• Advanced Composite Materials
• /
• 제16권3호
• /
• pp.207-221
• /
• 2007

The filling process of resin injection/compression molding (I/CM) can be divided into injection and compression phases. During the resin injection the mold is kept only partially closed and thus a gap is present between the reinforcements and the upper mold. The gap results in preferential flow path. After the gap is filled with the resin, the compression action initiates and forces the resin to penetrate into the fiber preform. In the present study, the resin flow in the gap is simplified by using the Stokes approximation, while Darcy's law is used to calculate the flow field in the fiber mats. Results show that most of the injected resins enter into the gap during the injection phase. The resin injection time is extremely short so the duration of the filling process is determined by the final closing action of the mold cavity. Compared with resin transfer molding (RTM), I/CM process can reduce the mold filling time or injection pressure significantly.

• 한국정밀공학회지
• /
• 제25권5호
• /
• pp.43-51
• /
• 2008

Generally a plastic injection molding is a manufacturing process used to produce the various parts of complicated shape at low cost. The objective of this study is to implement a new plastic injection molding process with inserted Aluminum sheet, which is highly durable, light and luminous. Moldflow analysis and simulation of plastic injection molding process with inserted Aluminum sheet were carried out in order to predict optimal molding operation conditions. The experimental results in the Al-inserted plastic injection molding process were compared with the simulation results by Moldflow. Durability and reliability test results for trial products were satisfied to adopt the Al-inserted plastic injection molding process developed as manufacturing of automobile interior parts.

• 한국자동차공학회논문집
• /
• 제17권2호
• /
• pp.67-74
• /
• 2009

Injection molding have been used for manufacturing various fields of automotive interior trims for years. The demands on the injection molding technique are grown with the further development of the automobile technique and the design presentations for cost reduction and environment-friendly. This paper shows that multi-component injection conditions are different from general injection, also shows how to optimize part design and mold design and how to manufacturing through the efficient use of multi-component injection in development process using core back system. To fulfill this purpose, all influential process parameters related to the quality of automobile parts were analyzed in terms of the correlation between them. Base on that, a innovative process will be developed by injection engineers to implement it in practice.

• 한국정밀공학회:학술대회논문집
• /
• 한국정밀공학회 1997년도 추계학술대회 논문집
• /
• pp.833-836
• /
• 1997

Magnesium alloys are one of light weight material. Strength and stiffness of Magnesium alloys are enough to use for commercial product. Demand for strong, lightweight parts several computer and electronics have driven much of Magnesium injection molding's growth so far. And it is eighth most abundant resource on earth. In electronic device, electromagnetic interface and electrostatic discharge can affect performance. Magnesium injection molding is similar to normal plastic injection molding process. But some process condition is different. Especially injection speed and process temperature are so differs from other injection molding system. It just start for make something. But Magnesium injection molding is one of best alternate process for producing metal alloy part.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2007년도 추계학술대회 논문집
• /
• pp.302-305
• /
• 2007

In recent years, many researches on new storage media with high capacity and information are developing. For manufacture of optical storage with high capacity, the injection molding process is generally used. In order to increase the filling ratio of the injection molding structure, the injection molding process required for high injection pressure, packing pressure and temperature control of the mold. However, conventional injection molding process is difficult to increase the filling ratio using injection master with the range of several nanometers and high aspect ratio. In order to improve and increase filling ratio of nano-structure with high aspect ratio, the active temperature control of injection mold was used. Experimental conditions were used injection pressure, time and temperature. Consequently, by using the peltier device into injection mold, we carried out the efficient and active temperature control of mold at low cost.

• 대한기계학회:학술대회논문집
• /
• 대한기계학회 2001년도 춘계학술대회논문집C
• /
• pp.621-626
• /
• 2001

Microcellular foaming process was developed at MIT in 1980's to save a quantity of raw materials and improve mechanical properties. There are many process variables in appling microcellular foaming process to the conventional injection molding process. Of all process variables, part dimension control and shrinkage are the most influential on the post molded dimension. The post molding dimensional change of thermoplastic resins is important to tool designers for predicting the specific difference of molded part vs. actual mold cavity. Generally, articles injection molded are smaller in size than the cavity; hence, the term shrinkage factor is used to define the allowance a designer specifies. It is important to consider the factors that influence molded part dimension. According to ASTM Designation: D 955, shrinkage from mold dimensions of molded plastics was measured. In injection molding, the difference between the dimensions of the mold and of the molded article produced therein from a given material may vary according to the design and operation of the mold. In this paper, shrinkage data of molded plastic parts was obtained. It can be an important information for designing optimum mold system in a microcellular foaming injection molding process.

• 한국공작기계학회논문집
• /
• 제11권4호
• /
• pp.44-53
• /
• 2002

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for the filling and packing phases. Molding troubles like flow mark weld line, sink ma가 short shot and warpage car be caused by these injection molding process factors. Among them the short shot was caused by the fact that the packing pressure could not reach properly to the filling end part in the packing phase and hence the flow rate could not be supplied to the full. In addition as the flow rate for the volumetric shrinkage during the f개zen phase could not be supplied Properly by the packing pressure, the short shot appeared. Here, the volumetric shrinkage reduced with increasing the packing pressure and also the warpage of molded part increased with increasing the packing Pressure.

• 한국CDE학회논문집
• /
• 제11권6호
• /
• pp.440-446
• /
• 2006

This study relates to the effect of forming time of injection path on the total process. The whole process can be divided into build process of forming path of injection and after treatment process. The total time required for the whole process could be reduced by reducing the forming time of injection path using SLC file to correct the problems of STL file that is the basic file format for high speed molding devices. First of all, I verify the forming time of injection path according to the conditions of STL file during the formation of injection path. And I verify problems using STL file during formation of injection path. And then I tried to solve problems of STL file by comparing between the formation time of injection path and the existing method using SLC files.

• Advances in materials Research
• /
• 제3권2호
• /
• pp.91-103
• /
• 2014

A study that demonstrates how to investigate the molded part quality and the consistency of injection process based on the rheological concept is proposed. It is important for plastic material whose melt viscosity is variable with respect to the processing condition. The formulations to couple the melt viscosity with injection pressure and fill time are derived first. Taking calculations of the measured pressure and the time by using these formulations, the melt viscosity in injection process can be determined on machine. As the relation between the injection speed and the melt viscosity is constructed, the influences of the setting parameter of injection machine on the molded part quality can be investigated through evaluating the state of the melt viscosity. In addition, a pressure sensor bushing (PSB) designed with a quick installation feature is also provided and validated. The results show that a higher injection speed improves the tensile strength of the molded part but also the consistency of the molded part quality. This work provides an alternative to evaluate the molding quality scientifically.

• 한국공작기계학회논문집
• /
• 제16권6호
• /
• pp.21-28
• /
• 2007

Injection molding process factors such as molding temperature, injection pressure, flow rate and flow velocity, must be controlled properly in filling and packing phases in the injection molding process. In this study, effects of these factors on the injection molding were investigated through the flow analysis for birefringence and refractive index for pickup lens. This paper presents the birefringence and refractive index reduced with increasing the holding pressure and also the holding pressure time. And there are interaction with birefringence and fill time in the injection process. The optimal conditions through DOE are validated by using injection molding analysis.