• Journal of the Korea Academia-Industrial cooperation Society
• /
• v.11 no.4
• /
• pp.1361-1366
• /
• 2010

This research aims to develop polymer composites which can be used for PEMFC separators by injection molding process. Considering the moldability and stiffness, we used PPS(Poly(phenylene sulfide)) and PP(Polypropylene) as base resin. In order to improve electrical conductivity and physical properties, we chose glass fiber, carbon fiber, carbon black, and both expanded graphite and synthetic graphite. The 3 type composites are prepared for injection molding of PEMFC separators. and CAE(Computer Aided Engineering) analysis was conducted to optimize injection processing parameters(injection pressure, heat time, mold temperature etc.). We did successfully fabricate the separators by injection molding, and measure the electrical conductivity of the samples by using four point probe device. Conclusively, PP/SG/CB composite showed better both electrical conductivity and moldability than the others.

• Journal of Environmental Health Sciences
• /
• v.44 no.6
• /
• pp.599-607
• /
• 2018

Objectives: Carbon dioxide ($CO_2$) may be one of the biggest causes of climate change. The purposes of this study were to reduce greenhouse gases and to increase strawberry production by developing the supply devices in livestock facilities using the membrane technology Methods: Carbon dioxide was collected from beside to livestock facilities. The injection of $CO_2$ was stopped when it reached 1,000 ppm in the facility house. Case group with injection of $CO_2$ was compared to control group with normal environment. The experiments were conducted for 8 days from December 11, 2017. Results: Total strawberry production was found to be 1,317 kg in the case group and 1,176 kg in the control group. The correlation between $CO_2$ and crop yields has led to some statistical evidence that carbon dioxide helps to grow (${\beta}=0.832$, p<0.05). Conclusions: This study identified the potential for efforts to reduce the $CO_2$ in farming households. Increased concentrations of $CO_2$ have shown that strawberries have a better growth condition. In addition, it can be explained that the plants need wide leaves to quickly absorb much $CO_2$.

• Steel and Composite Structures
• /
• v.38 no.2
• /
• pp.177-187
• /
• 2021

The effect of nanoparticle volume fraction on the elastic properties of a polymer-based nanocomposite was experimentally investigated and the obtained results were compared with various existing theoretical models. The nanocomposite was consisted of high density polyethylene (HDPE) as polymeric matrix and 0, 0.5, 1 and 1.5 wt.% multi walled carbon nanotubes (MWCNTs) prepared using twin screw extruder and injection molding technique. Nanocomposite samples were molded in injection apparatus according to ASTM-D638 standard. Therefore, in addition to morphological investigations of the samples, tensile tests at ambient temperature were performed on each sample and stress-strain plots, elastic moduli, Poisson's ratios, and strain energies of volume units were extracted from primary strain test results. Tensile test results demonstrated that 1 wt.% nanoparticles presented the best reinforcement behavior in HDPE-MWCNT nanocomposites. Due to the agglomeration of nanoparticles at above 1 wt.%, Young's modulus, yielding stress, fracture stress, and fracture energy were decreased and Poisson's ratio and failure strain were increased.

• Journal of the Korean GEO-environmental Society
• /
• v.24 no.6
• /
• pp.5-11
• /
• 2023

The engineering industry heavily relies on fossil fuels such as coal and petroleum to generate energy through combustion. However, this process emits carbon dioxide into the atmosphere, leading to global warming. To mitigate this issue, researchers have explored various methods to reduce carbon dioxide emissions, one of which is carbon dioxide underground storage technology. This innovative technology involves capturing carbon dioxide from industrial plants and injecting it into the saturated ground layer beneath the earth's surface, storing it securely underground. Despite its potential benefits, carbon dioxide underground storage efficiency needs improvement to optimize storage in a limited space. To address this challenge, our research team has focused on improving storage efficiency by utilizing surfactants. Furthermore, we evaluated how different carbon dioxide states, including gaseous, liquid, and supercritical, impact storage efficiency based on their respective pressures and temperatures within the underground reservoir. Our findings indicate that using surfactants and optimizing the injection rate can effectively enhance storage efficiency across all carbon dioxide states. This research will pave the way for more efficient carbon dioxide underground storage, contributing to mitigating the environmental impact of fossil fuels on the planet.

