20^{\circ}C$. The numerical analysis is assumed the transient state to observe the flow variations by time and the 3-D cylindrical coordinate system. The calculation grid adopted a non-constant grid for dense arrangement near the wall side of cylinder, the standard $k-{\omega}$ high Reynolds number model to consider the effect of turbulence flow and wall, the fully implicit method for time term and the quick scheme for momentum equation. The numerical method is compared with the experimental results by Wereley and Lueptow, and the results are very good agreement. As the results, TVF isn't appeared when Re is small because of the initial flow instability is disappear by effect of the centrifugal force and viscosity. The vortex size is from 0.8 to 1.1 for TVF at various $\eta$, and the traveling distance for wavy vortex have the critical traveling distance for each case.

• Journal of the Korean Institute of Rural Architecture
• /
• v.13 no.3
• /
• pp.83-90
• /
• 2011

The purpose of this study is to analyze size and proportion of plan and section, and derive characteristics by types of worship-space in central hall of buddhist temple. This study covers 45 buddhist temples as designated national treasure and treasure. Types of central hall of buddhist temple are 'Columnless Type', 'Inner Column Type', and 'Colonnade Type'. The results are as follows. Firstly, in the proportion of width and length, 'Columnless Type' is mostly represented with 1:0.73, 'Inner Column Type' with 1:0.54 and seems to be widening for the other types, and 'Colonnade Type' is same proportion with 'Columnless Type'. Secondly, in the proportion of width and height, 'Columnless Type' is 1:0.61 and sizes of worship-space of this type are different but the proportion is same. In the 'Inner Column Type', worship-space is enlarged because a buddhist altar is hustled into the rear. Thirdly, in the proportion of length and height, all types are represented with similar proportion as 1:1. Finally, proportion of the volume of worship-space in 'Columnless Type' is 1(width):0.74(length):0.60(height). The case of 'Inner Column Type' is 1:0.57:0.57 and length of worship-space is shortened, so characteristics of horizontality is emphasized. The space of same size with the proportion of 'Columnless Type' is situated in the inside of worship-space in 'Colonnade Type'.

• Journal of the Korean Society of Industry Convergence
• /
• v.25 no.4_2
• /
• pp.637-644
• /
• 2022

In this study, the flow characteristics according to the shape of the vortex nozzle was studied by numerical analysis and the amount of microbubble generation was measured experimentally. The shape of the vortex nozzle is cylindrical, diffuser, and conical type. The axial fluid velocity in the induced tube gradually increased from the inlet to the outlet. In particular, the fluid velocity in the nozzle part increased rapidly. The velocity distribution of the fluid at the inlet of the induced tube showed that the flow rotates counterclockwise in the outer region and the inner center of the induced tube. At the outlet of the induced tube, the cylindrical and conical type showed rotational flow, and the diffuser type showed irregular turbulent flow. The dimensionless pressure ratio 𝜂 of the inner region of the induced tube was lower than that of the outer region. Also, 𝜂 near the outlet of the induced tube in cylindrical and conical type showed a similar tendency to the inlet area. At the outer region of inlet of induced tube, intense vorticity was observed on the wall and in lower region. At the inner region of inlet of induced tube, intense vorticity was observed on the inner wall of the induced tube and in the central region of the inlet of the induced tube. At the outlet of induced tube, in the case of the cylindrical and conical type, intense vorticity was observed near the inner wall, the diffuser type showed irregular strong vorticity inside the tube. The total number of bubbles measured was the most in the cylindrical type, and the microbubbles less than 50mm occurred the most in the conical type.

• Korean Institute of Interior Design Journal
• /
• v.24 no.1
• /
• pp.160-168
• /
• 2015

The subject of this research is to analyze the design characteristics of outdoor spaces in Good Design awarded apartment complexes in the past decade. The results are as follows. First, the overall outdoor space design theme, one of the conceptual elements, is focused on both 'nature' and 'story of various subject' that are similar to each other. Second, the case study object with the visual openness, which is secured between apartment blocks, is shown frequently in case box-shaped apartment blocks are arranged in a row. However, in case of Y-shaped block arrangement, the visual openness secured within an apartment complex is considered more important. Third, according to the result of circulation/ inner path element, the most frequently appeared inner path form is a grid pattern with straight path emphasis. While apartment complexes with the parking lot on the ground are only 3 out of 18 cases, it with circulation path for vehicle on the ground level are over 61%. Fourthly, the design characteristic of social space of physical outdoor design appears to be 'central link facility type'. In this case, the central community facilities are more likely to be combined with various functions, such as green, water, and social connection. Fifthly, in case of natural space, most of the apartment cases are shown over 45% green area ratio with wide green and water space provision. Especially, the differentiation is to provide the space where can stimulate a resident's participation.

• Journal of Chest Surgery
• /
• v.27 no.2
• /
• pp.153-156
• /
• 1994

Bentall`s operation for repair of annuloaortic ectasia has been associated with postoperative bleeding and with false aneurysm of the anastomotic site between the coronary orifice and composite graft.Among 5 cases, 2 cases have been operated direct anastomosis between coronary artery and vascular graft.Remained 3 cases have been operated with doughnutlike Teflon felt buttress.The technique of sandwiching the freed button of aortic wall bearing the coronary artery ostium between an outer Teflon felt doughnutlike buttress and the inner composite graft provides a leak-proof anastomosis.We experienced one case reoperation for bleeding at coronary anastomotic site above method.

