• Asian-Australasian Journal of Animal Sciences
• /
• 제21권2호
• /
• pp.262-269
• /
• 2008

The aim of this study was to determine the effects of breeder age and stocking density on performance, carcass characteristics and some stress parameters (H-L ratio, serum glucose, cholesterol and triglyceride levels, tonic immobility test (TI), antibody production, relative asymmetry (RA) and external appearances). This experiment was carried out with 705 one-day old male broiler chicks (Ross 308) obtained from three different ages of broiler breeder (32, 48 and 61 wks). Each age group was randomly divided into two stocking density groups (11.9 and 17.5 broilers per $m^2$) with 5 replications per group. The experimental period was 6 weeks. Broilers from 32 wk-old breeders had lower initial weight (p<0.001), body weight gain of the first 3 week of rearing (p<0.01), the percentage of abdominal fat (p<0.001) and serum cholesterol level (p<0.01); higher percentage of gizzard (p<0.01) and longer TI duration (p<0.001) than those from 48 and 61 wk-old breeders. Broilers reared at 17.5 b/m2 had lower final BW, body weight gain, feed consumption, feather condition and foot health (p<0.001), higher percentage of heart, H-L ratio, serum glucose and cholesterol levels (p<0.001), and longer TI durations (p<0.001). There were no significant interactions in examined parameters except for feed to gain ratio between breeder age and stocking density.

• 한국지반공학회지:지반
• /
• 제13권4호
• /
• pp.177-198
• /
• 1997

화강토는 일반 퇴적토와는 달리 풍화도, 입자파쇄성등 시료의 초기상태에 따라 전단거동을 달리하는 특성을 가지므로 각 경우에 대한 응력-변형률 관계를 밝히고 전단강도의 변화특성을 조사할 필요가 있다. 이와같은 관점에서 본 연구에서는 모암조성성분 및 풍화도를 달리하는 4개지역의 화강토를 채취하여 불교란 및 교란(정적다짐)상태에서 직접전단시험과 삼축압축시험(CU, CD)을 수행하였다. 이 결과 불교란화강토의 응력-변형률거동은 구속압이 작을때는 과압밀점토의 응력경로거동처럼 경화에서 연화거동을, 교란화강토는 풍화도에 관계없이 퇴적점토와 같은 경화-일정거동을 나타내었다. 또한, 통상적인 직접전단시험에서 얻는 점착력은 특히, 불교란화강 토에서 과대평가 되는 경향이 있으며 삼축압축시험에서의 응력비(q/p')와 체적변형률증뚠비 (dv/de)의 관계는 함수비, 풍화도, 구속압력, 교란에 관계없이 하나의 식($dv/d\varepsilon,=\alpha(M-\eta))$으로 근사화시킬 수 있었다.

• 터널과지하공간
• /
• 제15권2호
• /
• pp.157-167
• /
• 2005

암반 내 작용하는 초기응력은 굴착되는 공동의 안정성이나 파괴 거동을 평가하는데 요구되는 주요 매개변수들 중의 하나이며 그 중요성은 암반 구조물의 시공 심도가 깊어지고 단면 규모가 커질수록 증가하게 된다. 이 논문에서는 경기육괴의 동북부에 위치한 춘천-양구 산악지역의 초기응력 분포 특성을 파악하기 위한 연구를 수행하였다. 현장 초기응력 측정은 연구지역내 9개 개별 시추공을 대상으로 심도 220m\~290m 구간의 49개소에서 시행되었다. 모든 수압파쇄 균열 조사는 초음파 주사검층을 이용하여 수행하였다. 연구 결과 조사지역 내에서 분포 암종의 차이에 따라 서로 상이한 분포 특성을 나타내는 초기응력장이 관찰되었고 특히 심도 200 m 이상의 관입 화강암체내에는 3.0에 가까운 측압계수를 가지는 높은 수준의 과잉 수평응력장이 형성되어 있는 것으로 분석되었다. 그리고 조사지역내에서 초기응력 조건에 의한 취성파괴 가능성을 평가한 결과 화강암 분포 지역내 심도 100 m이상인 영역에서는 굴착된 암반 구조물 주변에서 취성파괴의 가능성이 있는 것으로 분석되었다.

