• Transactions of the Korean Society of Mechanical Engineers B
• /
• v.37 no.7
• /
• pp.655-663
• /
• 2013

Several studies of film cooling were accomplished with a secondary flow channel parallel to the main flow. In real turbine blades, however, the direction of the secondary flow channel is generally normal to the main flow. Thus, this study performs a numerical analysis to investigate the effects of the direction of secondary flow on the effectiveness of double-jet film cooling. The blowing ratio is 1 and 2, and the lateral injection angle is $22.5^{\circ}$. The parallel channel case creates a well-developed anti-kidney vortex with a blowing ratio of 1, and the laterally averaged film cooling effectiveness of the parallel channel is enhanced compared to the normal channel. The normal channel shows higher performance with a blowing ratio of 2. Both cases show high film cooling effectiveness. These phenomena can be attributed to a high blowing ratio and flow rate rather than an anti-kidney vortex.

• Journal of Mechanical Science and Technology
• /
• v.14 no.10
• /
• pp.1131-1142
• /
• 2000

In an effort to illustrate the global variation of SMD (Sauter mean diameter, or $D_{32}$) and AMD (Arithmetic mean diameter, or $D_{10}$) at five axial downstream locations (i. e., at Z=30, 50, 80, 120, and 170 mm) under the different experimental conditions, the radial coordinate is normalized by the spray half-width. Experimental data to analyze the atomization characteristics concerning with an internal mixing type have been obtained using a PDPA(Phase Doppler Particle Analyzer). The air injection pressure was varied from 40 kPa to 120 kPa. In this study, counterflowing internal mixing nozzles manufactured at an angle of $15^{\circ}$with axi-symmetric tangential-drilled four holes have been considered. By comparing the results, it is clearly possible to discern the effects of increasing air pressure, suggesting that the disintegration process is enhanced and finer spray droplets can be obtained under higher air assist. The variations in $D_{32}$ are attributed to the characteristic feature of internal mixing nozzle in which the droplets are preferentially ejected downward with strong axial momentum, and dispersed with the larger droplets which are detected in the spray centerline at the near stations and smaller ones are generated due to further subsequent breakup by higher shear stresses at farther axial locations. The poor atomization around the centre close to the nozzle exit is attributed to the fact that the relatively lower rates of spherical particles are detected and these drops are not subject to instantaneous breakup in spite of the strong axial momentum. However, substantial increases in SMD from the central part toward the edge of the spray as they go farther downstream are mainly due to the fact that the relative velocity of droplet is too low to cause any subsequent disintegration.

• Tunnel and Underground Space
• /
• v.23 no.6
• /
• pp.470-479
• /
• 2013

Hydraulic fracturing is used as a method for promoting the fluid flow in the rock and, in the energy field such as geothermal development and the development of sales gas, many studies has been actively conducted. In many cases, hydraulic fracturing is not performed in isotropic rock and especially in the case of sedimentary rocks, hydraulic fracturing is conducted in the transverse isotropic rock. The direction of the crack growth on hydraulic fracturing does not necessarily coincides with the direction of maximum principal stress in the transverse isotropic rock. Therefore, in this study, bonded particle model with hydro-mechanical coupling analysis was adopted for analyzing the characteristics of hydraulic fracturing in transverse isotropic rock. In addition, experiments of hydraulic fracturing were conducted in laboratory-scale to verify the validity of numerical analysis. In this study, the crack growth and crack patterns showed significant differences depending on the viscosity of injection fluid, the angle of bedding plane and the influence of anisotropy. In the case of transverse isotropic model, the shear crack growth due to hydraulic fracturing appeared prominently.

• Journal of the Korean Society of Manufacturing Technology Engineers
• /
• v.26 no.2
• /
• pp.158-165
• /
• 2017

This study investigated spraying factors applicable to stripper usage. Cyclodextrine, as environment-friendly material, was included in the stripper composition. An efficient spray technology was applied for the Photoresist strip. For industrial applications, stripping requires a temperature below $50^{\circ}C$, a strip time within 50 s, and chemically stable activation. Spraying factors were organized considering many conditions-orifice diameter, working pressure (inlet speed), spray distance, and spray angle. For commercial practicability, the flow rate was limited to 3 L/min. The nozzle parameters were nozzle orifice diameter of 1.8-2.2 mm, spray distance of 40-60 mm, and injection speed of 0.7-1.2 m/s. Through the thermal spray movement of the fluid, the thermal boundary layer for a chemical reaction just above the ITO-glass surface and momentum region for sufficient agitation (above 4 m/s) was achieved.

• Journal of the Korean Society for Aeronautical & Space Sciences
• /
• v.30 no.6
• /
• pp.1-6
• /
• 2002

Micro engine that includes Micro scale combustor is fabricated. Design target was focused on the observation of combustion driven actuation in MEMS scale. Combustor design parameters are somewhat less than the size recommended by feasibility test. The engine structure is fabricated by isotropic etching of the photosensitive glass wafers. Electrode is formed by electroplating of the Nickel. Photosensitive glass can be etched isotropically with almost vertical angle. Bonding and assembly of structured photosensitive glass wafer from the engine. Combustor size was determined to be 1mn scale. Piston in cylinder moves by fuel injection and reaction. In firing test, adequate engine operation including ignition, flame propagation and piston motion was observed. Present study warrants further application research on MEMS scale internal combustion power units.

