• 한국연소학회지
• /
• 제4권1호
• /
• pp.117-129
• /
• 1999

A method for the mixing augmentation of the transverse injection of fuel in a Scramjet combustor is suggested. Based on the fact that the main factor controlling the mixing characteristics in transverse injection is the effective back-pressure (the pressure around the injection hole) it is tried to make a flow expansion near the injection port in order to reduce effective back-pressure. A three dimensional Navier-Stokes code adopting the upwind method of Roe#s flux difference splitting scheme is used. The k-w SST turbulence model turbulence model is used to calculate the turbulent viscosity. It is shown that the reducing of the effective back-pressure make it possible to increase the penetration distance and to increase the mixing rate without excessive losses of stagnation pressure. Also, it is shown that the streamwise vorticity generated by baroclinic torque has great influences on the mixing process.

• 대한기계학회논문집
• /
• 제12권2호
• /
• pp.359-372
• /
• 1988

본 연구에서는 두 노즐간의 거리와 분사압력을 변화시켜 하류로 전개되는 이중분무의 분무형태를 살펴보았다.

• 한국분무공학회지
• /
• 제23권1호
• /
• pp.22-29
• /
• 2018

The purpose of this study is to investigate the macroscopic spray characteristics and spray pattern of a gasoline direct injection (GDI) injector according to the increase of injection pressure. The macroscopic spray characteristics, such as a spray tip penetration and spray angle, were measured and analyzed from the frozen spray images, which are obtained from the spray visualization system including the high-speed camera, light-source, long-distance microscope (LDM). The spray pattern was analyzed through the deviation of the center of the spray plum and images were acquired using Nd: YAG Laser and ICCD(Intensified charge coupled device) camera. From the experiment and analysis, it revealed that the injection pressure have a significant influence on the spray tip penetration and spray pattern. However, the injection pressure have little influence on the spray angle. The increase of injection pressure induced the reduction of a closing delay. In addition, the deviation of spray center increase with the increase of injection pressure and the distance from a nozzle tip.

• 한국산업융합학회 논문집
• /
• 제26권5호
• /
• pp.907-913
• /
• 2023

Currently, the sprinkler method is widely used as an initial suppression method in existing firefighting systems. However, this method can cause significant damage to both equipment and facilities in the hydration area. To minimize this damage, fire extinguishing monitors are being developed that can spray fire extinguishing water directly at the point of fire. These monitors are installed on the top floor of the ship, such as the Living Quarter and Ventilation System. While conventional fire extinguishing monitors focus on lightweight research with a short spray port and require a spray distance of about 40 to 45m, recent developments necessitate a longer spray port, similar to a water cannon, requiring a spray distance of about 70 to 75m. This study aims to predict the injection distance of both the existing ship-installed fire extinguisher and the long spray port fire extinguisher through hydrodynamic computer analysis, and to determine whether the injection distance has increased.

• 한국자동차공학회논문집
• /
• 제6권5호
• /
• pp.182-190
• /
• 1998

Behaviour of ultra-high pressure diesel spray in a constant-volume pressure chamber was studied with injection pressure ranging from 20 to 160㎫. Sprays were observed by the right angle scattering method. As a result, the spray tip penetration is first proportional to a time, and after that, it is proportional to 0.52 of the time during at the time of injection pressure and back pressure increase. An empirical correlation was made for the parameters of injection pressure, air-fuel density ratio, spray tip distance, spray angle, jet angle of spray and max. spray width.

• 한국기계가공학회지
• /
• 제20권9호
• /
• pp.76-83
• /
• 2021

This study examines the characteristics of spraying conditions based on the change in standoff distance during fine particle spraying while measuring the surface roughness, maximum depth, and maximum width of the sprayed surface. The processing shape of the sprayed surface is analyzed to understand the effects of injection pressure, nozzle diameter, standoff distance, processing shape, processing cycle, processing speed, and injection particles, which are the main factors of fine particle injection processing. Based on the derived characteristics, we attempt to determine the interrelationships of these major factors. The standoff distance is set as a variable factor and a spray machining experiment using a hexagonal shape (from among polygons) instead of square and circular shapes is conducted. Results reveal that research on the characteristics of spraying conditions could be expanded based on changes in the shapes of workpieces.

