• Journal of the Institute of Electronics Engineers of Korea TC
• /
• v.46 no.2
• /
• pp.11-17
• /
• 2009

This paper presents a new adaptive relay selection scheme for a regenerative orthogonal frequency division multiplexing access(OFDMA) relay network with fairness constrains. In the Proposed scheme, we select the best M relays out of a set of K potential relays to maximize system capacity. Among these selected relays, subcarriers are reallocated to satisfy fairness constraints as well as to minimize the degradation of the system performance. Afterwards, power allocation is performed for each subcarrier based on the water-filling method to enhance the performance improvement. By using the trade-off relationship between the system capacity and the fairness, the modified version of proposed scheme is also investigated.

• IEIE Transactions on Smart Processing and Computing
• /
• v.4 no.6
• /
• pp.384-390
• /
• 2015

There are two main artifacts in reconstructed images from in-beam positron emission tomography (PET). Unlike generic PET, in-beam PET uses the annihilation photons that occur during heavy ion therapy. Therefore, the geometry of in-beam PET is not a full ring, but a partial ring that has one or two openings around the rings in order for the hadrons to arrive at the tumor without prevention of detector blocks. This causes truncation in the projection data due to an absence of detector modules in the openings. The other is a ring artifact caused by the gaps between detector modules also found in generic PET. To sum up, in-beam PET has two kinds of gap: openings for hadrons, and gaps between the modules. We acquired three types of simulation results from a PET system: full-ring, C-ring and dual head. In this study, we aim to compensate for the artifacts that come from the two types of gap. In the case of truncation, we propose a method that uses prior knowledge of the location where annihilations occur, and we applied the discrete-cosine transform (DCT) gap-filling method proposed by Tuna et al. for inter-detector gap.

• Journal of the Korean Institute of Gas
• /
• v.21 no.2
• /
• pp.58-63
• /
• 2017

Currently, the safety monitoring process in a complex plant environment is proceeded by human. Sometimes, human error that may occur in a filed causes an severe problem. This paper introduces new method of safety monitoring system using sound information and fuzzy theory that is one of intelligent theories, in order to recognize the status of plant environment. In this paper, the filling station of high pressure gas will be used as a test plant. The result system will be widely applied for more complex plant environments.

• Journal of Korean Society of Industrial and Systems Engineering
• /
• v.38 no.1
• /
• pp.44-51
• /
• 2015

When manufacturing die casting mold, generally, the casting layout design should be considered based on the relations of injection system, casting condition, gate system, and cooling system. According to the various relations of the conditions, the location of product defects was differentiated. High-qualified products can be manufactured as those defects are controlled by the proper modifications of die casting mold with keeping the same conditions. In this research, Computer Aided Engineering (CAE) simulation was performed with the several layout designs in order to optimize the casting layout design of an automotive part (Housing). In order to apply them into the production die-casting mold, the simulation results were analyzed and compared carefully. With the filling process, internal porosities caused by air entrapments were predicted and also compared with the modification of the gate system and overflow. With the solidification analysis, internal porosities occurring during the solidification process were predicted and also compared with the modified gate system. The simulation results were also applied into the production die-casting mold in order to compare the results and verify them with the real casting samples.

• ETRI Journal
• /
• v.37 no.4
• /
• pp.752-765
• /
• 2015

We propose a novel post-processing algorithm and its very-large-scale integration architecture that simultaneously uses the passive and active stereo vision information to improve the reliability of the three-dimensional disparity in a hybrid stereo vision system. The proposed architecture consists of four steps - left-right consistency checking, semi-2D hole filling, a tiny adaptive variance checking, and a 2D weighted median filter. The experimental results show that the error rate of the proposed algorithm (5.77%) is less than that of a raw disparity (10.12%) for a real-world camera image having a $1,280{\times}720$ resolution and maximum disparity of 256. Moreover, for the famous Middlebury stereo image sets, the proposed algorithm's error rate (8.30%) is also less than that of the raw disparity (13.7%). The proposed architecture is implemented on a single commercial field-programmable gate array using only 13.01% of slice resources, which achieves a rate of 60 fps for $1,280{\times}720$ stereo images with a disparity range of 256.

• Journal of Electrical Engineering and Technology
• /
• v.11 no.4
• /
• pp.1003-1011
• /
• 2016

In this paper, a new algorithm by using 3D warping technique to effectively fill holes that are produced when creating a virtual-viewpoint image is proposed. A hole is defined as the region that cannot be seen in the reference view when a virtual view is created. In the proposed algorithm, to reduce the blurring effect that occurs on the hole region filled by conventional algorithms and to enhance the texture quality of the generated virtual view, Exemplar Based In-painting algorithm is used. The boundary noise which occurs in the initial virtual view obtained by 3D warping is also removed. After 3D warping, we estimate the relative location of the background to the holes and then pixels adjacent to the background are filled in priority to get better result by not using only adjacent object's information. Also, the temporal inconsistency between frames can be reduced by expanding the search region up to the previous frame when searching for most similar patch. The superiority of the proposed algorithm compared to the existing algorithms can be shown through the experimental results.

