• 대한설비공학회:학술대회논문집
• /
• 대한설비공학회 2009년도 하계학술발표대회 논문집
• /
• pp.1491-1496
• /
• 2009

Fluid flow and structural analyses of an electronic expansion valve (EEV) using CO2 as a working refrigerant are carried out to estimate the mass flow rate and maximum stress. An engineering sample EEV that the orifice diameter is 1.8 mm was fabricated. The mass flow rates were measured at various EEV inlet temperatures and pressures for several EEV openings using experimental heat pump system. The sample EEV has over 35 MPa burst pressure and the maximum mass flow rate of CO2 through the EEV increased to 100 g/s at full opening condition.

• 한국정밀공학회지
• /
• 제34권1호
• /
• pp.59-63
• /
• 2017

We present a multi-sample array device based on a pneumatic system. Solenoid valves were used to control a micro valve in a pneumatic system. The use of a compressor together with a vacuum pump ensured that one outlet could supply both compression and vacuum pressure. The multi-sample array device was fabricated using conventional photolithography and PDMS casting. The device was composed of a multiplexer, sample array, and rinsing. The multiplexer could control four sample solutions injecting into the sample array chamber. Sample solution not arrayed was removed by DI-water from the rinsing inlet. To prevent trapping of microbubbles in the channel during injection of sample solution into the device, surfactant was added in PDMS solution to serve as a hydrophilic surface treatment. As a result, the device could be used as a sample array for 64 cases, using four samples and three columns of three chambers.

• 한국신재생에너지학회:학술대회논문집
• /
• 한국신재생에너지학회 2007년도 추계학술대회 논문집
• /
• pp.188-191
• /
• 2007

This paper shows the Development of In-tank pressure regulator and Solenoid Valve used in FCV(Fuel Cell Vehicle). We have developed new type of Regulator and Solenoid through analysis of the structure and characteristics of component of FCS(Fuel Cell System) from the advanced technology. Now it is possible to localize the component by making use of the development of Regulator and Solenoid made by us. Regulator and Solenoid is a equipment to control hydrogen pressure supplied into a stack. Therefore, outlet pressure, a flow of fluid and temperature are important parameters according to a inlet pressure. And leak test, endurance test and burst test should be done to guarantee the performance and safety of Regulator and Solenoid used in the fuel of high pressure. Also, Hydrogen friendly materials are applied to inner parts of the Regulator, Solenoid and weight reduction is done to cost saving in part not related to performance. As a result, we have proven the good performance and reliability in endurance of Regulator, Solenoid and will make an development in performance as well as durability to ensure industrialization.

• 한국분무공학회지
• /
• 제9권2호
• /
• pp.9-17
• /
• 2004

The performance characteristics of lean burn system in gasoline engine are mainly affected by the air-fuel mixture in cylinder, gas exchange process of manifold system, exhaust emission of engine, and the electronic engine control system. In order to obtain the effect of performance factors on the optimum conditions of lean burn engine, this study deal with the behavior of mixture formation, gas flow characteristics of air, flow and evaporation analysis of spray droplet in cylinder, vaporization and burning characteristics of lean mixture in the engine, and the control performance of electronic engine control system. The optimum flow conditions were investigated with the swirl and tumble flows in the combustion chamber with swirl control valve. The performance characteristics and optimum condition of flow field in intake system were analyzed by the investigation of inlet flow of air and combustion stabilization on cylinder.

• 대한의용생체공학회:의공학회지
• /
• 제18권2호
• /
• pp.147-156
• /
• 1997

Various prosthetic heart valves have been developed and used clinically, but they have problems, such as thrombogenecity, hemoltsis, high cost and low durability. New types of trileaflet polymer heart valves have been developed in order to use them as inlet and outlet valves in a ventricular assist device. The aim of this study is to determine the hydrodynamic effectiveness of the newly designed trileaflet polymer valves and their feasibility for temporary use in the blood pumps. Trileaflet polymer valves are made of polyurethane, because of its good blood compatibility, high tonsil strength and good resistance to fatigue. An in vitro experimental investigation was perf'ormed in order to ev91ua1e hydrodynamic performance of the trileaflet polymer valves having different design and fabrication tech- niques. The St. Jude Medical valve (SJMV) and floating-type monoleaflet polymer valve (MLPV) were also tested The pressure drop across the valve, leakage volume, and the flow patterns mere investigated for valves. The result of comparative tests showed that the trileaflet polymer valves had a better hydrodynamic performance than the others. TPV which has two stable membrane shape showed the lowest back flow. The pressure hops of TPVs were lower than that of MLPV, but slightly higher than SJMV. The hydrodynamic performance of valves under the pulastile flow showed the similar results as steady flow. The velocity profiles and turbulent intensities were measured at the distal sites of valves using a hot-film anemometer. Central flow was maintained in trileaflet polymer valves, and the maximum turbulent intensities were lower in TPVs comparing to MLPV.

