• 한국세라믹학회지
• /
• 제46권1호
• /
• pp.86-93
• /
• 2009

The crack formation and the resistance of ITO film on PET substrate with a thickness of 20 nm were investigated as a function of strain. The onset strain for the increase of resistance increased with increasing strain rate, suggesting the crack initiation is dependent on the strain rate. Electrical resistance increased at the strain of 1.6% at the strain rates below $10^{-4}/sec$ while it increased at ${\sim}2%$ at the strain rates above $10^{-3}/sec$. The critical strain at which the cracks were formed is close to the proportional limit. Upon loading, the initial cracks perpendicular to the tensile axis were observed and propagated the whole sample width with increasing strain. The spacing between horizontal cracks is thought to be determined by the fracture strength and the interfacial strength between ITO and PET. The crack density increased with increasing strain. However, the effect of the strain rate on the crack density was less pronounced in ITO/PET with 20 nm ITO thickness than ITO/PET with 125 nm ITO thickness, the strength of ITO film is thought to increase as the thickness on ITO film decreases. The absence of cracks on ITO film at a strain as close as 1.5% can be attributed to the compressive residual stress of ITO film which was developed during cooling after the coating process. The higher critical strain for the onset of the resistance increase and the crack initiation of ITO/PET with a thinner ITO film (20 nm) can be linked with the higher strength of the thinner ITO film.

• Journal of Advanced Marine Engineering and Technology
• /
• 제29권8호
• /
• pp.891-898
• /
• 2005

Inertia welding is a solid-state welding process in which butt welds in materials are made in bar and in ring form at the joint race, and energy required lot welding is obtained from a rotating flywheel. The stored energy is converted to frictional heat at the interface under axial load. The quality of the welded joint depends on many parameters, including axial force, initial revolution speed and energy amount of upset. working time, and residual stresses in the joint. Inertia welding was conducted to make the large exhaust valve spindle for low speed marine diesel engine. superalloy Nimonic 80A for valve head of 540mm and high alloy SNCrW for valve stem of 115mm. Due to different material characteristics such as, thermal conductivity and flow stress. on the two sides of the weld interface, modeling is crucial in determining the optimal weld geometry and Parameters. FE simulation was performed by the commercial code DEFORM-2D. A good agreement between the Predicted and actual welded shape is observed. It is expected that modeling will significantly reduce the number of experimental trials needed to determine the weld parameters. especially for welds for which are very expensive materials or large shaft. Many kinds of tests, including macro and microstructure observation, chemical composition tensile , hardness and fatigue test , are conducted to evaluate the qualify of welded joints. Based on the results of the tests it can be concluded that the inertia welding joints of the superalloy exhaust valve spindle are better properties than the material specification of SNCrW.

• 한국지반공학회논문집
• /
• 제29권12호
• /
• pp.95-104
• /
• 2013

최근 시멘트혼합토(CSG)가 많은 설계 시공에 적용되어지고 있다. CSG재료는 경화 초기엔 흙과 같은 역학적 특성을 보이지만 시간이 경과함에 따라 점차 콘크리트 재료적 특성을 발현하게 된다. 경화된 시멘트혼합토는 작은 변형률에서 최대강도가 발현되고 이 후 급격한 취성파괴에 도달하는 탄성적인 성질을 띠게 된다. 본 연구에서는 이러한 CSG재료의 취성거동특성을 완화하고 상대적으로 취약한 인장성능을 개선하고자 PVA 섬유보강재를 적용하였다. 섬유보강 CSG재료는 재하시 하상시료와 섬유사이의 결합력으로 섬유에 인장력이 발생하여 혼합시료의 인장강도 증가와 급작스런 취성파괴발생을 방지할 수 있다. 실험결과 섬유보강만으로도 CSG재료의 응력-변형특성을 취성파괴에서 연성파괴로 유도할 수 있으며, 섬유보강에 의한 잔류강도 증가효과를 확인 할 수 있었다.

• Steel and Composite Structures
• /
• 제47권2호
• /
• pp.269-287
• /
• 2023

The WGJ420 fire-resistant weathering (FRW) steel is developed and manufactured with standard yield strength of 420 MPa at room temperature, which is expected to significantly enhance the performance of steel structures with excellent fire and corrosion resistances, strong seismic capacity, high strength and ductility, good resilience and robustness. In this paper, the mechanical properties of FRW steel plates and buckling behavior of columns are investigated through tests at elevated temperatures. The stress-strain curves, mechanical properties of FRW steel such as modulus of elasticity, proof strength, tensile strength, as well as corresponding reduction factors are obtained and discussed. The recommended constitutive model based on the Ramberg-Osgood relationship, as well as the relevant formulas for mechanical properties are proposed, which provide fundamental mechanical parameters and references. A total of 12 FRW steel welded I-section columns with different slenderness ratios and buckling load ratios are tested under standard fire to understand the global buckling behavior in-depth. The influences of boundary conditions on the buckling failure modes as well as the critical temperatures are also investigated. In addition, the temperature distributions at different sections/locations of the columns are obtained. It is found that the buckling deformation curve can be divided into four stages: initial expansion stage, stable stage, compression stage and failure stage. The fire test results concluded that the residual buckling capacities of FRW steel columns are substantially higher than the conventional steel columns at elevated temperatures. Furthermore, the numerical results show good agreement with the fire test results in terms of the critical temperature and maximum axial elongation. Finally, the critical temperatures between the numerical results and various code/standard curves (GB 51249, Eurocode 3, AS 4100, BS 5950 and AISC) are compared and verified both in the buckling resistance domain and in the temperature domain. It is demonstrated that the FRW steel columns have sufficient safety redundancy for fire resistance when they are designed according to current codes or standards.

• 한국강구조학회 논문집
• /
• 제26권2호
• /
• pp.91-103
• /
• 2014

최근에 인장강도 800MPa급 고성능 강재가 개발되었지만 플랜지와 복부판의 상호작용을 고려한 플레이트 거더의 국부좌굴에 대한 연구는 아직까지 미흡한 실정이다. 본 연구는 HSB 800을 적용한 플레이트 거더의 플랜지 국부좌굴에 대한 강도를 비선형 유한요소해석으로 평가하였다. 비선형 해석 시 I-단면을 갖는 플레이트 거더의 플랜지와 복부판은 3차원 쉘요소로써 초기결함 및 잔류응력을 고려하였으며, 고성능 강재의 재료모델은 다중선형 재료로 모형화하였다. 이를 적용하여 복부판이 조밀, 비조밀 그리고 세장 단면을 갖는 압축 플랜지에 대해 매개변수 해석을 수행하였다. 플레이트 거더의 플랜지 국부좌굴에 대한 거동을 분석하였고, 본 연구의 비선형 해석 결과를 AASHTO LRFD(2012)와 도로교설계기준(한계상태설계법, 2012)의 압축플랜지 공칭휨강도와 비교하여 평가하였다.