• Korea-Australia Rheology Journal
• /
• v.12 no.1
• /
• pp.83-92
• /
• 2000

In resin transfer molding (RTM) process, preplaced fiber mat is set up in a mold and thermoset resin is injected into the mold. An important interest in RTM process is to minimize cycle time without sacrificing part quality or increasing cost. In this study, the numerical simulation and optimization process in filling stage were conducted in order to determine the optimum gate locations. Control volume finite element method (CVFEM) was used in this numerical analysis with the coordinate transformation method to analyze the complex 3-dimensional structure. Experiments were performed to monitor the flow front to validate simulation results. The results of numerical simulation predicted well the experimental results with every single, simultaneous and sequential injection procedure. We performed the optimization analysis for the sequential injection procedure to minimize fill time. The complex geometry of an automobile bumper core was chosen. Genetic algorithm was used in order to determine the optimum gate locations with regard to 3-step sequential injection case. These results could provide the information of the optimum gate locations in each injection step and could predict fill time and flow front.

• Journal of Positioning, Navigation, and Timing
• /
• v.10 no.1
• /
• pp.55-66
• /
• 2021

In this paper, we propose a signal propagation modeling technique for generating a positioning fingerprint DB based on Long Term Evolution (LTE) signals. When a DB is created based on the location-based signal information collected in an urban area, gaps in the DB due to uncollected areas occur. The spatial interpolation method for filling the gaps has limitations. In addition, the existing gap filling technique through signal propagation modeling does not reflect the signal attenuation characteristics according to directions occurring in urban areas by considering only the signal attenuation characteristics according to distance. To solve this problem, this paper proposes a Deep Neural Network (DNN)-based signal propagation functionalization technique that considers distance and direction together. To verify the performance of this technique, an experiment was conducted in Seocho-gu, Seoul. Based on the acquired signals, signal propagation characteristics were modeled for each method, and Root Mean Squared Errors (RMSE) was calculated using the verification data to perform comparative analysis. As a result, it was shown that the proposed technique is improved by about 4.284 dBm compared to the existing signal propagation model. Through this, it can be confirmed that the DNN-based signal propagation model proposed in this paper is excellent in performance, and it is expected that the positioning performance will be improved based on the fingerprint DB generated through it.

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.48 no.6
• /
• pp.48-60
• /
• 2011

Nowadays, the 3D community is actively researching on 3D imaging and free-viewpoint video (FVV). The free-viewpoint rendering in multi-view video, virtually move through the scenes in order to create different viewpoints, has become a popular topic in 3D research that can lead to various applications. However, there are restrictions of cost-effectiveness and occupying large bandwidth in video transmission. An alternative to solve this problem is to generate virtual views using a single texture image and a corresponding depth image. A critical issue on generating virtual views is that the regions occluded by the foreground (FG) objects in the original views may become visible in the synthesized views. Filling this disocclusions (holes) in a visually plausible manner determines the quality of synthesis results. In this paper, a new approach for handling disocclusions using depth based inpainting algorithm in synthesized views is presented. Patch based non-parametric texture synthesis which shows excellent performance has two critical elements: determining where to fill first and determining what patch to be copied. In this work, a noise-robust filling priority using the structure tensor of Hessian matrix is proposed. Moreover, a patch matching algorithm excluding foreground region using depth map and considering epipolar line is proposed. Superiority of the proposed method over the existing methods is proved by comparing the experimental results.

• Restorative Dentistry and Endodontics
• /
• v.27 no.1
• /
• pp.24-33
• /
• 2002

Leakage studies have been performed frequently, since a fluid-tight seal provided by various dental fill-ing materials has been considered clinically important. The leakage of the various root-end filling materials has been widely investigated mostly dye penetration method. These dye studies cannot offer any information about the quality of the seal of a test material over a long period of time The purpose of this study was to evaluate the microleakage of root end cavities in blood contamination filed amalgam, intermediate restorative material(IRM), light cured glass ionomer cement(GI) and mineral trioxide aggregate(MTA) by means of a modified fluid transport model. Fifty standard human root sections, each 5mm high and with a central pulp lumen of 3mm in diameter, were and filled with our commonly used or potential root end fill ing materials after they were contaminated with blood. At 24h. 72h, 1, 2, 4, 8, and 12 weeks after filling, leakage along these filling materials was determined under a low pressure of 10KPa(0.1atm) using a fluid transport model. The results were as follows : 1 MTA group showed a tendency of decreasing percent of gross leakage (20m1/day) in process of time, whereas the other materials showed a tendency of increasing in the process time. 2. At the all time interval, GI group leaked significantly less than amalgam group and IRM group (p＜0.05). 3. At the 4 weeks, the percentage of gross leakage in MTA group decreased to 0% thereafter, the low per-centage of gross leakage was maintained in MTA group until the end of the experiment, whereas the percentage in IRM group increased to 100% 4. At the 12 weeks, percentage of gross leakage was significantly low in MTA group(0%), comparison with GI group(40%), amalgam group(90%) and IRM group(100%), but there was no significant difference between latter two materials.