• The Journal of the Institute of Internet, Broadcasting and Communication
• /
• v.13 no.4
• /
• pp.201-208
• /
• 2013

This paper is a study of an empirical design of an open-ended coaxial cavity resonator. It can be done by using the radius of the inner conductor, the inner radius and the length of the resonator. However, the basic coaxial transmission -line theory can be seen that the characteristics of the resonant frequency and the Q value are varied by the change of length, regardless of the value of radius of the inner conductor and inner radius of the resonator. We find out the impact of radius of the inner conductor, inner radius of the resonator and the length of the resonator parameter and propose the optimized empirical resonator design method by reducing the error between the theoretical value and the design value. Based on the simulation, several resonators are fabricated by the size of 14 mm for the radius of inner conductor, 2 mm, 5 mm, 10 mm respectively for the inner radius of resonator, and 8.5 mm for the length of the resonator. The resonant frequencies of the produced resonators were measured at 6.1, 5.7, 6.5 GHz respectively. According to the result of simulation and measurement, we know that we can design the relatively exact open-ended coaxial cavity resonator by applying the basic coaxial transmission-line theory directly when the length of the resonator is less than 10 mm, and adding the correction factor of 0.5 GHz to the calculated resonant frequency in case of more than 10 mm of the length of the resonator.

• The korean journal of orthodontics
• /
• v.34 no.2 s.103
• /
• pp.121-129
• /
• 2004

The purpose of this study was to photoelastically visualize 4he distribution of fortes transmitted to the alveolus and surrounding structures using three different types of headgear for the distal movement of the upper molars. A photoelastic maxillary model was made and three different directional forces applied, which were high-pull, straight-pull, and cervical-pull. Stress distribution was recorded through circular polariscope, and two-dimensional photoelastic stress analysis was performed according to isochromatic fringe characteristics. The results were as follows: 1. In the case of high-pull headgear bodily movement occurred in the medium- length outer bow, stress distribution in the apical region was 1st molar, 2nd premolar, lst premolar in sequence and there was no apparent difference. 2. In the case of straight-pull headgear, bodily movement occurred in the long outer bow and stress distribution in the apical region was heavy in the 1st molar, 2nd premolar, 1st premolar in sequence. But. there were no apparent differences according to the length of the outer bow. 3. In the case of cervical- pull headgear, bodily movement also occulted in 4he long outer bow, and apical stress of the premolar region was heaviest among other cases and apical stress of the 2nd premolar was heaviest in the short outer bow. In clinical situations, to achieve bodily movement of the upper 1st molars without modifying outer bow height, applying an outer bow length as long as the inner bow length in high-pull headgear and applying an outer bow length longer than the inner bow length in straight-pull, cervical-pull headgear are recommended.

• Proceedings of the Korean Society of Precision Engineering Conference
• /
• 1997.04a
• /
• pp.303-306
• /
• 1997

In the case of a cooled air cooling applied to angular contact ball bearings in a high speed spindle unit,the heat generated heat in bearings is removed and the temperature of inner ring is decreased.. Therefore it is possible to increase the speed of spindle units.

• Congress of the korean instutite of fire investigation
• /
• 2010.12a
• /
• pp.137-145
• /
• 2010

• Archives of Pharmacal Research
• /
• v.21 no.6
• /
• pp.645-650
• /
• 1998

The dual drug-loaded alginate beads simultaneously containing drug in inner and outer layers were prepared by dropping plain (single-layered) alginate beads into $CaCl_2$ solution. The release characteristics were evaluated in simulated gastric fluid for 2 h followed by intestinal fluids thereafter for 12 h. The surface morphology and cross section of dual drug-loaded alginate beads was also investigated using scanning electron microscope (SEM). The poorlv water-soluble ibuprofen was chosen as a model drug. The surface of single-layered and dual drug-loaded alginate beads showed very crude and roughness, showing aggregated particles, surface cracks and rough crystals. The thickness of dual drug-loaded alginate beads surrounded by outer layer was ranged from about 57 to 329mcm. The distinct chasm between inner and outer layers was also observed. In case of single-layered alginate bead, the drug was not released in gastric fluid but was largely released in intestinal fluid. However, the release rate decreased as the reinforcing $Eudragit^{\circledR}$ polymer contents increased. When the plasticizers were added into polymer, the release rate largely decreased. The release rate of dual drug-loaded alginate beads was stable in gastric fluid for 2 h but largely increased when switched in intestinal fluid. The drug linearly released for 4 h followed by another linear release thereafter, showing a distinct biphasic release characteristics. There was a difference in the release profiles between single-layered and dual drug-loaded alginate beads due to their structural shape. However, this biphasic release profiles were modified by varying formulation compositions of inner and outer layer of alginate beads. The release rate of dual drug-loaded alginate beads slightly decreased when the outer layer was reinforced with $Eudragit^{\circledR}$ RS1OO polymers. In case of dual drug-loaded alginate beads with polymer-reinforced outer layer only, the initial amount of druc released was low but the initial release rate (slope) was higher due to more swellable inner cores when compared to polymer-reinforced inner cores. The current dual drug-loaded alginate beads may be used to deliver the drugs in a time dependent manner.