• 한국추진공학회지
• /
• 제16권3호
• /
• pp.90-96
• /
• 2012

복합재 연소관의 접합 체결부 최적의 설계 길이를 결정하기 위해 접합부 길이변화에 따른 구조해석을 수행하였다. 이때, 접착 체결부의 길이는 50 mm에서 300 mm의 범위를 갖는다. 무응력 상태의 초기 접합부 길이대비 응력구배가 발생하는 않는 구간의 길이를 "응력구배 길이 비"로 정의하고 이를 접착 체결부 길이선정을 위한 평가기준으로 정의하였다. 구조해석 결과 접착 체결부의 길이가 200 mm 이상으로 증가할 경우 응력구배 길이 비의 증가가 서서히 나타남을 확인하였다. 이는, 접착 체결부에 적용되는 2,500 psi 내압에서 구조적 안전성을 확보하는 최적화된 접착 체결부의 길이가 200 mm임을 의미한다.

• 한국농공학회지
• /
• 제34권3호
• /
• pp.33-42
• /
• 1992

The shear strength of cohesionless Soils results from particle-to-particle friction and structural resistance by interlocking. And, the shear strength of soils is subjected to vary depending on the internal states and external condtions. If the volume change occurring in the soils and stress-strain relationships under the internal and external changes can accrurately he described, it is possible to predict the behaviors of soils. To accomplish these objectives a series of drained triaxial compression tests and isotropic compression test was performed on the Banwol sand at different relative densities ranging from 20% to 80% and different confining pressures ranging from 0.4kgf/cm$^2$ to l2kgf/cm$^2$. The results and main conclusions of the study are summarized as follows; 1.When the relative density or the confining pressure is increased, the maximum deviator stress is increased. The ratio of the maximum deviator stress and the confining pressure is linearly proportional to the relative density. 2.It is observed that the dilatancy depends not only upon its relative density but also the confining stress, and that the maximum deviator stress is obtained after the diatancy occurs. 3.The volume of sands undergoes initial contraction prior to the dilatancy occurred by strain softening. The dilatancy rate eventually approaches the critical state or a constant volume. 4.At lower strains, Poisson's ratio approaches a certain minimum value regadless of the state of materials. At larger strains, however, the ratio is increased as the relative density is increased. 5.It is observed that the modulus of elasticity is linearly proportional to the relative density and the pressure. 6.When the relative density is increased, the friction angle of sands is linearly increased. 7.When the relative density is increased, the expansion index and the compression index are linearly decreased, and the ratio of the two is about 1/3.

• 한국기계가공학회지
• /
• 제9권1호
• /
• pp.25-34
• /
• 2010

Fretting damage reduces fatigue life of the material due to low amplitude cyclic sliding and changes in the contact surfaces of strongly connected machine and structures such as bolt, key, fixed rivet and connected shaft, which have relative slip of repeatedly very low frequency amplitude. In this study, the fretting fatigue behavior of 7050-T7451 aluminum alloys used mainly in aircraft and automobile industry were evaluated. The plain fatigue test and fretting fatigue test under cyclic bending load carried out commercial bending fatigue tester and specially devised equipments to cause fretting damage. From these experimental work, the following results obtained: (1) The plain fatigue limit for stress ratio R=-l was about 151MPa. (2) In case of fretting fatigue, fatigue limit for stress ratio R=-l about 72MPa, the fatigue limit for R=0 about 81MPa, and the fatigue limit for R=0.3 about 93MPa. (3) The fatigue limit reduction rates by the fretting damage were about 52%(R=-1), 46%(R=0) and 38%(R=0.3) respectively. (4) The fatigue limit reduction rate decreased with stress ratio increase. In fretting bending test, as stress ratio increased, occurrence of initial oblique crack by fretting decreased or phased out, so that fracture surfaces were formed by plain fatigue crack occurrence, and such tendency was notable as stress amplitude increased. (5) Tire tracks and rubbed scars were observed in the fracture surface and contacted surface.

