• Journal of the Institute of Electronics Engineers of Korea CI
• /
• v.46 no.4
• /
• pp.87-93
• /
• 2009

Wireless mesh networks (WMNs) are emerging technologies that provide ubiquitous environments and wireless broadband access. The aggregate capacity of WMNs can be improved by minimizing the effect of channel interference. The IEEE 802.11b/g standard which is mainly used for the network interface technology in WMNs provides 3 multiple channels. We must consider the channel scanning delay and the channel dependency problem to effectively assign channels in like these multi-channel WMNs. This paper proposes a cluster-based channel assignment (CB-CA) algorithm for multi-channel WMNs to solve such problems. The CB-CA does not perform the channel scanning and the channel switching through assigning co-channel to the inter-cluster head (CH) links. In the CB-CA, the communication between the CH and cluster member (CM) nodes uses a channel has no effect on channels being used by the inter-CH links. Therefore, the CB-CA can minimize the interference within multi-channel environments. Our simulation results show that CB-CA can improve the performance of WMNs.

• The Journal of The Korea Institute of Intelligent Transport Systems
• /
• v.2 no.1 s.2
• /
• pp.1-13
• /
• 2003

This International Standard establishes an AVI/AEI System based on radio frequency technologies. This system is intended for general application in ITS. Specially, It allows the transfer of the identification codes and further information about equipment and vehicles used in intermodal transport into such CVO and information systems related to Intermodal Transport processes. The aim of this standard is to define, describe and specify Architecture, System Parameters, Numbering/ Data structures and interface related to an AVI/AEI system to provide an enabling Standard, which, whilst allowing the system specifier to determine the performance levels and operating conditions, provides a framework for nominal interoperability. The Standard is to establish a common framework to achieve unambiguous identification in AVI/AEI applications. Thes is AVI/AEI is designed to be an 'enabling' structure to allow interoperability between different commercial systems, and not prescriptive in determining any one system. The ISO TC204 WG4 has eight active work items. A new WI on ERI is progressing quickly; three WIs for the road environment and four multimodal WIs are under development. All Work Items are joint between CEN TC278 and ISO TC204 according to the Vienna Agreement, with CEN in the lead. The work is progressing with some delay. For all the work items, the countries who have appointed experts we: Australia, Austria, Belgium, Canada, Czech, Denmark France, Germany, Japan, Korea, the Netherlands, Norway, Spain, Sweden, UK and USA. There are 30 registered experts. The study focus on the AVI/AEcl standardization and developing of the Korea standard

• Journal of the Institute of Electronics Engineers of Korea SP
• /
• v.43 no.1 s.307
• /
• pp.27-38
• /
• 2006

The main purpose of rate control is to achieve the highest video quality when bandwidth or storage capacity is limited. For this purpose, we need a rate control algorithm which is adaptively controlled by the motion information of sequences, scene change, buffer capacity and time-varing bandwitdh channels. A rate-control method in the encoder requires the accurate estimation of target bit for each frame and the low end-to-end delay for transmitting video data by intelligent selection of encoding parameters. In this paper, we suggest three kinds of linear relation in the encoder to satisfy the characteristics of rate control. The first relation is that between the percentage of zero quantized transformed coefficients(p) and coded bits. Second relation is that between the PSNR of encoded frame and its Quantization parameter(QP). Finally, we can find out a linear approximation between QP and p. According to the experimental analysis, the proposed method results in an efficient rate control in terms of the bit estimation, the buffer capacity, and PSNR compared with the existing rate control in the H.264 JM 9.3.

• Journal of the Korean Institute of Telematics and Electronics T
• /
• v.36T no.4
• /
• pp.71-81
• /
• 1999

We propose a new CPLD(Complexity Programmable Logic Device) technology mapping algorithm improving run-time under time constraint. In our technology mapping algorithm, a given logic equation is constructed as the DAG(Directed Acyclic Graph) type, then the DAG is reconstructed by replicating the node that outdegree is more than or equal to 2. As a result, it makes delay time and the number of CLBs, run-time to be minimized. Also, after the number of multi-level is defined and cost of each nodes is calculated, the graph is partitioned in order to fit to k that is the number of OR term within CLB. The partitioned nodes are merged through collapsing and bin packing is performed in order to fit to the number of OR term within CLB(Configurable Logic Block). In the results of experiments to MCNC circuits for logic synthesis benchmark, we can shows that proposed technology mapping algorithm reduces run-time and the number of CLBs much more than the TEMPLA.

• Journal of Broadcast Engineering
• /
• v.14 no.6
• /
• pp.661-675
• /
• 2009

The carelessly and illegally copied contents are raising serious social problem as internet and multimedia technologies are advancing. Therefore, development of video copy detection system must be settled without delay. In this paper, we propose the hierarchical video copy detection method that estimates similarity using statistical characteristics between original video and manipulated(transformed) copy video. We rank according to luminance value of video to be robust to spacial transformation, and choose similar videos categorized as candidate segments in huge amount of database to reduce processing time and complexity. The copy videos generally insert black area in the edge of the image, so we remove rig black area and decide copy or not by using statistical characteristics of original video and copied video with center part of frame that contains important information of video. Experiment results show that the proposed method has similar keyframe accuracy to reference method, but we use less memory to save feature information than reference's, because the number of keyframes is less 61% than that of reference's. Also, the proposed method detects if the video is copied or not efficiently despite expansive spatial transformations such as blurring, contrast change, zoom in, zoom out, aspect ratio change, and caption insertion.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.50 no.6
• /
• pp.188-198
• /
• 2013

