• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.50 no.5
• /
• pp.297-308
• /
• 2022

Most air-breathing aircraft operated in the hypersonic region are equipped with a scramjet engine. In a scramjet engine, a shock wave generated at an inlet acts as a compressor for a general gas turbine engine instead, so total pressure loss caused by the shock wave is considered very important. In this study, to minimize total pressure loss, a method of designing an external compression inlet using isentropic compression surface was proposed, and an external compression inlet with 3-deflection angles and Busemann inlet were designed under the same conditions. After that, through computational analysis, the performance characteristics at off-design conditions were compared. Each inlet shape was truncated according to the length of the 3-ramp external compression inlet, and the boundary layer correction was performed. The isentropic external compression inlet showed superior performance at the design point, but under the off-design conditions, its performance was degraded compared to the 3-ramp external compression inlet.

• The KSFM Journal of Fluid Machinery
• /
• v.15 no.2
• /
• pp.57-62
• /
• 2012

The constant air volume flow fan can maintain constant flow rate to the wide range of exit pressure. Therefore, the use of this fan is increasing recently for ventilation of high building. Brushless DC motor is adopted to this fan because that has advantages of compactness and performance. But this type of motor protrude from impeller hub side to fan inlet. The Impeller inlet flow is influenced by size of this obstacle called hub. In this paper, the influence of hub shape on the fan performance characteristics are experimentally and numerically analyzed. CFX 12.0 is used to perform the fan internal flow analysis and numerical results are compared with the experiments. Depending on hub shape, internal loss is generated and the performance and efficiency are reduced. The best performance is occurred around $h/b_1$ = 0.25. The results of this study will be contribute to initial design of constant air volume flow fan development.

• Food Science and Biotechnology
• /
• v.14 no.6
• /
• pp.747-751
• /
• 2005

Microencapsulation of pine flavors was investigated to determine the optimum wall material and spray drying condition. ${\beta}$-Cyclodextrin, maltodextrin, and a 3:1 mixture of maltodextrin and gum arabic were evaluated as wall materials. The latter mixture was determined to be the best wall material based on dispersion capacity and flavor yield. Spray drying effectiveness was evaluated using a $3^3$ fraction factorial design and statistical analysis. The optimum operation condition was an inlet air temperature of $175^{\circ}C$, inlet airflow rate of $0.65\;m^3/min$ and atomizing pressure of 180 kPa, which resulted in a 93% flavor yield. The best particle shape observed by SEM was a round globular shape obtained under the above spray drying condition, whereas lower temperatures and higher inlet airflow rates resulted in initial and full collapses, respectively. The round globular shapes remained stable for at least one month.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.21 no.5
• /
• pp.59-66
• /
• 2013

Lack of the space in many diesel vehicles make it difficult to design and install the catalytic muffler to reduce emissions. For this reason, inlet part of the catalytic muffler is made of L-type which has lower flow uniformity than conventional I-type, and catalytic muffler has complex internal structure by various insertions, which affect the flow uniformity and pressure drop of the systems. In this work, the flow characteristics such as flow uniformity and pressure drop have been numerically investigated by changing such various geometries as inlet shape, porosity, and outlet shape inside the muffler with the three-dimensional turbulent incompressible flow solver. Total 4 different cases are considered in order to find optimal configurations of the catalytic muffler in view of high flow uniformity and low pressure drop. The results show that Case 2 which has no induction cone and outlet perforated pipe has higher uniformity index and lower pressure drop than others considered in this work.

• The KSFM Journal of Fluid Machinery
• /
• v.17 no.1
• /
• pp.28-34
• /
• 2014

This paper presents the performance enhancement of a double-inlet centrifugal blower by the shape optimization of an impeller. Two design variables, a number of blade and a length of chord, are introduced, and analyzed by a response surface method. Three-dimensional compressible Navier-Stokes equations are used to analyze the blower performance and the internal flow of the blower. Throughout the numerical simulation of the blower, blower efficiency can be increased by reducing separation flow generating from the blade leading edge of a blade pressure surface. It is noted that recirculation flow observed inside the blade passage induces low velocity region, thus increases pressure loss. Efficiency and pressure of the optimum blower are successfully increased up to 3% and 3.9% compared to those of reference blower at the design flow condition, respectively. Detailed flow field inside the blower is also analyzed and compared.

• Journal of the Korean Institute of Gas
• /
• v.16 no.1
• /
• pp.1-7
• /
• 2012

The present study has been carried out to analyze the flow characteristics in the inlet expasion duct of a heat recovery steam generator by using numerical flow analysis. The inlet of HRSG corresponds the outlet of gas turbine exit and the flow after gas turbine has strong swirl flow and turbulence. The inlet flow condition of HRSG should be included the exit flow characteristics of gas turbine. The present numerical analysis adopted the flow analysis result of gas turbine exit flow as a inlet flow condition of HRSG analysis. Because the flow characteristics in the inlet duct of the tube bank is strongly related to the performance of a HRSG, it is most important for the optimal design of HGSG to understanding the flow phenomena in the inlet duct of HRSG. From the present study, the position of breakpoint in the inlet expansion duct should be lower than the reference breakpoint position for the optimal flow uniformity before the tube bank.

• Proceedings of the Korean Society for Technology of Plasticity Conference
• /
• 2007.05a
• /
• pp.223-225
• /
• 2007

Online models predicting roll force and forward slip of roughing mill was developed using nondimensional parameters. Using the effective inlet thickness, roll force model take into account the effect of inlet dog-bone shape of slab which take places after width reduction through edger rolling in roughing mill. The prediction accuracy of the proposed model is examined through comparison with measurements.

• 제어로봇시스템학회:학술대회논문집
• /
• 2004.08a
• /
• pp.68-71
• /
• 2004

Recently, a great deal of research and development of a fuel cell have been carried out to solve problems on the drain of fossil fuel, air pollution and global warning. In order to improve the efficiency of a fuel cell, it is necessary to clarify the flow in separator. In this study, distributions of velocity flow rate and pressure, and streamlines are examined in detail from numerical analysis with CFD code. In the experiment the distribution of flow rate is measured and flow in the each grooves of the separator is visualized by dye method changing Reynolds number. Furthermore, effects of size of the inlet and outlet manifolds and shape of ribs near the inlet outlet on the distributions of flow and pressure are examined.

• Tribology and Lubricants
• /
• v.14 no.3
• /
• pp.87-93
• /
• 1998

Crank pin bearing in two-stroke marine diesel engine is operated under quite severe conditions since the elements are big and heavy and the sliding speed is very slow. Therefore it is very difficult to form oil film. In this paper, two types of bearings with different groove shape are compared. One has circumferential oil groove at lower position and the other has lengthwise oil groove at upper position. Bearing clearance, oil inlet pressure and length to diameter ratio are selected as design parameters. Locus of journal center and minimum oil film thickness are investigated to compare two cases.

• Journal of Advanced Marine Engineering and Technology
• /
• v.33 no.5
• /
• pp.653-661
• /
• 2009

In order to reduce the noise and oscillation, it is consider a matter in all aspects about the noise stem from accumulator and the characteristic of transmission, Transformation of outside shape has change of noise occurrence at transmission process. Therefore, performed sound numerical analysis and conducted an experiment to examine the birthplace of accumulator's external shape change. In a sound numerical analysis, we can fond out transmission loss between inlet and outlet's sound pressure. In an experiment, we can make out transmission loss by sound wave separation theory through drawing sound pressure inlet and outlet.