• International Journal of Automotive Technology
• /
• 제7권5호
• /
• pp.585-593
• /
• 2006

The effect of the shape of the side wall on vaporization and fuel mixture were investigated for the impinging spray of a direct injection(DI) gasoline engine under a variety of conditions using the LIEF technique. The characteristics of the impinging spray were investigated under various configurations of piston cavities. To simulate the effect of piston cavity configurations and injection timing in an actual DI gasoline engine, the parameters were horizontal distance from the spray axis to side wall and vertical distance from nozzle tip to impingement plate. Prior to investigating the side wall effect, experiments on free and impinging sprays for flat plates were conducted and these results were compared with those of the side wall impinging spray. For each condition, the impingement plate was located at three different vertical distances(Z=46.7, 58.4, and 70 mm) below the injector tip and the rectangular side wall was installed at three different radial distances(R=15, 20, and 25 mm) from the spray axis. Radial propagation velocity from spray axis along impinging plate became higher with increasing ambient temperature. When the ambient pressure was increased, propagation speed reduced. High ambient pressures tended to prevent the impinging spray from the propagating radially and kept the fuel concentration higher near the spray axis. Regardless of ambient pressure and temperature fully developed vortices were generated near the side wall with nearly identical distributions, however there were discrepancies in the early development process. A relationship between the impingement distance(Z) and the distance from the side wall to the spray axis(R) was demonstrated in this study when R=20 and 25 mm and Z=46.7 and 58.4 mm. Fuel recirculation was achieved by adequate side wall distance. Fuel mixture stratification, an adequate piston cavity with a shorter impingement distance from the injector tip to the piston head should be required in the central direct injection system.

• 항공우주시스템공학회지
• /
• 제12권4호
• /
• pp.81-89
• /
• 2018

본 연구에서는 초음속 유동장 내 연료 분사시 연소기의 공간적인 제한 조건을 고려하여 복수의 분사기간 배치 간격을 변화시키고 그에 따른 유동 구조, 연료의 침투 거리 및 연료-공기의 혼합 특성을 비교 분석하였다. 이를 위하여 널리 알려진 단일 분사구를 이용한 실험 조건을 모사하여 적용된 수치 모델을 검토하였으며, 동일한 분사 조건을 갖는 복수의 분사기를 이용하여 비반응 유동 해석을 수행하였다. 해석 결과를 바탕으로 분사구 간 거리에 따라 전압력 손실, 침투 거리, 및 혼합 성능 등을 정량적으로 비교하였다. 해석 결과 분사구 간 배치 거리가 매우 짧은 경우 분사 연료가 서로 융합되면서 유동장이 2차원 특성을 나타내었고 전반적으로 낮은 혼합 효율 특성과 높은 전압력 손실을 발생하였다. 분사구 간 거리가 멀어짐에 따라 분사 가스간의 상호작용이 감소하면서 혼합 효율이 증가하고 전압력 손실이 낮아지는 것이 관찰되었다.

• 한국지반환경공학회 논문집
• /
• 제3권3호
• /
• pp.27-36
• /
• 2002

일반적으로 우레탄 주입은 장기 강도와 환경친화적인 측면에서 우수성을 보이고 있다. 하지만 우레탄 공법은 짧은 Rise-time을 가지고 있으므로 주입구에서부터 아주 짧은 침투 반경을 보인다. 그러므로 깊은 지점의 지반개량을 위해서는 우레탄 공법이 사용 될 수 없다. 시멘트와 같은 다른 주입재는 급속한 경화가 필요한 현장에서는 그 대안이 되지 못하였다. 따라서 본 연구를 통해서 우레탄 공법의 단점을 TAS 공법을 통하여 보강하고자 한다. 현장실험을 실시한 결과 TAS 공법은 기존의 우레탄공법을 통하여 침투 주입 할 수 있는 거리보다 훨씬 더 먼 거리의, 10m 주입이 확인되었다. 또한 TAS 공법은 시멘트 그라우팅에 비해 상대적으로 짧은 Rise-time을 보이므로 주입 후 즉각적인 지반보강효과를 확인 할 수 있다. 짧은 Rise-time과 긴 침투주입구간 등의 장점으로 TAS 공법은 터널등에서 그 적용성이 기대된다.

• 한국소성가공학회:학술대회논문집
• /
• 한국소성가공학회 2009년도 춘계학술대회 논문집
• /
• pp.361-364
• /
• 2009

The cooling system optimization for injection molds was studied with a response surface method in the previous research. It took so much time to find an optimum solution for a large product due to an extensive amount of calculation time for the CAE analysis. In order to use the optimization technique in the actual design process, the calculation time should be much reduced. In this study, we tried to reduce the number of design variables with the concept of the close relationship between the depth and the distance of cooling channels. The optimum ratio of the distance to the depth of cooling channels for a 2-dimensional problem was 2.0 so that the optimum ratio was again sought out for 4 industrial products. The major cooling effect of the injection molds for large products rely on baffle tubes. The optimum ratio of the distance to the depth for baffle tubes was 2.0 for the large products. The result enables us to reduce the number of the design variables by half in the cooling system optimization problem.