• The Journal of Engineering Geology
• /
• v.11 no.3
• /
• pp.279-294
• /
• 2001

When constructing subsurface structures and drilling wells, the precise hydraulic parameters must be obtained for operating safety and for developing enough quantity of groundwater, respectively. In this study we conducted water injection test at different depths on six boreholes drilled in the granite of Mt. Geumjeong. Hydraulic conductivity was calculated using Moye and Hvorslev methods. The relation between hydraulic conductivity and fracture frequency data obtained from acoustic televiewer and core log was analyzed. From the result, though the correlation coefficient between the hydraulic conductivity and the fracture frequency from acoustic televiewer data is higher than that between the hydraulic conductivity and the fracture frequency from core log data on most of the test holes, the correlation coefficient between the hydraulic conductivity and the fracture frequency from the televiewer data is lower than 0.5. This suggests that the hydraulic conductivity of granite in the study area is influenced not only by the fracture frequency but also by various factors of fracture network such as fracture aperture and length, interconnectivity of fractures, fracture orientation and angle, filling material and so on.

• Journal of the Society of Naval Architects of Korea
• /
• v.30 no.1
• /
• pp.94-103
• /
• 1993

This study deals with an investigation on the tip vortex generated by an elliptic wing with section shapes of NACA 0020. The flow structure on the wing surface is investigated by using tufts test as well as observing the cavitation pattern. The surface pressure on a foil surface is measured to complement the visualized flow field. Results show that a strong spanwise pressure gradient is a definite contributor on the formation of tip vorex, and the fluids from both sides contribute to the evolutionary process of tip vortex. On the other hand, a series of experiments are conducted to investigate the detailed structure of tip-vortex at various angles of attack. The tip-vortex formation and development are observed by producing a cavitation, and then by a laser sheet technique in conduction with a dye injection method. The shape of tip-vortex and the distance between a vortex core and the trailing vortex sheet are found to vary with the angle of attack. Overall features of tip flow are evaluated to complement the vortex model based on inviscid theory.

• Journal of Veterinary Clinics
• /
• v.37 no.5
• /
• pp.261-269
• /
• 2020

The purpose of this study is to investigate the clinical effects of carboxymethyl chitosan (CMC) and adipose-derived mesenchymal stem cells (MSCs) on osteoarthritis (OA). Thirty New Zealand white rabbits were used as cranial cruciate ligament transection and partial meniscectomy models. The rabbits were divided into five groups (n = 6) according to the intra-articular injection materials: the control group with PBS, the HA group with hyaluronic acid, the CMC group with CMC, the MSC group with MSCs emerged in PBS, and the MSC+CMC group with CMC and MSCs. Knee thickness, extension angle, gross morphology, histopathology and immunohistochemistry were performed to evaluate the effects of CMC and MSCs on rabbit OA. On the morphologic and histologic examination, the articular surfaces of the femur and tibia were markedly damaged in control group with higher Mankin score and lower cartilage surface thickness. However, OA related cartilage defects were alleviated by the treatment of MSC and/or CMC. The expressions of apoptotic and inflammatory cytokines were decreased and cartilage extracellular matrix (ECM) related collagens I and II were enhanced by the treatment of MSC and/or CMC. In conclusion, this study showed that CMC and MSC treatments have a beneficial effects on OA via the protection of cartilage damage, the stimulation of ECM, and the inhibition of inflammatory and apoptotic reaction.

• Journal of Korean Society of Environmental Engineers
• /
• v.22 no.4
• /
• pp.723-731
• /
• 2000

In recent years, the amount and number of synthetic organic compounds(SOCs) discharged from various industries has been increasing. Granular activated carbon(GAC) adsorption is one of the best available technology to remove SOCs from water supplies and wastewater. In this paper competitive adsorption for binary mixture of 4-nitrophenol and phenol on reverse stratified tapered adsorber(RSTA) using GAC was studied. Two isotherm experiments were conducted, one for phenol and the other for 4-nitrophenol. The phenol data of binary mixture isotherm were not fitted to Freundlich isotherm. The competitive adsorption increased significantly with decreasing carbon dose and increasing adsorbate concentration. The RSTA was found to provide an increase in breakthrough time when decreasing flow rate, increasing angle and injection layers. The performance enhancement provided by RSTA can be exploited in separation and in the purification of fluids.

• Journal of Hydrogen and New Energy
• /
• v.21 no.3
• /
• pp.227-240
• /
• 2010

Coal gasification is heading for a great future as one of the cleanest energy sources, which can produce not only electricity and heat, but also gaseous and liquid fuels from the synthesis. The work focuses on 300MW shell type one-stage entrained flow coal gasifier which is used in the Integrated coal Gasification Combined Cycle(IGCC) plant as a reactor. As constructing an IGCC plant is considerably complicated and expensive compared with a pulverized-coal power plant, it is important to determine optimum design factors and operating conditions using a computational fluid dynamics (CFD) model. In this study, the results of numerical calculations show that $O_2$/Coal ratio, 0.83, Steam/Coal ratio, 0.05, coal particle diameter, $100{\mu}m$, injection angle, $4^{\circ}$ (clockwise) are the most optimum in this research.