In order to increase its performance, NAND flash memory-based storage is composed of data buses that are shared by a number of flash memories and uses a parallel technique that can carry out multiple flash memory operations simultaneously. Since the storage performance is strongly influenced by the performance of each data bus, it is important to improve the utilization of the bus by ensuring effective scheduling of operations by the storage controller. However, this is difficult because of dynamic changes in buses due to the unique characteristics of each operation with different timing, cost, and usage by each bus. Furthermore, the scheduling technique for increasing bus utilization may cause unanticipated operation delay and wastage of storage resource. In this study, we suggest various dynamic operation scheduling techniques that consider data bus performance and storage resource efficiency. The proposed techniques divide each operation into three different stages and schedule each stage depending on the characteristics of the operation and the dynamic status of the data bus. We applied the suggested techniques to the controller and verified them on the FPGA platform, and found that program operation decreased by 1.9% in comparison to that achieved by a static scheduling technique, and bus utilization and throughput was approximately 4-7% and 4-19% higher, respectively.

• Geophysics and Geophysical Exploration
• /
• v.6 no.2
• /
• pp.57-63
• /
• 2003

For the dectection of small cavity in the hard rock, we investigated the feasibility of crosswell travel-time tomography and Kirchhoff migration technique. In travel-time tomography, first arrival anomaly caused by small cavity was investigated by numerical modeling based on the knowledge of actual field information. First arrival delay was very small (<0.125 msec) and detectable receiver offset range was limited to 4m with respect to $1\%$ normalized first arrival anomaly. As a consequence, it was turned out that carefully designed survey array with both sufficient narrow spatial spacing and temporal (<0.03125 msec) sampling were required for small cavity detection. Also, crosswell Kirchhoff migration technique was investigated with both numerical and real data. Stack section obtained by numerical data shows the good cavity image. In crosswell seismic data, various unwanted seismic events such as direct wave and various mode converted waves were alto recorded. To remove these noises und to enhance the diffraction signal, combination of median and bandpass filtering was applied and prestack and stacked migration images were created. From this, we viewed the crosswell migration technique as one of the adoptable method for small cavity detection.

• Journal of Internet Computing and Services
• /
• v.15 no.1
• /
• pp.179-191
• /
• 2014

In this paper, a frame transmission method to make IEEE 802.15.4 nodes run at a new channel and its characteristics are studied when they experience difficulties in transmission of frames due to WiFi traffic. The researches on evaluating the interference from WiFi traffic, searching for a new channel with little interference or not, and changing the operating channel are analyzed. In an wireless channel overlapped with IEEE 802.11 network, the transmission delay of IEEE 802.15.4 frames, the collision of frames in sending IEEE 802.15.4 frames without applying CSMA-CA algorithm, and the operation of IEEE 802.11 nodes are explained. A transmission method of frames including frame-formated code blocks in order to use the rest part of collided IEEE 802.15.4 frame is proposed. In the experiments of the proposed method, it is observed that frame-formated code blocks are synchronized and received by receivers in case of collision, and then the collided positions in IEEE 802.15.4 frame and the characteristics of frame reception rate are analyzed. The experimental results show that the performance of the proposed method is improved in comparison to an existing method when we measure the time taken to send a channel change command and get the response in order to avoid the interference from WiFi traffic.

• Journal of Korean Society of Transportation
• /
• v.20 no.4
• /
• pp.51-61
• /
• 2002

In this dissertation, We demonstrated the Travel Time forecasting model in the freeway of multi-section with regard of drives' attitude. Recently, the forecasted travel time that is furnished based on expected travel time data and advanced experiment isn't being able to reflect the time-lag phenomenon specially in case of long distance trip, so drivers don't believe any more forecasted travel time. And that's why the effects of ATIS(Advanced Traveler Information System) are reduced. Therefore, in this dissertation to forecast the travel time of the freeway of multi-section reflecting the time-lag phenomenon & the delay of tollgate, we used traffic volume data & TCS data that are collected by Korea Highway Cooperation. Also keep the data of mixed unusual to applicate real system. The applied model for forecasting is consisted of feed-forward structure which has three input units & two output units and the back-propagation is utilized as studying method. Furthermore, the optimal alternative was chosen through the twelve alternative ideas which is composed of the unit number of hidden-layer & repeating number which affect studying speed & forecasting capability. In order to compare the forecasting capability of developed ANN model. the algorithm which are currently used as an information source for freeway travel time. During the comparison with reference model, MSE, MARE, MAE & T-test were executed, as the result, the model which utilized the artificial neural network performed more superior forecasting capability among the comparison index. Moreover, the calculated through the particularity of data structure which was used in this experiment.

• Journal of the Institute of Electronics and Information Engineers
• /
• v.52 no.3
• /
• pp.116-126
• /
• 2015

In a distributed heterogeneous computing system, the performance of a parallel application greatly depends on its task scheduling algorithm. Therefore, in order to improve the performance, it is essential to consider some factors that can have effect on the performance of the parallel application in a given environment. One of the most important factors that affects the total execution time is a critical path. In this paper, we propose the CLTS algorithm for a task scheduling. The CLTS sets the priorities of all nodes to improve overall performance by applying leveling method to improve parallelism of task execution and by reducing the delay caused by waiting for execution of critical nodes in priority phase. After that, it conditionally uses insertion based policy or duplication based policy in processor allocation phase to reduce total schedule time. To evaluate the performance of the CLTS, we compared the CLTS with the DCPD and the HCPFD in our simulation. The results of the simulations show that the CLTS is better than the HCPFD by 7.29% and the DCPD by 8.93%. with respect to the average SLR, and also better than the HCPFD by 9.21% and the DCPD by 7.66% with respect to the average speedup.