• Journal of the Korean Society of Combustion
• /
• v.8 no.3
• /
• pp.31-37
• /
• 2003

The objective of this work is to investigate the effect of swirl, injection pressure and pilot injection on D.I.Diesel combustion by using a transparent engine system. The test engine is equipped with common rail injection system to obtain high pressure and to control injection timing and duration. In this study, the combustion analysis and steady flow test were conducted to estimate the heat release rate from in-cylinder pressure and pilot injection was investigated by using LII technique. As the results, high injection pressure was found to shorten ignition delay as well as enhance peak pressure and heat release rate was greatly affected by injection timing and pilot injection. In addition, the results showed that the period of soot formation corresponded to the diffusion flame.

• Journal of ILASS-Korea
• /
• v.23 no.2
• /
• pp.96-101
• /
• 2018

The purpose of this study is to investigate the effect of water injection on combustion characteristics of gasoline direct injection (GDI) engine with turbo-charger under low-load operating condition. The test engine used in this study has four-cylinder and 10.2 of compression ratio. In order to study the effect of water injection ratio on combustion characteristics, the water was injected into the intake port from 10% to 50%, based on fuel injection quantity. From the experiment, it revealed that the water injection induced the improvement of fuel economy because of the advance of spark-timing by the reduction of in-cylinder temperature. In addition, the water injection caused the prolong of extension of the ignition delay and slight increase of burn duration.

• 한국정보디스플레이학회:학술대회논문집
• /
• 2007.08a
• /
• pp.165-167
• /
• 2007

The performance of polymer light emitting diode can be improved significantly by interfacial engineering on anode and/or cathode through adjusting the charge injection barriers for holes and electrons. Studies involve CFx and SAM modifications on ITO, thickness and delay time to baking of PEDOT:PSS, and electron injection/hole blocking layer.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.12 no.2
• /
• pp.308-318
• /
• 1988

The liquid disintegration and characteristics of atomization through the swirl nozzle is affected by injection pressure and injection time when the liquid is injected intermittently. These transient phenomena are investigated by electronic controlled-fuel injection nozzle. The effect of injection conditions on disintegration of liquid injected through nozzle is observed photographically by using delay circuit. Droplet size of the element of the sample is measured by the liquid immersion sampling technique. SMD of droplets is varied with time and is decreased as the injection pressure increases. As the injection pressure increases, the maximum diameter of droplet and diameter of droplet which has the maximum droplet number decrease. Spray angle is not affected on injection pressure and change of spray angle with time is associated with needle movement.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.5 no.1
• /
• pp.9-14
• /
• 1997

The pump-pipe-injector system is that most commonly used type of injection equipment for diesel engines. In this study, a new electromagnetic fuel injection system was designed and carried out the experiment of single cylinder direct injection(DI) diesel engine. This system do not need the cam shaft for fuel injection. The effects of the injection timing on the combustion process and emission were investigated. The results are that 1) atomization was improved, 2) combustion pressure was increased and ignition delay became shorter than before, 3) Low smoke level guarantee with more advanced injection timing without abnormal combustion but NOX concentration was increased as the injection time advanced.

• Transactions of the Korean Society of Automotive Engineers
• /
• v.11 no.5
• /
• pp.15-21
• /
• 2003

The liquid phase LPG injection engine is a new technology to make good use of LPG as a clean energy. However, it is difficult to precisely control air/fuel ratio in the system because of variation of fuel composition, change of temperature and flash boiling injection mechanism. This study newly suggests an injector control logic for liquid phase LPG injection systems. This logic compensates a number of effects such as variations of density, stoichiometric air/fuel ratio, injection delay time, injection pressure, release pressure which is formed by flash boiling of fuel at nozzle exit. This logic can precisely control air/fuel ratio with only two parameters of intake air flow rate and injection pressure without considering fuel composition, fuel temperature.

