• Tribology and Lubricants
• /
• v.16 no.6
• /
• pp.477-483
• /
• 2000

Rolling contact fatigue (RCF) tests were performed for two kinds of commercial silicon nitride balls using 4-Ball rolling contact fatigue life tester under EHL condition (Λ=8.9) and boundary lubrication condition (Λ=0.2). All the test balls were finished up to the dimensional accuracy of Grade 5 defined in KS B 2001 (Steel Balls for Ball Bearings) with a size of 8.731 mm. RCF tests were then conducted under the initial theoretical maximum contact stress 6.63 GPa and the spindle speed 10,000 rpm. All the test balls were not failed until 3.75 $\times$ 107 contact cycles and wear tracks of test balls were not conspicuous under EHL condition (Λ= 8.9). In the operations of low lambda regime (Λ= 0.2), all the test balls were surface damaged and high rolling wear resistance was achievable in fully densified using MgO 1 wt% and HIPed balls. Rolling wear of silicon nitride balls under boundary lubrication condition depend mainly on grain size and intergranular phase content of silicon nitride balls.

• Proceedings of the Korea Water Resources Association Conference
• /
• 2009.05a
• /
• pp.107-111
• /
• 2009

The parameters in the Horton's model which has well known as typical infiltration model were determined by the use of the optimization technique. It was assumed the initial infiltration capacity in this model was related to the antecedent precipitation per 10 days with linear combination. And both the parameters of the ultimate infiltration capacity and the decay factor were determined uniquely on a basin. Thus the optimal model's parameters representative to a basin were obtained and the Horton's infiltration equations by rainstorm events were determined. The data of ten rainstorm events for this study were observed at the Jeonjeokbigyo station located at the Selmacheon experimental basin that was $8.5\;km^2$ wide in the Imjin river.

• Journal of IKEEE
• /
• v.15 no.2
• /
• pp.149-156
• /
• 2011

In this paper, a new discrete variable structure controller based on a new sliding surface and discrete version of the disturbance observer is suggested for the control of uncertain linear systems. The reaching phase is completely removed by introducing a new proposed sliding surface. The discrete version of the disturbance observer is derived for the effective compensation of the effect of uncertainties and disturbances. A corresponding control input with the disturbance compensation is selected to guarantee the quasi sliding mode on the predetermined sliding surface for guaranteeing the designed output in the sliding surface from any initial condition to the origin for all the parameter variations and disturbances. By using Lyapunov function, the closed loop stability and the existence condition of the quasi sliding mode is proved. Finally, an illustrative example is presented to show the effectiveness of the algorithm.

• Journal of the Korean Society for Precision Engineering
• /
• v.23 no.6 s.183
• /
• pp.180-186
• /
• 2006

To investigate the bone remodeling phenomenon around implant device, 3-D mathematical simulation model was developed. Strain energy density from the finite element method was chosen for the indicator for remodeling process. Recursive calculations continued until converged results between FEM and mathematical model. For a osteo-integration example, bone-remodeling process in a implanted tibia of beagle was adapted. Calculated results indicated that the bone densities around screw pitch were increased which indicates firm fixations between the bone and implant. Screw design parameters have an influence on initial stability of the implant rather than remodeling process.

• Journal of Advanced Research in Ocean Engineering
• /
• v.1 no.1
• /
• pp.36-43
• /
• 2015

Since the crack generation and its propagation caused by welding defects is one of the main hull damage patterns, the simulation of crack propagation process has an important significance for ship safety. Based on interface element method, a finite element model to simulate crack propagation is studied in the paper. A Lennard-Jones type potential function is employed to define potential energy of the interface element. Tensile tests of steel flat plates with initial central crack are carried out. Surface energy density and spring critical stress that are suitable for the simulation of crack propagation are determined by comparing numerical calculation and tests results. Based on a large number of simulation results, the curve of simulation correction parameter plotted against the crack length is calculated.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.3
• /
• pp.630-635
• /
• 2010

In this paper, a new discrete static output feedback variable structure controller based on a new dynamic-type sliding surface and output feedback discrete version of the disturbance observer is suggested for the control of uncertain linear systems. The reaching phase is completely removed by introducing a new proposed dynamic-type sliding surface. The output feedback discrete version of disturbance observer is derived for effective compensation of uncertainties and disturbance. A corresponding control with disturbance compensation is selected to guarantee the quasi sliding mode on the predetermined dynamic-type sliding surface for guaranteeing the designed output in the dynamic-type sliding surface from any initial condition for all the parameter variations and disturbances. Using Lyapunov function, the closed loop stability and the existence condition of the quasi sliding mode is proved. Finally, an illustrative example is presented to show the effectiveness of the algorithm.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.58 no.4
• /
• pp.735-741
• /
• 2009

This paper presents an algorithm for the permanent magnet shape optimization of a large scale BLDC(Brushless DC) motor to minimize the cogging torque. A response surface method (RSM) using multiquadric radial basis function is employed to interpolate the objective function in design parameter space. In order to get a reasonable response surface with relatively small number of sampling data points, additional sampling points are added on the basis of design sensitivity analysis computed by using FEM. The algorithm has 2 stages: the first stage is to determine the PM arc angle, and the 2nd stage is to optimize the magnet pole shape. The developed algorithm is applied to a 5MW BLDC motor to get a minimum cogging torque. After 3 iterations with 4 design parameters, the cogging torque is reduced to 13.2% of the initial one.

• Proceedings of the KIPE Conference
• /
• 2009.11a
• /
• pp.96-98
• /
• 2009

This paper propose a method to detect the rotor position of IPMSM(Interior permanent magnet synchronous motor) at standstill without a position sensor. The proposed method is based on current variation caused by the magnetic saturation of stator core as rotor position. By choosing an appropriate voltage vector and applying it to phase winding, it enables the algorithm to discern between a north pole and south pole, and subsequently estimates an absolute position. This method dose not depend on the model of the motor and the motor parameter.

• Proceedings of the KIEE Conference
• /
• 1997.07a
• /
• pp.195-197
• /
• 1997

In this paper, the optimal design of interior permanent magnet synchronous motors for electric vehicle driver system is achieved to maximize the torque in constant torque region. Initial design is peformed taking into account load characteristics of electric vehicle and we use sequential uncostrained minimization techniques. In the results, the torque in constant torque region is improved about 13.5%.

• The Transactions of The Korean Institute of Electrical Engineers
• /
• v.59 no.6
• /
• pp.1167-1172
• /
• 2010

In this paper, a new discrete integral variable structure controller based on the a new sliding surface and discrete version of the disturbance observer is suggested for the control of uncertain linear systems. The reaching phase is completely removed by introducing a new proposed integral sliding surface. The discrete version of disturbance observer is derived for effective compensation of uncertainties and disturbance. A corresponding control with disturbance compensation is selected to guarantee the quasi sliding mode on the predetermined integral sliding surface for guaranteeing the designed output in the integral sliding surface from any initial condition for all the parameter variations and disturbances. Using Lyapunov function, the closed loop stability and the existence condition of the quasi sliding mode is proved. Finally, an illustrative example is presented to show the effectiveness of the algorithm.