• 한국지반공학회논문집
• /
• 제30권4호
• /
• pp.101-106
• /
• 2014

관입시험은 한정된 범위에서 1차원적 정보를 얻을 수 있으나, N치는 다양한 지반설계정수와 실험적으로 연관되어 있다. 탄성파를 이용한 비파괴 검사는 역산 과정을 통해 비용 및 시간에 효율적으로 2차원 및 3차원 물성에 대한 지도를 얻을 수 있으며, N치와 탄성파 속도는 간극비, 포화도, 유효응력 등에 의해 좌우된다. 따라서 N치와 탄성파 속도간의 경험적 관계들이 제안되어 왔다. 본 연구는 다양한 간극비와 포화도를 갖는 주문진사에 대해 정지토압조건에서 탄성파를 실험적으로 측정하였다. 그 결과 하중 조건이 간극비 및 포화도에 비하여 가장 영향을 주는 요소로 나타났으며, 간극비와 포화도는 응력-속도 관계의 경향에 영향을 주었다. 각 영향인자간의 관계를 다중회귀분석을 통해 상관식으로 나타내었다.

• Journal of Welding and Joining
• /
• 제14권2호
• /
• pp.90-95
• /
• 1996

In order to investigate characteristics of surface fatigue crack propagation from a pit shaped surface defect which frequently exists around welded joints, SS400 steel with thickness of 12mm, which has been generally used for structure members, was welded with submerged-arc butt type and machined for both surface. An initial surface defect of pit shape with the aspect ratio of 2 was made on the specimen. The initial defect was located at 5 different zones over the weldment : weld metal zone, boundary between weld metal and HAZ, HAZ, boundary between HAZ and base metal. Characteristics of surface fatigue crack propagation from the defect on each region under the same loading condition were investigated and compared.

• 한국마린엔지니어링학회:학술대회논문집
• /
• 한국마린엔지니어링학회 2006년도 전기학술대회논문집
• /
• pp.267-268
• /
• 2006

The cylinder cover stud of low-speed marine diesel engine is more than just a stud. It is a large structural element occasionally weighing over 200 kg used for assembling the combustion chamber components. Therefore, to understand the structural behavior of the stud and design it safely is quite important considering a catastrophic failure which can be arisen from an inadequate use of it. In this paper, the analysis results of the structural behavior of the stud is introduced. Strain measurement results compared with FE analysis results are summarized. The results showed that 1) the stud stress increased with engine operating load, 2) the maximum stress amplitude was about 10 MPa which is far smaller than the stud's fatigue strength of 61 MPa, 3) the stress ratio is higher than 0.9 and the stud's load factor is about 20 %, and 4) about 7 % of initial pressure tightening load was reduced while changing to a nut tightened condition.

• Corrosion Science and Technology
• /
• 제7권5호
• /
• pp.243-251
• /
• 2008

Magnesium alloys become popular research topic in last decade due to its light weight and relatively high strength-to-weight ratio in the energy aspiration age. Almost all structure materials are supposed to suspend stress. Magnesium is quite sensitive to corrosive environment, and also sensitive to environmental assisted cracking. However, so far we have the limited knowledge about the environmental sensitive cracking of magnesium alloys. The corrosion fatigue (CF) test was conducted. Many factors' effects, like grain size, texture, heat treatment, loading frequency, stress ratio, strain rate, chemical composition of environment, pH value, relative humidity were investigated. The results showed that all these factors had obvious influence on the crack initiation and propagation. Especially the dependence of CF life on pH value and frequency is quite different to the other traditional structural metallic materials. In order to interpret the results, the electrochemistry tests by polarization dynamic curve and electrochemical impedance spectroscopy were conducted with and without stress. The corrosion of magnesium alloys was also studied by in-situ observation in environmental scanning electron microscopy (ESEM). The corrosion rate changed with the wetting time during the initial corrosion process. The pre-charging of hydrogen caused crack initiated at $\beta$ phase, and with the increase of wetting time the crack propagated, implying that hydrogen produced by corrosion reaction participated in the process.