• Journal of Mechanical Science and Technology
• /
• v.20 no.9
• /
• pp.1436-1448
• /
• 2006

This paper describes the effects of injection rate shaping on the combustion, fuel consumption and emission of $NO_x$ and soot of a medium duty diesel engine. The focus is on the influence of four different injection rate shapes, square type 1, square type 2, boot and ramp, with a variation of maximum injection pressure and start of injection (SOI). The experiments were carried out on a 1 liter single cylinder research diesel engine equipped with an amplifier-piston common rail injection system, allowing the adjustment of the injection pressure during the injection event and thus injection rate as desired. Two strategies to maintain the injected fuel mass constant were followed. One where rate shaping is applied at constant injection duration with different peak injection pressure and one strategy where rate shaping is applied at a constant peak injection pressure, but with variable injection duration. Injection rate shaping was found to have a large effect on the premixed and diffusion combustion, a significant influence on $NO_x$ emissions and depending on the followed strategy, moderate or no influence on soot emission. Only small effects on indicated fuel consumption were found.

• Journal of Korean Foot and Ankle Society
• /
• v.21 no.4
• /
• pp.151-155
• /
• 2017

Purpose: Reducing tenderness or pain on the ankle joint and improving the range of motion are thought to be possible using hyaluronate-based anti-adhesive agents. On the other hand, there are more aspects to be studied regarding the incidence of complications, such as resting pain, tenderness, and stiffness, after surgery. Therefore, the aim of this study was to prove the effectiveness of the agents after ankle fracture surgery. Materials and Methods: Patients, who underwent open reduction and internal fixation surgery due to ankle joint fractures from June 2015 to May 2016, were studied prospectively. Thirty patients of them received a $Guardix^{(R)}$ injection during their surgeries and were included in the injection group. The other 30 patients were included in the control group. Postoperatively, tenderness on the scar, a delay in wound healing, and the active range of motion were evaluated at 2, 6, and 12 weeks after surgery. Results: A significant difference in tenderness on the scar was observed 2 weeks after surgery. On the other hand, there was no significant difference at 6 and 12 weeks after the surgery. The agent-using group showed a 6.7% delay in wound healing and a 93.3% nondelaying. In the non-using group, the delay was 63.3%, while non-delay was 36.7% (p<0.001). The group that underwent $Guardix^{(R)}$ usage showed an effective result in the visual analogue scale, which was statistically significant (p<0.001). The result at 6 and 12 weeks after surgery showed a significant difference. Conclusion: Improvement was observed in the patients who underwent a $Guardix^{(R)}$ injection, regarding the range of motion, visual analog scale, and healing of the wound postoperatively.

• Transactions of the Korean Society of Mechanical Engineers
• /
• v.10 no.3
• /
• pp.367-375
• /
• 1986

On the hypothesis that the unstable intermediates yield by the pre-reaction of auxiliary fuel become an initiator or an explosive center which promotes the chain reaction of main fuel, various organic compounds below $C_{10}$ are injected as an auxiliary fuel prior to main injection. In the previous papers, the effects of the auxiliary fuel additions on the ignition delay period, the stability of flame, the NO concentrations in their exhaust gases have been investigated. In the present paper, to confirm where the most suitable location of lean pre-mixture for the combustion of main fuel is, and how the lean pre-mixture is contacted with main fuel, the effects of the injection timing of auxiliary fuel and the turbulence on combustion processes are investigated. Moreover, from the schlieren and color photographs of flame in the combution field, it could be found that the ignition nuclei are formed in a wider region of main spray, and that these ignition nuclei promote the development of flame, which results in the reduction of flaming duration.

• Journal of Fisheries and Marine Sciences Education
• /
• v.9 no.1
• /
• pp.83-97
• /
• 1997

Diesel engine is widely used for ship and industry source of power because of its high thermal efficiency and reliability and durability. However it lead to air pollution due to exhaust gas, and it is important to develop diesel engine of lower air-pollution to decrease the hazardous exhaust gas emissions. As one of the ways, the study for practically using the high pressure of fuel injection and variable injection timing system is being processing. The high pressure injection, which is said to be an effective means for reducing both NOx and particulate emissions, and great improvements in combustion characteristics have been reported by many researchers. In this study, electronic-hydraulic fuel injection system and hydraulic fuel injector system have been applied to the D.I. test engine for high pressure injection and variable injection timing. The injection pressure and injection rate depending upon accumulator pressure were measured with strain gage and Bosch injection rate measuring system before fitting the system into test engine, and analyzed the characteristics of the injection system. The combustion characteristics with this injection system has been analyzed with data concerning heat release rate, pressure rising rate, ignition point, ignition delay and maximum pressure value.