• Journal of Advanced Marine Engineering and Technology
• /
• v.39 no.9
• /
• pp.911-917
• /
• 2015

The objective of this work focuses on the analysis of injection rate and macroscopic spray behavior characteristics with injection pressures as well as combustion and exhaust emission characteristics with injection timing and injection pressure by using a common rail single-cylinder diesel engine. The injection rate was measured by applying the Bosch method, and macroscopic spray behavior characteristics were analyzed with a constant-volume vessel and a high-speed camera. In addition, combustion and emission characteristics were analyzed in a common-rail single-cylinder diesel engine with precise control of fuel injection timing and pressure. For injection pressures of 30MPa and 50MPa, the injection rate was higher at 50 MPa, and the spray development (penetration) was also higher in the same elapsed time. The peak in-cylinder pressure and rate of heat release showed a tendency to decline as injection timing was delayed, and the peak in-cylinder pressure and rate of heat release were slightly higher for higher injection pressures. Higher injection pressures also reduced the mean effective pressure, while the indicated mean effective pressure and torque increased as injection timing was delayed to TDC. Nitrogen oxides had a peak level at injection timings of $BTDC20^{\circ}$(30MPa) and $BTDC15^{\circ}$(50MPa); carbon monoxide emissions were reduced by delaying injection timing from $BTDC30^{\circ}$.

• Transactions of the Korean Society of Mechanical Engineers A
• /
• v.25 no.4
• /
• pp.564-573
• /
• 2001

The mechanical properties of short carbon/glass fiber reinforced polypropylene are experimentally measured as functions of fiber content and nozzle diameter. Also, these properties are compared with the survival rate of reinforced fibers and fiber volume fraction using image analysis after pyrolytic decomposition. The survival rate of fiber aspect ratio as well as fiber volume fraction is influenced by injection processing condition, the used materials and mold conditions such as diameter of nozzle, etc. In this study, the survival rate of fiber aspect ratio is investigated by nozzle size variations in injection/mold sides. It is found that the survival rate of glass fiber is higher that the survival rate of glass fiber is higher than that of carbon fiber. Both tensile modulus and strength of short-fiber reinforced polypropylene are improved s the fiber volume fraction and nozzle diameter are increased.

• Journal of Powder Materials
• /
• v.21 no.6
• /
• pp.407-414
• /
• 2014

The powder injection molding process having advantages in manufacturing three-dimensional precision parts essentially requires a debinding process before sintering to remove the binders used for preparing feedstock. In this study, powder injection molding of translucent alumina was performed, and carbon dioxide ($CO_2$) is used as a supercritical fluid that makes it possible to remove a large amount of binder, which is paraffin wax. The relationship between the optical property of translucent alumina and the debinding condition (temperature and pressure) of supercritical $CO_2$ was investigated. As temperature and pressure increased, extraction rate of the binder showed rising tendency and average grain size after sintering process was relatively fine. On the other hand, optical transmittance was reduced. As a result, the debinding condition at $50^{\circ}C$ and 20 MPa that represents the lowest extraction rate, $8.19{\times}10^{-3}m^2/sec$, corresponds to the largest grain size of $14.7{\mu}m$ and the highest optical transmittance of 45.2%.

• Journal of the Korean Society of Industry Convergence
• /
• v.4 no.3
• /
• pp.267-273
• /
• 2001

In this study, the survival rate of fiber is investigated by nozzle size difference in injection/mold sides. The survival rate of fiber is influenced about the nozzle size differ. Also, The mechanical properties of short carbon glass fiber reinforced polypropylene are experimentally measured as functions of fiber volume fraction and nozzle size difference. These mechanical properties are compared with the survival rate of fiber and fiber volume fraction using image analysis after pyrolytic decomposition. The survival rate of fiber as well as fiber volume fraction is influenced by injection processing condition, the used materials, mold conditions and nozzle sides difference, etc, In particular, the survival rate of fiber is great influenced when injection/mold nozzle sides are different more than that of the same. Consequently, the mechanical properties of short carbon/glass fiber reinforced polypropylene arc improved as the nozzle sides are the same in injection mold sides.

• Journal of Energy Engineering
• /
• v.13 no.4
• /
• pp.301-310
• /
• 2004

Carbon dioxide ocean disposal is one of the promising options to reduce carbon dioxide concentration in the atmosphere. So, in the present study, calculations of the solubility, the surface concentration and the dissolution behavior of carbon dioxide when liquid carbon dioxide is released at 1,000m and 1,500m in depth are performed. The results show that liquid carbon dioxide changes to carbon dioxide bubbles around 500m in depth, and the hydrate acts as a resistant layer for the dissolution of liquid carbon dioxide. Also. the injection of liquid carbon dioxide from a moving ship is more effective than that from a fixed pipeline.

• Korean Journal of Veterinary Research
• /
• v.18 no.2
• /
• pp.87-95
• /
• 1978

Election microscopic investigation were conducted on the mature mouse (B.W. about 25g) liver which was treated with Ginseng water extract during three, six and nine days respectivelly after carbon tetracholride injection into abdominal cavity. The results obtained were as follows: The liver cells of control group treated with carbon tetrachloride alone were restored slowly. The liver cells of experimental group treated with Ginseng water extract after carbon tetrachloride injection, however, were shown the appearance of well-developed ${\gamma}-ER$ and Golgi complex, marked aggregation of glycogen particles, and a number of large lipid droplets which are attached markedly with glycogen particles as compared to the control group. As these findings, it could be suggested that Ginseng gives an activation to restore the damaged liver cells.