• 한국추진공학회:학술대회논문집
• /
• 한국추진공학회 2010년도 제35회 추계학술대회논문집
• /
• pp.111-114
• /
• 2010

발사체 추진시스템에서 CC(Combustion Chamber) 산화제 개폐밸브는 액체산소를 연소기로 공급 및 차단함으로써 연소를 개시 및 중단시킬 뿐만 아니라, 정상운영 상태에서는 연소기 내 안정된 연소가 가능하도록 일정한 유량의 액체산소를 공급한다. 개발이 완료된 산화제 개폐밸브 EM(Engineering Model)의 주요 구성부의 성능향상을 위하여 전산구조해석을 이용한 중간플랜지, 밸브 입구의 립 부분의 설계 변경을 수행하였으며, 성능 시험을 통하여 설계변경에 의한 성능 향상을 최종확인 하였다.

• 에너지공학
• /
• 제11권1호
• /
• pp.26-33
• /
• 2002

본 연구에서는 butterfly valve주위의 비압축성 및 압축성유동 특성을 수치해석을 통하여 조사하였다. 밸브는 문제를 단순화시키기 위하여 평판 디스크로 간주하였으며, 다양한 디스크 각도 및 압력비 변화에 대한 계산을 수행하였다. 각도가 증가함에 따라 디스크 상류면의 정체점은 디스크의 중심으로 이동하는 것을 볼 수 있었고, 입구공기의 유입 속도는 감소함을 볼 수 있었다. 최고 유속은 디스크와 벽면사이에 형성되는 vena contracta 효과에 의해 생기는 목의 하류에서 형성됨을 볼 수 있었다. 압력비를 감소함에 따라 압축성 효과는 증대되며 유동이 초음속화 되면서 생성되는 강한 wall jet에 의해 shock cell structure가 형성되는 것을 볼 수 있었다. 입구유량은 디스크 각도와 압력비의 증가에 따라서 감소하며, 압력손실계수는 디스크 각도의 증가 및 압력비의 감소에 따라 증가하였다.

• 한국정보전자통신기술학회논문지
• /
• 제14권5호
• /
• pp.369-374
• /
• 2021

최근에 건설되는 아파트는 주방이 빌트인 방식으로 만들어지므로 가스 호스가 싱크대 내부에 보이지 않게 만들어지므로 가스가 누출될 경우 싱크대 내부에 축적되어 가스 폭발로 이어질 수 있는 위험한 방식이다. 본 연구에서는 가스레인지와 중간밸브 사이에 연결된 호스가 싱크대 내부에 있어 가스 누출 검사를 할 수 없는 구조로 되어 있어 압력센서를 이용하여 가스누출을 검사를 쉽게 할 수 있는 밸브 시스템 연구하였다. 압력 측정 방법은 중간밸브와 가스레인지를 연결하는 호스의 압력을 측정하여 I2C통신 방식으로 데이터를 수집·분석 할 수 있도록 진행하였다. 또한 가정에 공급되는 가스압력계산은 대기압력에 가스계량기의 입구에서 가스게이지 압력 평균값 22.46mbar를 더 한 값으로 계산된 것에 대한 대기 압력 오차에 대한 규명 및 미세한 가스 누출 감지를 할 수 있도록 밸브 시스템을 개발하였다.

• 대한기계학회논문집B
• /
• 제37권9호
• /
• pp.863-871
• /
• 2013

본 수치적 연구에서는 국내의 발전소에서 사용되는 일반적인 고차압 트림의 형상 중 대표적으로 사용되는 형상의 트림을 기본형 트림으로 정하여, 이를 설계한 후 캐비테이션과 유량의 관점에서 유동 특성을 살펴보았다. 실제로 운전되는 발전소계통의 운전조건을 참고하여 고차압 조건으로서 입 출구 차압을 18.7 MPa로, 온도를 $160^{\circ}C$로 설정하였다. 트림의 주요 설계 인자로서 유로의 면적, 유로의 단(stage)과 유로의 방향을 채택하여, 유량과 케비테이션 발생 특성을 개선하기 위해 기본형 트림을 재설계하였다. 개선을 위해 트림을 반경방향으로 세 영역으로 나눈 후 각 영역에서 재설계 인자를 이용하여 형상을 변경하였다. 4가지의 재설계 모델을 제안하였으며, 각 모델 형상에 대한 수치해석을 수행하였다. 유량 및 캐비테이션 발생량의 관점에서 기본형 트림과 설계개선 트림들을 비교하여 재설계 모델의 성능이 개선되었음을 확인하였다.

• 대한안전경영과학회지
• /
• 제17권4호
• /
• pp.161-169
• /
• 2015

A fire sprinkler system is very important to extinguish fire in the building. The sprinkler system initiates sprinkler discharge if the detection system identifies a developing fire and opens the pre-action valve. However, pre-action fire sprinkler systems mainly installed in the underground parking lot at the apartment complex do not properly operate at fire if the connection type of fire sprinkler systems does not properly installed and operated. This study identified the relationship between fire dispersion & damage and the connection type of water supply in the sprinkler system from many fire cases at the apartment complex in South Korea. In addition, this study also identified the water supply differences and characteristics between South Korea and foreign countries. The main purpose of this study is also to improve the water connection types in the sprinkler system that can reduce the potential failures of pre-action valve operation through electrical signal system. The study also suggests the improvement plan for water connection types in pre-action fire sprinkler system that can minimize potential failure of pre-action fire sprinkler system. The suggestions for revising the fire safe standard in South Korea includes letting the water supply pipe of sprinkler system water inlet connect to the second side of pre-action valve and the water flow device that can minimize potential failure of sprinkler system.